Craftsman 316292642 Owner’s Manual
* SAFETY
* ASSEMBLY
* OPERATION
* MAINTENANCE
* PARTS LIST
* ESPANOL, R 11
CAUTION: Before using this product,
read this manual and follow all safety
rules and operating instructions.
Sears Brands Management Corporation, Hoffman Estates, iL 60179 U.S.A.
Visit our website: www.craftsrnan.corn
769-06626A P00 02/11
CALiFORNiA PROPOSiTiON 65 WARNING
THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS
CHEMICALS KNOWN TO THE STATEOF CALiFORNiA TO CAUSE
CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
TABLE OF CONTENTS
Safety Rules .......................................... 2
Warranty ............................................. 4
Know Your Unit ........................................ 4
Assembly instructions ................................... 4
Oil and Fuel information ................................. 5
Starting/Stopping instructions ............................ 5
Operating instructions ................................... 6
Maintenance and Repair instructions ....................... 7
Cleaning and Storage ................................... 8
Troubleshooting Chart ................................... 9
Specifications ........................................ 10
Parts List ............................................ 26
Service Numbers .............................. Back Cover
SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the states of California,
Maine, Oregon and Washington. All U.S. Forest Land and the state of
California (Public Resources Codes 4442 and 4443), Oregon and
Washington require, by law that certain internal combustion engines
operated on forest brush and/or grass-covered areas be equipped with a
spark arrestor, maintained in effective working order, or the engine be
constructed, equipped and maintained for the prevention of fire. Check
with your state or local authorities for regulations pertaining to these
requirements. Failure to follow these requirements could subject you to
liability or a fine. This unit is factory equipped with a spark arrestor, if
it requires replacement, ask your LOCAL SERVICE DEALER to installthe
Accessory Part #753-04926 Muffler Assembly.
All information, illustrations, and specifications inthis manual are based
on the latest product information available at the time of printing. We
reserve the right to make changes at any time without notice.
The purpose of safety symbols is to attract your attention to possible
dangers. The safety symbols, and their explanations, deserve your
careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they
give are not substitutes for proper accident prevention measures.
SYMBOL MEANING
SAFETY ALERT: indicates danger, warning or caution.
Attention is required in order to avoid serious personal
injury. May be used in conjunction with other symbols or
pictographs.
NOTE: Advises you of information or instructions vital to the
operation or maintenance of the equipment.
serious injury to yourself or to others. Always follow the
_ ANGER: Failure to obey a safety warning will result in
safety precautions to reduce the risk of fire, electric shock
and personal injury.
WARNING: Failureto obey asafety warning can result ininjury to yourself and others. Always follow the safety precautions
to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result inproperty damage or personal injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire
electric shock and personal injury.
Read the Operator's Manual and follow all warnings and safety
instructions. Failure to do so can result in serious injuryto the operator
and/or bystanders.
= IMPORTANT SAFETY INSTRUCTIONS =
READ ALL INSTRUCTIONS BEFORE OPERATING
= Read the instructions carefully. Be familiar with the controls and
proper use of the unit.
• Do not operate this unit when tired, ill, or under the influence of
alcohol, drugs, or medication.
Children and teens under the age of 15 must not use the unit, except
for teens guided by an adult.
All guards and safety attachments must be installed properly before
operating the unit.
inspect the unit before use. Replace damaged parts. Check for fuel
leaks. Make sure all fasteners are in place and secure. Replace parts
that are cracked, chipped, or damaged in any way. Do not operate
the unit with loose or damaged parts.
Carefully inspect the area before starting the unit. Remove all debris
and hard or sharp objects such as glass, wire, etc.
Be aware of the risk of injury to the head, hands and feet.
Clear the area of children, bystanders, and pets. At a minimum, keep
all children, bystanders, and pets outside a 50 feet (15 m) radius;
there still may be a risk to bystanders from thrown objects.
Bystanders should be encouraged to wear eye protection, if you are
approached, stop the unit immediately.
Squeeze the throttle control and check that it returns automatically to
the idle position. Make all adjustments or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
-- i_[_ ARNING: Gasoline is highly flammable and its vaporscan explode if ignited. Take the following precautions:
Store fuel only in containers specifically designed and approved for
the storage of such materials.
Avoid creating a source of ignition for spilled fuel. Do not start the
engine until fuel vapors dissipate.
Always stop the engine and allow it to cool before filling the fuel tank.
Never remove the cap of the fuel tank, or add fuel, when the engine
is hot. Never operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure in the tank.
Add fuel in a clean, weIFventilated outdoor area where there are no
sparks or flames. Slowly remove the fuel cap only after stopping
engine. Do not smoke while fueling or mixing fuel. Wipe up any spilled
fuel from the unit immediately. Always wipe unit dry before using.
Move the unit at least 30 feet (9.1 m) from the fueling source and site
before starting the engine. Do not smoke or allow sparks and open
flames near the area while adding fuel or operating the unit.
WHILE OPERATING
= Never start or run the unit inside a closed room or building. Breathing
exhaust fumes can kill. Operate this unit only in a well ventilated
outdoor area.
Wear safety glasses or goggles that meet ANSI Z87.1 standards and
are marked as such. Wear ear/hearing protection when operating this
unit. Wear a face or dust mask if the operation is dusty.
Wear heavy, long pants, boots, gloves and a long-sleeved shirt. Do
not wear loose clothing, jewelry, short pants, sandals or go barefoot.
Secure hair above shoulder level.
This unit has a clutch. The tines remain stationary when the engine is
idling, if they do not, have the unit adjusted by a Sears or other
qualified service technician.
Be surethe tines are not in contact with anything before starting the unit.
Use the unit only in daylight or good artificial light.
• Avoidaccidentalstarting.Beinthestartingpositionwheneverpulling
thestarterrope.Theoperatorandunitmustbeinastableposition
whilestarting.SeeStarting/StoppingInstructions.
Usetherighttool.Onlyusethistoolforthepurposeintended.
Useextremecautionwhenreversingorpullingtheunittowardsyou.
Donotoverreach.Alwayskeepproperfootingandbalance.Take
extracarewhenworkingonsteepslopesorinclines.
Alwaysholdtheunitwithbothhandswhenoperating.Keepafirm
griponthegrips.
Keephands,face,andfeetatadistancefromallmovingparts.Do
nottouchortrytostopthetineswhentheyarerotating.
Donottouchtheengineormuffler.Thesepartsgetextremelyhot
fromoperation,evenaftertheunitisturnedoff.
Donotoperatetheenginefasterthanthespeedneededtocultivate.
Donotruntheengineathighspeedwhenyouarenotcultivating.
Alwaysstoptheenginewhencultivatingisdelayedorwhenwalking
fromonecultivatinglocationtoanother.
Ifyoustrikeorbecomeentangledwithaforeignobject,stoptheengine
immediatelyandcheckfordamage.Donotoperatebeforerepairing
damage.Donotoperatetheunitwithlooseordamagedparts.
Stoptheunit,switchtheenginetooff,anddisconnectthesparkplug
Keepunitcleanofvegetationandothermaterials.Theymaybecome
lodgedbetweenthetinesandguard.
Toreducefirehazard,replacefaultymufflerandsparkarrestor,keep
theengineandmufflerfreefromgrass,leaves,excessivegreaseor
carbonbuildup.
AFTER USE
= Clean tines with a household cleaner to remove any gum buildup. Oil
the tines with machine oil to prevent rust.
OTHER SAFETY WARNINGS
Never store a fueled unit inside a building where fumes may reach an
open flame or spark.
Allow the engine to cool before storing or transporting. Be sure to
secure the unit while transporting.
Store the unit in a dry area, locked up or up high to prevent
unauthorized use or damage, out of the reach of children.
Never douse or squirt the unit with water or any other liquid. Keep
handles dry, clean and free from debris. Clean after each use, see
Cleaning and Storage instructions.
• Keep these instructions. Refer to them often and use them to
instruct other users. If you loan someone this unit, also loan
them these instructions.
formaintenanceorrepair.
Useonlyoriginalequipmentmanufacturerreplacementpartsand
accessoriesforthisunit.Theseareavailablefromyourauthorizedservice
SAVE THESE INSTRUCTIONS
dealer.Useofanyunauthorizedpartsoraccessoriescouldleadto
seriousinjurytotheuser,ordamagetotheunit,andvoidyourwarranty.
" SAFETY & INTERNATIONAL SYMBOLS "
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's
manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING SYMBOL MEANING
_lll_ ' SAFETY ALERT SYMBOL
A. L
O mWARNING - READ OPERATOR'S MANUAL
Indicates danger, warning or cauti0nl Maybe Used in
conjunction with Other symbols or pictographSl
Read the operator's manual(s) and follow all warnings
and safety instructions. Failure to do so can result in
serious injury to the operator and/or bystandersl
A
=THROWN OBJECTS AND ROTATING CUTTER CAN
CAUSE SEVERE INJURY
WARNING: Small objects can be propelled at high
speed, causing injury. Keep away from the rotating rotor.
• KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders, especially children
and pets, at least 50 feet (15 m.)from the operating area.
WARNING: ThroWn0bjects and i0ud noisecan cause
severeeyeinjuryand hearing!oss.Weareye prot_tion
oWEAR EYE AND HEARING PROTECTION
meeting ANSIZ87:1_1989standards and ear protection when
operatingthisunit. Use a fullface shieldwhen needed.
AlwaYS Use Clean, fresh unleaded fuel
ON / START/RUN
ON,OFFSTOPCONTROL
,ON!OFFSTOPCONTROL
QFF0r STOP
_,HOT SURFACE WARNING
Do not touch a hot muffler or cylinder. You may get
burned. These parts get extremely hot from operation.
When turned off they remain hot for a short time.
• OIL
Refer to operator s manual for the proper type of oil.
' PRIMER BULB
Push primer bulb, fully and slowly, 10 times.
• GARDEN CULTIVATORS - ROTATING TINES CAN
CAUSE SEVERE INJURY
WARNING: Stop the engine and allow the tines to
stop before installing or removing tines, or before
cleaning or performing any maintenance. Keep hands
and feet away from rotating tines.
3
CRAFTSMAN 2 YEAR FULL WARRANTY
FOR 2 YEARS from the date of purchase, this product is warranted against any defects in material or workmanship. Defective product will receive free repair or
free replacement if repair is unavailable.
For warranty coverage details to obtain repair or replacement, visit the web site: www.craftsman.com
This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT include:
• Expendable items that can wear out from normal use within the warranty period, such as blades, tines or belts.
Product damage resulting from user attempts at product modification or repair or caused by product accessories.
Repairs necessary because of accident or failure to operate or maintain the product according to all supplied instructions.
Preventive maintenance, or repairs necessary due to improper fuel mixture, contaminated or stale fuel.
This warranty is void if this product is ever used while providing commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
APPLICATION On/Off Switch
• Cultivating sod and light to medium soil
Cultivating in garden areas, around trees, etc. Grip
irotUe C//#ontrol
Starter
Rope Grip
Transport Fuel Cap
Grip
Tine Shield Handlebar
Tines
ASSEMBLING THE UNIT
Before operating, position the unit's handlebars.
NOTE: You may also need to reposition the wheel height before
using the cultivator. Refer to the Adjusting Tine Depth section.
Begin by carefully unpacking the contents and making sure that
nothing is damaged.
Knob
Primer
Air Filter/
Muffler Cover
Wheel Bracket
Assembly
Spark Plug Muffler
POSITIONING THE HANDLEBARS
1. Loosen the two knobs on the inside of the handlebars (Fig. 1).
2. With the unit upright, swing the handlebars up into the
operating position (Fig. 9).
NOTE: Take care not to pinch the throttle cable or switch wires
when positioning the handlebar.
3. Tightentheknobsto
securethehandlebarsin ,_
place(Fig.2).
NOTE:Donotover-tighten
theknobs.
4. Readjustthethrottle
cableandswitchthe
wiressotheyaresmooth
Handlebar
Knob
andtightagainstthe
handlebarassembly.This
willhelppreventthem
Fig. 1
fromcatchingorsnagging
duringnormaloperation.
INSTALLINGTHE WHEEL
BRACKET ASSEMBLY
If the wheel bracket assembly
is not installed, or if you ever
need to remove or reinstall it,
follow the ensuing
instructions.
1. With the unit on its side, Handlebar
place the wheel bracket Fig. 2
assembly on the
underside of the tine guard (Fig. 3).
I _ I WARNING: To avoid injury from the tines, wear heavy 1
-- i
_ bracket assemb y must be installed when operating the unit.
2. Install a carriage bolt through each of the slotted holes in the
3. On the TOP side of the tine guard, install a lock washer and a
4. Make sure the square shoulder of the bolts is pushed through
NOTE: Do not over-tighten the wing nuts. Loosen the wing nuts to
ADJUSTING TINE DEPTH
Tine adjustment will vary depending on the type of soil being
cultivated and how it will be used. Generally, adjusting the tines to
break the soil 4 to 6 inches is recommended for most gardens.
Adjust the tines as follows:
1. Stop the engine and disconnect the spark plug wire.
2. Loosen (do not remove) the two wing nuts on the tine guard
3. Slide the wheel bracket
4. Once the tines are in the
5. Ifthetine depth is
6. Reconnect the spark plug
gloves and a long sleeve shirt when installing the wheel
bracket assembly.
,A I WARNING: To prevent serious personal injury, the wheel
wheel bracket and into the tine guard.
wing nut onto each of the bolts (Fig. 3).
the slotted holes in the wheel bracket. Tighten the wing nuts
(Fig. 3).
adjust wheel height.
(Fig. 4).
assembly down for
shallower penetration,
and up for deeper tine
penetration.
desired position, tighten
the wing nuts, making
sure that the carriage
bolts are seated properly
through the bracket.
incorrect, repeat steps 2
to 4.
wire and continue use.
Bolt
Tine
Guard
Wing Nut,
Lock Washer
Wheel Bracket Assembly
Washer
/ Handlebar
I_:f_ / Knob
Fig. 3
OIL AND FUEL MIXING INSTRUCTIONS
Old and/or improperly mixed fuel are the main reasons for the unit
not running properly. Be sure to use fresh, clean unleaded fuel.
Follow the instructions carefully for the proper fuel/oil mixture.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates such as
ethanol, methanol, or MTBE (ether). Alcohol-blended fuel absorbs
water. As little as 1% water in the fuel can make fuel and oil separate.
Itforms acids when stored. When using alcohol-blended fuel, use
fresh fuel (less than 60 days old).
Using Blended Fuels
Ifyou choose to use a blended fuel, or its use is unavoidable, follow
recommended precautions:
• Always use the fresh fuel mix explained in your operator's manual
Always agitate the fuel mix before fueling the unit
Drain the tank and run the engine dry before storing the unit
Using Fuel Additives
The bottle of 2-cycle oil that came with your unit contains a fuel
additive which will help inhibit corrosion and minimize the formation of
gum deposits. It is recommended that you use our 2-cycle oil with this
unit. If unavailable, use a good 2-cycle oil de-signed for air-cooled
engines along with a fuel additive, such as STA-BIL® Gas Stabilizer or
an equivalent. Add 0.8 oz. (23 ml) of fuel additive per gallon of fuel
according to the instructions on the container. NEVER add fuel
additives directly to the unit's fuel tank.
reliability, pay strict attention to the oil and fuel mixing
_ AUTION: For proper engine operation and maximum
Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded
gasoline ina separate fuel can. Use a 40:1 fuel/oil ratio. Do not mix
them directly in the engine fuel tank. See the table below for specific
gas and oil mixing ratios.
NOTE: One gallon (3.8 liters)
NOTE: Dispose of the old
,_ WARNING: Remove fuel cap slowly to avoid injury from
I_ I WARNING: Add fuel in a clean, well ventilated outdoor
FILLING THE FUEL TANK
Make sure the cultivator is in
a horizontal position when
filling or adding fuel to the
tank (Fig. 5).
instructions on the 2-cycle oil container. Using improperly
mixed fuel can severely damage the engine.
of unleaded gasoline
mixed with one 3.2
oz. (95 ml) bottle of 2-
cycle oil makes a 40:1
fuel/oil ratio.
fuel/oil mix in
accordance to
Federal, State and
Local regulations.
WARNING: Gasoline is extremely flammable. Ignited vapors
may explode. Always stop the engine and allow it to cool before
filling the fuel tank. Do not smoke while filling the tank. Keep
sparks and open flames at adistance from the area.
fuel spray. Never operate the unit without the fuel cap
securely in place.
area. Wipe up any spilled fuel immediately. Avoid creating
a source of ignition for spilt fuel. Do not start the engine
until fuel vapors dissipate.
UNLEADEDGAS
1 GALLONUS
(3.8 LITERS)
1 LITER
MIXING RATIO - 40:1
2CYCLE OIL
3.2 FL. OZ.
(95 ml)
25 ml
DOWN
Fig. 4
Fig. 5
5
WARNING: Operate this unit only in a well-ventilatedoutdoor area. Carbon monoxide exhaust fumes can be
lethal in a confined area.
WARNING: Avoid accidental starting. Make sure you are
in the starting position when pulling the starter rope (Fig. 5).
To avoid serious injury, the operator and unit must be
in a stable position while starting.
STARTING iNSTRUCTiONS
1. Mix gas with oil. See Oil
and Fuel Mixing
Instructions.
2. Fill the fuel tank with the
fuel/oil mixture.
NOTE: There is no need to
3. Fullypressandreleasethe Fig. 6
4. Crouch inthe starting
5. Squeeze and hold the
NOTE: The unit uses the
IK.. The engine does not start, go back to step 3.
NOTE: If the unit is hot and fails to start within 3 pulls of the starter
STOPPING iNSTRUCTiONS
1. Release your hand from the throttle control. Allow the engine to
2. Press and hold On/Off Control in the OFF (O) position until
turn the unit on. The
On/Off Control is in
the ON ( I ) position at Start ( I )
all times (Fig. 6).
primerbulb 10times, slowly.
Someamount of fuel should Primer Bulb
be visibleinthe primer bulb
andfuel lines(Fig.7).Ifyou
can't seefuel inthe bulb,
pressandreleasethe bulb as
manytimes as it takes until
you can seefuel in it.
position (Fig.8).Do not
squeeze the throttle, pull the
starter rope with a controlled Fig. 7
motion until the unit starts. Starting
Wait and allow the unit to Position
idle for 60 seconds.
throttle control for an
additional 30 to 60 seconds
to allow the unit to warm up.
INCREDI=PULLTM
starting system, which
significantly reduces the
effort required to start Fig.8
the engine. You must pull the starter rope out far enough to hear
the engine attempt to start. There is no needto pull the rope
briskly-- there is no harsh resistance when pulling. Be aware that
this starting method is vastly different from (and much easier than)
what you may be used to.
rope, squeeze the throttle control and pull the starter rope
until the unit starts.
cool down by idling.
engine comes to a complete stop (Fig. 6).
OPERATING TiPS
when operating this unit. Do not wear loose clothing or
jewelry. Wear eye and ear/hearing protection. Wear heavy
long pants, boots and gloves. Do not wear short pants,
WARNING: Dress properly to reduce the risk of injury
sandals or operate barefoot.
1. Move the cultivator to the work area prior to starting the engine.
Transport the cultivator by pushing it on its wheels or by
carrying it by the transport grip.
WARNING: To prevent serious personal injury, neverpick-up or carry the unit while the engine is running.
2. Start the unit by following the Starting Instructions.
3. With the engine running and the
tines off the ground, depress the
throttle control to increase the
engine speed.
4. Holding both of the handlebar grips
firmly, slowly lower the cultivator _ "'
until the tines make contact with the
ground (Fig. 9).
5. As cultivating action begins, pull
back on the cultivator so that the .,.
tines can penetrate the ground, i
6. Once the ground has been broken, _ ...... ,
continue at a moderate pace until ,_ ?_ ,_.
you are familiar with the controls
and the handling of the cultivator.
7. To improve the depth of cultivation,
pull back on the unit as it moves forward to drive the tines
deeper into the ground.
8. If the tines are digging too deep or not deep enough, adjust
them according to Adjusting Tine Depth.
[' \
Fig. 9
-- i4_&l_ WARNING: To prevent serious personal injury, use extremecaution when reversing or pulling the unit towards you.
TRANSPORTING THE UNiT
I _IL I WARNING: Toprevent serious personal injury, always
1. Stop the engine.
2. Slide the wheel bracket assembly all the way down.
3. Tilt the unit back until the tines clear the ground.
4. Push or pull the unit to the next location.
5. Ifyou need to move the unit over long distances, use the
stop the engine when operation is delayed or when
transporting the unit from one location to another
transport grip.
MAINTENANCE SCHEDULE The tines are stamped "A" or "B." The tine order should be "B, A,
_1 WARNING: To prevent serious injury, never perform
I maintenance or repairs with unit running. Always service
I and repair a cool unit. Disconnect the spark plug wire to
ensure that the un t cannot start.
B, A" from left to right when facing the cultivator from the front.
6. Secure the new tines to the shaft with click pins. It may be
necessary to wash the dirt off the tines and shaft to help during
this entire process.
AIR FILTER MAINTENANCE
Perform these required maintenance procedures at the frequency
stated in the table. These procedures should also be a part of any
seasonal tune-up.
NOTE: Some maintenance procedures may require special tools or skills.
Ifyou areunsure about these procedures, take your unit to a
Sears or other qualified service dealer. Call 1=800=4=MY=HOME®
for more information.
NOTE: Maintenance, replacement, or repair of the emission
control devices and system may be performed by a Sears
or other qualified service dealer. Call 1-800-4-MY-HOME®
for more information.
In order to assure peak performance of your engine, inspection of the
engine exhaust port may be necessary after 50 hours of operation. If
you notice lost RPM, poor performance or general lack of acceleration,
this service may be required. Ifyou feel your engine is in need of this
inspection, refer service to a Sears or other qualified service dealer.
Call 1=800=4-MY-HOME® for more information. DO NOT attempt to
perform this process yourself as engine damage may result from
contaminants involved in the cleaning process for the port.
FREQUENCY MAINTENANCE REQUIRED SEE
Before starting Fill fuel tank with fresh fuel p. 5
engine
Every 10 hours Clean and re-oil air filter p. 7
Every 25 hours Check and clean spark arrestor p. 8
Check spark plug condition and gap p. 8
Every 50 hours Inspect exhaust port and spark p. 8
arrestor screen for clogging or
obstruction
_ WARNING: Toavoid serious personal injury, always turnyour unit off and allow it to cool before you clean or service it.
The condition of the airfilter is
importantto the operation of the
unit.A dirty airfilter will restrict air
flow and change the air/fuel
mixture.This isoften mistaken for Screws ,Screws
an out of adjustment carburetor.
Checkthe condition of the airfilter
beforeadjusting the idle speed
screw. Referto Air Filter
Maintenance.
Removing the Air Fig. 12
Filter/Muffler Cover
1.
Remove the four (4) screws
securing the air filter/
muffler cover (Fig. 12). Use
aflat blade or T20 Torx bit
screwdriver.
2. Pull the cover from the
engine. Do not force.
Cleaning the Air Filter inside Muffler Cover
Failure to maintain your air Fig. 13
filter properly can result in
poor performance or can
cause permanent damage to
your engine.
1. Remove air filter/muffler
cover. Refer to Removing
TINE REMOVAL AND REPLACEMENT
All 4 tines should be replaced at the same time because they will
wear evenly through normal use. Work on one side at a time.
1. Press and hold the Start (0/Stop (O) Control in the Stop (O)
position until the unit
comes to a complete stop
and disconnect the spark
plug boot from the plug.
NOTE: It may be necessary
to lay the cultivator
back in a horizontal
position on a flat level
surface with the
handles touching the
ground.
2.
Remove the click pin from Hubs on back side (not shown)
Cultivator Front Click Pin
Fig. 10
each end of the tine shaft.
Slide the tines off of the
shaft (Fig. 10).
3.
Clean and oil the shaft.
4.
When you are reinstalling
tines, lay out the tines and
compare them to those
shown in Figure 11. Note "A" Tine
specifics about each tine: Fig. 11
its hub, curvature and
lettering ("A" or "B"). This will help make sure that you are
placing the correct tines inthe correct order.
NOTE:
If you look closely, you can see a slight curvature in the tine
tips. These curves should point toward the front of the
Tine
the Air Filter/Muffler
Cover above. / J
2. Turn cover over and look
inside to locate the air filter. Fig. 14
Remove the air filter from
inside the air filter/muffler
cover (Fig. 13).
3. Wash the filter in detergent
and water (Fig. 14). Rinse
the filter thoroughly.
Squeeze out excess water.
Allow it to dry completely.
4. Apply enough clean SAE Fig. 15
30 oil to lightly coat the
filter (Fig. 15).
5. Squeeze the filter to
spread and remove
excess oil (Fig. 16).
6. Replace the air filter
inside the air filter/muffler
cover (Fig. 13).
NOTE: Operating the unit
without the air filter Fig. 16
and air filter/muffler cover assembly will VOID the warranty.
Reinstalling the Air Filter/Muffler Cover
1. Place the air filter/muffler cover over the back of the carburetor
and muffler. Align the screw holes.
2. Insert the four (4) screws into the holes in the air filter/muffler
cover (Fig. 13) and tighten. Do not over tighten.
cultivator when the tines are installed. Figure 11 shows the
curve in each tine.
5. Using Figures 10 and 11 for reference, slide on the new tines
with the hubs facing outward.
SPARK ARRESTOR MAINTENANCE
NOTE: Pay close attention when disassembling the muffler so you
can put it back together correctly. Failure to do so will
damage the unit and may cause serious personal injury.
1. Remove air filter/muffler cover. Refer to Removing the Air
Filter/Muffler Cover.
2. Locate the muffler, but do not remove it. Findthe screw on the
bottom of the muffler (Fig. 17).This screw holds the Spark Arrestor
Hood Assembly and the spark arrestor screen to the bottom of the
muffler.Remove this screw using either a Torx T20 or flat blade
screwdriver.
3. Using a small flat blade Slots
screwdriver, carefully pry
up the spark arrestor
screen from the recessed
hole, taking care to notice __
that the "raised" part of A
the spark arrestor screen _
is inside the recessed hole. Screws 7 Spark Arrestor
Remove the spark arrestor Tabs Screen Muffler
screen from the muffler. Fig. 17
4. Clean the spark arrestor screen with a wire brush. Replace it if it
is damaged, or if you are unable to clean it thoroughly.
5. Reinstall the spark arrestor screen by putting the "raised"
portion of the screen inside the recessed hole of the muffler.
Make sure that the spark arrestor screen fits flat against the
muffler.
6. Place the spark arrestor hood on top of the spark arrestor plate
with the "raised" side up and the opening facing AWAY from the
engine (Fig. 17). Verify that the exhaust will be directed AWAY 2.
from the engine.
7. Replace the screw you removed in Step 2 and tighten securely. 3.
8. Reinstall the air filter/muffler cover (Fig. 12).
j _i_ j WARNING: Ifthe spark arrest°r h°°d and spark arrestor I
CARBURETOR ADJUSTMENT
NOTE: Careless adjustments can seriously damage your unit. Contact
REPLACING THE SPARK PLUG 1.
Use a Champion RDJ7Y spark plug or equivalent. Remove the plug
after every 25 hours of operation and check its condition. 2.
1. Stop the engine and allow it to cool. Grasp the plug boot firmly
I_ WARNING: Do not sand blast, scrape or clean spark plug 1
2. Clean around the spark
3. Replace a cracked, fouled 0.025in.
4. Install a correctly-gapped spark plug in the cylinder head. Tighten by
5. Reattach the plug boot.
screen are not tightened securely, they could fall off causing
damage to the unit and possible serious personal injury.
a Sears or other qualified service dealer to make carburetor
adjustments. Call 1-800-4-MY-HOME_">for more information.
and pull it from the spark plug. 3.
electrodes. Grit in the engine could damage the cylinder. 4.
plug. Remove the spark
plug from the cylinder
head by turning a 5/8-
inch socket 5.
counterclockwise.
or dirty spark plug. Set (0.635 rnrn)
the air gap at 0.025 in.
(0.635 ram) using a feeler
gauge (Fig. 18). Fig. 18
turning the 5/8-inch socket clockwise until snug. If using a torque
wrench, torque to:
110-120 in.olb. (12.3-13.5 N,m). Do not over-tighten.
Spark Arrestor Hood Engine
TRANSPORTING
• Allow the engine to cool before transporting.
Drain fuel from unit.
Tighten fuel cap before transporting.
Secure the unit while transporting.
CLEANING
Use a small brush to clean off the outside of the unit. Do not use strong
detergents. Household cleaners that contain aromatic oils such as pine
and lemon, and solvents such as kerosene, can damage plastic housing
or handle. Wipe off any moisture with a soft cloth.
STO RAG E
Neverstore afueled unit where fumes may reach an open flame or spark.
Allow the engine to cool before storing.
Store the unit locked up to prevent unauthorized use or damage.
Store the unit in a dry, well-ventilated area.
-- 1L_ ARNING: To avoid serious personal injury,always turn yourunit off and allow it to cool before you clean or maintain it.
Store the unit out of the reach of children.
LONG TERM STORAGE
Ifyou plan on storing the unit for an extended time, use the
following storage procedure:
1. Carefully drain the fuel tank by running the unit dry or remove
fuel cap and tip the motor housing over and drain oil/gas fuel
into a container with the same 2-cycle fuel mixture. Do not use
fuel that has been stored for more than 60 days.
Start the engine and allow it to run until it stalls. This ensures
that all fuel has been drained from the carburetor.
Allow the engine to cool. Remove the spark plug and put 5
drops of any high quality motor oil or 2-cycle oil into the
cylinder. Pull the starter rope slowly to distribute the oil.
Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil from the
4. Thoroughly clean the unit and inspect it for any loose or
MOVING THE UNIT
cylinder before attempting to start the unit after storage.
damaged parts. Repair or replace damaged parts and tighten
loose screws, nuts or bolts. The unit is ready for storage.
Allow the unit to cool
before moving.
Loosen the knobs on the
handlebar.
Fold the handlebars down
as shown (Fig. 19).
Tighten the knobs.
Either carry the unit by
the shaft tube grip or
grasp the center of the
handlebar to use it as a
carrying handle (Fig. (20).
After the unit has been
moved, reposition the
handlebars and continue
operation.
Fig. 19
Fig. 20
Loading...