Craftsman 316794802 Owner’s Manual

4-Cycle
BACKPACK BLOWER
Model No. 316.794802
INCREDI.PULL TM
UNBELIEVABLE S TA R TI N G E A $ E _
* SAFETY * ASSEMBLY * OPERATION * MAINTENANCE * PARTS LIST * ESPANOL, R 15
CAUTION: Before using
this product, read this
manual and follow all
safety rules and operating
instructions.
Sears Brands Management Corporation, Hoffman Estates, iL 60179 U.S.A.
Visit our website: www.craftsman.com
769-05837 P01 03/10
TABLE OF CONTENTS
Rules for Safe Operation ....................................... 2
Warranty Information .......................................... 4
Know Your Unit ............................................... 4
Assembly Instructions ......................................... 5
Oil and Fuel Information ........................................ 7
Starting/Stopping Instructions ................................... 8
Operating Instructions ......................................... 9
Maintenance and Repair Instructions ............................. 10
Cleaning and Storage ......................................... 12
Troubleshooting ............................................. 13
Specifications ............................................... 14
Parts List ................................................... 30
Service Information ................................... Back Cover
SPARK ARRESTOR NOTE NOTE: For users on U.S. Forest Land and in the states of California, Maine,
Oregon and Washington. All U.S. Forest Land and the state of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by
law that certain internal combustion engines operated on forest brush and/or grass-covered areas be equipped with a spark arrestor, maintained in effective
working order, or the engine be constructed, equipped and maintained for the prevention of fire. Check with your state or local authorities for regulations
pertaining to these requirements. Failure to follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark
arrestor. Ifit requires replacement, ask your LOCAL SERVICE DEALER to install the Accessory Part #753=05297 Spark Arrestor Kit.
CALIFORNIA PROPOSITION 65 WARNING
THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATEOF CALIFORNIA TO CAUSE CANCER, BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARM.
The purpose of safety symbols is to attract your attention to possible
dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
SYMBOL MEANING
Attention is required in order to avoid serious personal injury. May
SAFETY ALERT: Indicates danger, warning or caution.
be used in conjunction with other symbols or pictographs.
NOTE: Advises of information or instructions vital to the operation or
maintenance of the equipment.
DANGER: Failure to obey a safety warning will result in serious I
injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in injury I
to yourself and others. Always follow the safety precautions to
reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in
property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire,
electric shock and personal injury.
Read the Operator's Manual and foUow all warnings and safety instructions. Failure to do so can result in serious injury to the operator
and/or bystanders. FOR QUESTIONS, CALL 1-800-4-MY-HOME®
All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve
the right to make changes at any time without notice.
I
I
+ IMPORTANT SAFETY INSTRUCTIONS +
READ ALL INSTRUCTIONS BEFORE OPERATING
rules. Please read these instructions before operating the unit in
_ ARNING: When using the unit, you must follow the safety
+ Read the instructions carefully. Be familiar with the controls and proper
+ Read this operating instruction manual carefully. Be thoroughly familiar
+ Do not operate this unit when tired, ill, or under the influence of alcohol,
+ Never allow children to operate the equipment. Never allow adults
+ All guards and safety attachments must be installed properly before
SPECIAL SAFETY WARNINGS FOR GAS ENGINES
_ WARNING: Gasoline is highly flammable, and its vapors can
+ Store fuel only in containers specifically designed and approved for the
+ Always stop the engine and allow it to cool before filling the fuel tank.
+ Always add fuel in a clean, well-ventilated outdoor area where there are
+ Never operate the unit without the fuel cap securely in place. + Avoid creating a source of ignition for spilled fuel. Wipe up any spilled fuel
order to ensure the safety of the operator and any bystanders.
Please keep these instructions for later use.
use of the unit.
with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.
drugs, or medication.
unfamiliar with the instructions to use the unit. Never allow adults to
operate the equipment without proper instruction.
operating the unit.
explode if ignited. Take the following precautions:
storage of such materials.
Never remove the fuel tank cap or add fuel when the engine is hot. Always loosen the fuel tank cap slowly to relieve any pressure in the tank before
fueling. Do not smoke.
no sparks or flames. Do not smoke.
from the unit immediately before starting the engine. Move the unit at
least 30 feet (9.1 m) from the fueling source and site before starting the
engine. Do not smoke.
+ Never start or run the unit inside a closed room or building. Breathing exhaust
fumes can kill. Only operate this unit in a well-ventilated outdoor area.
WHILE OPERATING
+ Wear safety glasses or goggles that are marked as meeting ANSI
Z87.1-1989 standards and are marked as such. Wear ear/hearing
protection when operating this unit. + Never run the unit without the the proper equipment attached. + Toreduce the risk of hearing loss associated with sound level(s), always
wear ear/hearing protection when operating this unit. + Wear heavy long pants, boots, gloves, and a long sleeve shirt. Do not
wear loose clothing, jewelery, short pants, sandals or go barefoot. Secure
hair above shoulder level. + Toavoid static electricity shock, do not wear rubber gloves or any other
insulated gloves while operating this unit. + Use the unit only in daylight or good artificial light.
+ Keep outside surfaces free from oil and fuel. + Avoid accidental starting. Be in the starting position whenever pulling the
starter rope. The operator and unit must be in a stable position while
starting. Refer to Starting/Stopping Instructions. + Do not set unit on any surface except a clean, hard area while engine is
running. Debris such as gravel, sand, dust, grass, etc. could be picked up
by the air intake and thrown out by the discharge opening, damaging unit,
property, or causing serious injury to bystanders or operator. + Use the right tool. Only use this tool for its intended purpose.
+ Do not force unit. It will do the job better and with less likelihood of injury
at a rate for which it was designed. + Do not overreach or use from unstable surfaces such as ladders, trees,
steep slopes, rooftops, etc. Always keep proper footing and balance. + Always hold the unit with a firm grip when operating.
+ Keep hands, face, and feet away from all moving parts. Do not touch or try to
stop the impeller when it is rotating. Do not operate without guards in place. + Do not put any object into openings. Do not use with any opening blocked;
keep free of dirt, debris, and anything that may reduce the air flow. + Do not touch the engine or muffler. These parts get extremely hot from
operation, even after the unit is turned off.
Donotoperatetheenginefasterthanthespeedneededtodothejob.Do notruntheengineathighspeedwhennotinuse.
Alwaysstoptheenginewhenoperationisdelayedorwhenwalkingfrom
onelocationtoanother.
Stoptheengineformaintenance,repair,toinstallorremovetheblower
tubes.Theunitmustbestoppedandtheimpellernolongerturningto avoidcontactwiththerotatingblades.
Ifyoustrikeorcomeintocontactwithaforeignobject,stoptheengine immediatelyandcheckfordamage.Donotoperatebeforerepairing
damage.Donotoperatetheunitwithlooseordamagedparts.
Useonlyreplacementpartsoraccessoriesrecommendedforthistool
thataredistributedbySearsoraCraftsmanoutlet.Useofany
replacementpartsoraccessoriespurchasedelsewheremaybe hazardous,andwillalsovoidyourwarranty.
Neverusethisunitforspreadingchemicals,fertilizersorother
substanceswhichmaycontaintoxicmaterials. Toreducefirehazard,replacefaultymufflerandsparkarrestor.Keepthe
engineandmufflerfreefromgrass,leaves,excessivegreaseorcarbon
buildup.
Turntheengineoffanddisconnectthesparkplugformaintenanceorrepair.
Neverpointtheblowerorblowingdebrisinthedirectionofpeople,
animals,orinthedirectionofwindows.Alwaysdirecttheblowingdebris awayfrompeople,animals,andwindows.Useextracautionwhen
blowingdebrisnearsolidobjectssuchastrees,automobiles,walls,etc.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating, maintenance,' and repair information.
SYMBOL MEANING SYMBOL MEANING
OTHER SAFETY WARNINGS
Always disconnect the spark plug before performing maintenance or
accessing movable parts. See Replacing the Spark Plug.
Never store the unit, with fuel in the tank, inside a building where fumes may reach an open flame (pilot lights, etc.) or sparks (switches, electrical
motors, etc.).
Allow the engine to cool before storing or transporting. Be sure to secure
the unit while transporting.
Store the unit in a dry place, secured, or at a height to prevent unauthorized use or damage. Keep out of the reach of children.
Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean, and free from debris. Clean after each use, see
Cleaning and Storage instructions.
Keep these instructions. Refer to them often and use them to instruct other users. If you loan this unit to others, also loan these instructions to them.
SPECIAL NOTE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the
fingers, hands, and joints of people prone to circulation disorders or abnormal swelling. Prolonged use in cold weather has been linked to blood
vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of
feeling in the fingers, hands or joints, discontinue use of this tool and seek medical attention. A reduced vibration system does not guarantee avoidance
of these problems. Users who operate power tools on a regular basis must closely monitor their physical condition and the condition of this tool.
SAVE THESE INSTRUCTIONS
CRAFTSMANFULL WARRANTY
If this Craftsman product fails due to a defect in material or workmanship within two years from the date of purchase, return it to any Sears store, Parts & Repair Service Center, or other Craftsman outlet in the United States for free repair (or replacement if repair proves impossible).
This warranty applies for only 90 days from the purchase date if this product is ever used for commercial or rental purposes. This warranty covers ONLY defects in material and workmanship. Sears will NOT pay for:
Expendable items that can wear out from normal use within the warranty period, such as cutting line, filters or spark plugs.
Repairs necessary because of accident or failure to operate or maintain the product according to all supplied instructions.
Preventive maintenance, or repairs necessary due to improper fuel mixture, contaminated or stale fuel. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
On/Off Control
Cruise Control
Choke Lever
Suspension System
Shoulder Support
Shoulder Support Buckle Stand
Waist Support Clip
Throttle Grip
Air Filter Cover
Starter Rope Handle
Gas Cap
Waist Support
Trigger
Muffler
Primer Bulb
Blower Tube
Oil Fill Plug
Gas Tank
Elbow Tube
Nozzle
ASSEMBLING THE BLOWER TUBE
unit, shut the unit off before removing or installing the blower tubes.
installing the Flex Tube
1. Place a hose clamp over the end of the Flex Tube (Fig. 1A).
2. Slide the end of the Flex Tube with the clamp on it over the elbow tube (Fig. 1, B).
3. Tighten the screw on the hose clamp to secure the Flex Tube to the
elbow tube (Fig. 1, C).
B
A
Installing the Lower Blower Tubes and Nozzle
1. Align the bump slot on the end of the lower blower tube with the bump on the bottom end of the upper blower tube (Fig. 3, A).
2. Insert the bump on the upper blower tube into the bump slot on the lower blower tube (Fig. 3, A).
3. Twist the lower blower tube clockwise around the upper blower tube until the upper blower tube bump locks into place (Fig. 3, B).
B
Fig.3
Fig. I
installing the Upper Blower Tube
1. Place a hose clamp over the other end of the Flex Tube (Fig. 2, A).
2. Slide the end of the hose with the clamp on it over the top end of the upper blower tube (Fig. 2, B).
3. Tighten the screw on the hose clamp to secure the Flex Tube to the upper blower tube (Fig. 2, C).
A
B
4. Align the bump slot on the top end of the nozzle with the bump on the bottom end of the lower blower tube (Fig. 4, A).
5. Insert the bump on the lower blower tube into the bump slot on the nozzle (Fig. 4, A).
6. Twist the nozzle clockwise around the lower blower tube until the nozzle bump locks into place (Fig. 4, B).
A
Fig. 4
Fig. 2
The completed blower tube should look like Figure 5.
Throttme Cables
Upper Blower Tube
Elbow Tube
Hose Cmamp
Secure the Throttle Cables Place a zip tie around the elbow tube and the throttle cables (Fig. 6) as
shown, making sure not to crimp the cables.
Zip Tie
Zip Tie
Fig. 6
Throttme Grip
Lower Blower Tube
Nezzme
_----- Cruise Controm
Fig. 5
On/Off Switch
Adjusting the Throttle Grip
1. Move the throttle grip to a location on the upper blower tube that is comfortable for you (Fig. 7).
Throttle Grip
Upper Blower Tube
Fig. 7
2.
Using a Torx T-20 Torx screwdriver, tighten the two screws at the bottom of the throttle grip (Fig. 8).
_ ARNING: To avoid serious personal injury, make sure that the
blower tubes are locked in place or firmly installed.
Fig. 8
WARNING: OVERFILLING OIL CRANKCASE MAY CAUSE
SERIOUS PERSONAL INJURY. Check and maintain the proper oil level in the crank case; it is important and cannot be
overemphasized. Check the oil before each use while the engine is cold and change it as needed. See Changing the Oil.
RECOMMENDED OiL TYPE
Using the proper type and weight of oil in the crankcase is extremely important. Check oil before each use while the engine is cold and change the oil per the Maintenance Schedule. Failure to use the correct oil, or using
dirty oil, can cause premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American Petroleum Institute) service class SF, SG, SH.
ADDING OIL TO CRANKCASE: iNiTiAL USE NOTE: This unit is shipped without oil. In
Your unit is supplied with one 3.04 fluid oz. (90 ml.) bottle of SAE 30 SF, SG, SH oil
(Fig. 9). Funnel NOTE: Save the bottle of oil. It can be Spout
1. Unscrew the top of the bottle of oil
2.
3.
4.
NOTE:
5. Wipe up any oil that may have
Check oil before each use while the engine is cold and change the oil per the
Maintenance Schedule. Refer to
Checking the Oil Level.
CHECKING THE OIL LEVEL Check the oil only when the engine is off
and cool.
1. Place the unit on its stand on a level
2. Remove the oil fill plug from the
3. Look into the oil fill hole (Fig. 10). If
order to avoid damage to the unit, put oil in the crankcase before
you attempt to start the unit.
used to measure the correct amount during future oil changes (Fig. 9). See Changing the Oil.
and remove the paper seal O-Ring covering the opening. Replace the top. Next, cut the tip off the funnel spout (Fig. 9).
Remove the oil fill plug from the
crankcase (Fig. 10). Tilt the unit 30° to the side (Fig. 11).
Pour the entire bottle of oil into
the oil fill hole (Fig. 11).
Never add oil to the fuel or
fuel tank.
spilled and reinstall the oil fill plug.
surface.
crankcase (Fig. 10).
the oil level comes up to the first thread, then the oil is full (Fig. 12). If
it does not, fill with oil until it does.
Oil Full Line
Fig. 12
Fig.9
OilFIllPlug
Fig. 10
o
Fig. I i
RECOMMENDED FUEL TYPE Old fuel is the primary reason for improper unit performance. Be sure to use
fresh, clean, unleaded gasoline. NOTE: This is a four-cycle engine. In order to avoid damage to the unit, do
Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol,
methanol or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1% water in the fuel can make fuel and oil separate or form acids when stored.
Use fresh fuel (less than 60 days old), when using alcohol-blended fuel. Using Blended Fuels
_ WARNING: Add fuel in a clean, well ventilated outdoor area. Wipe |
_ WARNING: Gasoline is extremely flammable. Ignited vapors may
If you choose to use a blended fuel, or its use is unavoidable, follow recommended precautions:
Always use fresh unleaded gasoline
Use the fuel additive STA-BIL@ or an equivalent
Drain tank and run the engine dry before storing unit Using Fuel Additives The use of fuel additives, such as STA-BIL® Gas Stabilizer or an equivalent,
will inhibit corrosion and minimize the formation of gum deposits. Using a fuel additive can keep fuel from forming harmful deposits in the carburetor
for up to six (6) months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the instructions on the container. NEVER add fuel additives
directly to the unit's gas tank. FUELING THE UNIT
_ ARNING: Remove fuel cap slowly to avoid injury from fuel spray.
1. Remove the fuel cap.
2. Place the gas container's spout into the fill hole on the fuel tank (Fig. 13)
not mix oil with gasoline.
up any spilled fuel immediately. Avoid creating a source of ignition for
spilt fuel. Do not start the engine until fuel vapors dissipate.
explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open
flames at a distance from the area.
Never operate the unit without the fuel cap securely in place.
and fill the tank.
1
Gas Can Spout
Fuel Tank
Fig. 13
NOTE: Do not overfill the tank.
3. Wipe up any gasoline that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least 30 ft. (9.1 m) from the fueling source and site before starting the engine.
NOTE: Dispose of the old gasoline in accordance to federal, state and
local regulations.
B
1
_ ARNING: Operate this unit only in a well- ventilated outdoor area.
_ ARNING: Avoid accidental starting. Make sure you are in the
STARTING INSTRUCTIONS
1. Check the oil level in the crankcase. Refer to Checking the Oil Level.
2. Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling
3. Fully press and release the primer bulb 10 times, slowly. Some amount
4. Move the choke lever to Position 1 (Fig. 14). NOTE: The unit should be started in idle. Do not squeeze the trigger until
5. Crouch in the starting position (Fig. 16). Pull the starter rope 5 times in a
NOTE: The unit uses the Incredi-PuIF Mstarting system with MAX FiRE
6. Move the choke lever to Position 2 (Fig. 14).
7. Pull the starter rope 3-5 times in a controlled motion to start the engine.
8. Squeeze and hold the trigger, or press down the cruise control, and
9. Continue to squeeze the trigger. Move the choke lever to Position 3
iF... the engine does not start, go back to step 3. iF... the engine fails to start after a few attempts, move the choke lever to
iF WARM... If the engine is already warm, start the unit with the choker lever
Carbon monoxide exhaust fumes can be lethal ina confined area.
starting position when pulling the starter rope (Fig. 16). To avoid serious injury, the operator and unit must be in a stable position while
starting. To avoid serious personal injury, make sure that the blower tube is locked in place or firmly installed.
the Unit.
of fuel should be visible in the primer bulb (Fig. 14). If fuel cannot be seen in the bulb, press and release the bulb until fuel is visible.
step 8 (Fig. 15, A).
controlled motion.
IGNITION TM, which significantly reduces the effort required to start the engine. You must pull the starter rope out far enough to hear
the engine attempt to start. There is no need to pull the rope briskly--there is no harsh resistance when pulling. Be aware that
this starting method is vastly different from (and much easier than) what you may be used to.
allow the engine to warm up for 30 to 60 seconds.
(Fig. 14) and continue warming the engine for an additional 60 seconds.
During this time the unit may be used.
Position 3 and pull the starter rope 3-8 times in a controlled motion.
in Position 2. After the unit starts, move the choker lever to Position 3.
Cruise
Control
Trigger _
Choke Lever
Fig. 14
On/Off Switch
SLOW
B
Fig. 15
Using the Cruise Control
1. Once the engine has started and warmed up, squeeze the trigger to accelerate the unit as needed (Fig. 15, B).
2. For longer periods of operation and to eliminate possible finger fatigue, move the cruise control toward the FAST position to incrementally
increase or maintain the unit's engine speed (Fig. 15, B). When the
cruise control is pressed, the trigger will recede into the handle.
3. To decrease engine speed, move the cruise control to the SLOW position and the trigger will return to the idle position (Fig. 15, B).
STOPPING INSTRUCTIONS
1. Release your hand from the trigger. Allow the engine to cool down by idling.
2. Press and hold the On/Off switch in the OFF (O) position until the unit comes to a complete stop (Fig. 15, A).
Starter Rope
Fig. 16
ADJUSTING THE SUSPENSION SYSTEM
1. Place the unit's shoulder supports over the shoulders while the unit is behind you.
2. Close the suspension system's waist support by sliding the waist support clips together (Fig. 17, A).
A
Fig. 17
NOTE: Make sure the weight of the unit is supported on the hips by the
waist support (Fig. 18, A).
A A
B
Fig. 18
9.
If weight is not on hips, loosen the shoulder supports (Fig. 19, A) and
pull the waist support handle (Fig. 18, B) to tighten. Adjust until the unit's weight rests on the hips.
A
4. Pull the shoulder support handles to tighten the shoulder supports (Fig.
17, B).
Releasing the Suspension System
1. To loosen the shoulder supports, pull up on bottom tab of the shoulder support buckles (Fig. 19, A).
2. Squeeze the top and bottom of the waist support clips to release the waist support (Fig. 19, B).
HOLDING THE BLOWER
B A
Fig. 19
Fig. 20
OPERATING TiPS
the unit, make sure blower tubes are in place before you operate the unit.
Assure the unit is not directed at anybody or any loose debris before
starting the unit.
Verify that the unit is in good working condition. Make sure the tubes are
in place and secure.
Always hold the unit securely when operating. To reduce the risk of hearing loss associated with sound level(s), hearing
protection is required. Operate power equipment only at reasonable hours--not early in the
morning or late at night when people might be disturbed. Comply with
times listed in local ordinances. Usual recommendations are 9:00 am to
5:00 pm, Monday through Saturday.
To reduce noise levels, limit the number of pieces of equipment used at any one time.
To reduce noise levels, operate power blowers at the lowest possible speed to do the job.
Check your equipment before operation, especially the muffler, air intakes and air filters.
Use rakes and brooms to loosen debris before blowing.
In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available.
Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as screens, patios, grills, porches, and gardens.
Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away.
Use the full blower nozzle extension so the air stream can work close to
the ground.
Clean up after using blowers and other equipment. Dispose of debris appropriately.
Use the cruise control (Fig. 15) to keep the trigger depressed while operating to make continuous operation easier.
APPLICATIONS
1 Use the blower for trees, shrubs, flower beds and hard-to-clean areas.
2. Use the unit around buildings and for other normal cleaning procedures.
3. Use the blower around walls, overhangs, fences and screens.
safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations.
Before operating the unit, stand in the operating position (Fig. 20). Check
for the following:
Operator is wearing proper clothing, such as boots, safety glasses or goggles, ear/hearing protection, gloves, long pants and long sleeve shirt.
Ifthe conditions are dusty, the operator is wearing a dust mask or face mask.
The unit is in good working condition. The tubes are in place and secure.
MAINTENANCESCHEDULE
WARNING: To prevent serious injury, never perform
maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that
the unit cannot start. See Replacing the Spark Plug.
Perform these required maintenance procedures at the frequency stated in
the table. These procedures should also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require special tools or skills.
NOTE: Maintenance, replacement, or repair of the emission control
CHANGING THE OiL
Ifyou are unsure about these procedures take your unit to a Sears
or other qualified service dealer.
devices and system may be performed by a Sears or other qualified service dealer.
FREQUENCY MAINTENANCE REQUIRED SEE Every 10 hours Clean and oil air filter p 10
After 1st 10
hours p 11
Every 40 hours
Change oil Check rocker arm to valve clearance and adjust
Change oil p 10 Clean spark arrestor p 12
Check rocker arm to valve clearance and p 11 adjust
Check spark plug condition and gap p 12
pl0
| | | | | | |
| | | | | |
Fig. 22
AiR FILTER MAINTENANCE
Cleaning the Air Filter Clean and re-oil the air filter per the Maintenance Schedule. It is an
important item to maintain. Failure to maintain your air filter properly can result in poor performance or can cause permanent damage to your engine.
1. Open the air filter cover. Push the locking tab on the under side of the cover inward. Then pull the air filter cover out and up. (Fig. 23).
_ ARNING: To avoid serious personal injury, always turn the
unit off and allow it to cool before you clean or service it.
_ WARNING: Wear gloves to prevent injury when handling unit.
Change the oil per the Maintenance Schedule. Change the oil while the
engine is still warm. The oil will flow
freely and carry away more impurities.
1. Remove the oil fill plug.
2. Pour the oil out of the oil fill hole and into a container by tipping
the unit to the side (Fig. 21). Allow ample time for complete
drainage.
3. Wipe up any oil residue on the unit and clean up any oil that
may have spilled. Dispose of
the oil according to Federal, Fig. 21
State and local regulations.
4. Tilt the unit 30° to the side (Fig. 22).
5. Refill the crankcase with 3.04 fluid ounce (90 ml) of SAE 30 SF,SG, SH oil.
NOTE: Use the bottle and spout saved from initial use to measure the
6. Replace the oil fill plug.
correct amount of oil. The top of the label on the bottle measures approximately 3.04 ounces (90 ml) (Fig. 22). Check the level. See
Checking the Off Level. If the level is low, add a small amount of oil and recheck. Do not overfill (Fig. 22).
Fig. 23
2. Remove the air filter (Fig. 24).
Air Filter
Back Plate
-- Locking Tab
Fig. 24
3,
Wash the filter in detergent and water (Fig. 25). Rinse the filter
thoroughly and allow it to dry.
) .7 Tabs
Fig. 25
10
Loading...
+ 22 hidden pages