Craftsman 315243000 Owner’s Manual
Owner's Manual
CRRFTSMRN'I
10 in.
COMPOUND MITER SAW
Double Insulated
Model No.
315.243000
Save this manual for
future reference
CAUTION: Read and follow
all Safety Rules and Operating
Instructions before first use of
this product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
972000-710
1-00
• Safety
• Features
• Adjustments
• Operation
• Maintenance
• Parts List
NRTL/C
• Table of Contents ........................................................................................................................................... 2
• Warranty and Introduction .............................................................................................................................. 2
• Rules For Safe Operation ........................................................................................................................... 3-6
• Glossary ......................................................................................................................................................... 6
• Product Specifications and Unpacking .......................................................................................................... 7
• Labels ............................................................................................................................................................. 8
• Loose Parts and Tools Needed ...................................................................................................................... 9
• Features .................................................................................................................................................. 10-12
• Adjustments ............................................................................................................................................. 12-19
• Operation ................................................................................................................................................. 20-26
• Maintenance ............................................................................................................................................ 27-28
• Exploded View and Repair Parts List ...................................................................................................... 30-37
• Parts Ordering / Service ............................................................................................................................... 38
FULL ONE YEAR WARRANTY
If this productfails due to a defect in material or workmanshipwithin one year from the date of purchase,
Sears willrepair it free ofcharge.
Contact a Sears Service Center for repair.
If this productis used for commercial or rental purposes,this warrantyapplies only for 90 days from the date
of purchase.
This warranty gives youspecific legal rights, and you may also have other rightswhich varyfrom state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Your saw has many features for making cutting
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this saw making it easy to
maintain and operate.
_1, CAUTION: Carefully read through this entire
owner's manual before using your new saw. Pay
close attention to the Rules For Safe Operation,
and all Safety Alert Symbols including Danger,
Warning and Caution. If you use your saw
properly and only for what it is intended, you will
enjoy years of safe, reliable service.
_, Look for this symbol to point out important safety precautions. It means'attention!!!
Your safety is involved.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face shield when needed.
We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields, available at Sears Retail Stores.
The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do
not by themselves eliminate any danger, The instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning or caution. May be used in conjunction with other symbols or picto-
graphs.
A
,a,
ZL
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precauttons to reduce the risk of fire, electric shock and personal iniury
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the esk of fire, electric shock
and personal injury,
NOTE: Advises you of informatLon or instructions vital to the operation or maintenance of the equipment.
DOUBLE INSULATION
Double insulation =sa concept in safety, in electric
power tools, which eliminates the need for the usual
three-wire grounded power cord All exposed metal
parts are isolated from internal metal motor
components with protecting insulation Double
insulated tools do not need to be grounded.
,_ WARNING: Do not attempt to operate thrs tool
until you have read thoroughly and understand
completely all instructtons, safety rules, etc.
contained in this manual Failure to comply can
result in accidents involving fire. electric shock,
or serious personal injury. Save owner's manual
and review frequently for continuing safe
operation, and instructing others who may use
this tool.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the owner's
manual carefully. Learn the saw's applications
and limitations as well as the specific potential
hazards related to this tool
• GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH
GROUNDED SURFACES, For example; pipes,
radiators, ranges, refrigerator enclosures.
• KEEP GUARDS IN PLACE and in good working
order.
REMOVE ADJUSTING KEYS AND
WRENCHES. Get in the habit of checking to see
that hex keys and adjusting wrenches are
removed from tool before turning on saw
IMPORTANT
Servicing requires extreme care and knowledge of the
system and should be performed only by a qualified
service technician. For service we suggest you return
the tool to your nearest Sears store for repair. Always
use original factory replacement parts when servicing.
• KEEP THE WORK AREA CLEAN. Cluttered work
areas and work benches invite accidents. DO
NOT leave tools or pieces of wood on the saw
while it is in operation.
• DO NOT USE IN DANGEROUS ENVIRON-
MENTS, Do not use power tools near gasoline or
other flammable liquids, in damp or wet locations,
or expose them to rain Keep the work area well
lit,
KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area Do not let visitors
contact tool or extens=on cord whde operating.
MAKE WORKSHOP CHILD-PROOF w=th pad-
locks and master switches or by removrng starter
keys.
DO NOT FORCE THE TOOL. It will do the job
better and safer at the rate for which it was
designed.
USE THE RIGHT TOOL. Do not force the tool or
attachment to do a job it was not designed for.
Don't use it for a purpose not intended.
RULES FOR SAFE OPERATION (Continued)
USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
When using an extension cord, be sure to use
one heavy enough to carry the current your
product will draw. An undersized cord will cause
a drop in line voltage resulting in loss of power
and overheating. A wire gage size (A W.G ) of at
least 14 is recommended for an extension cord
25 feet or less in length. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord
INSPECT EXTENSION CORDS PERIODI-
CALLY and replace if damaged.
DRESS PROPERLY. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other
jewelry. They can get caught and draw you into
moving parts Rubber gloves and nonslip foot-
wear are recommended when working outdoors.
Also wear protective hair covering to contain long
hair
ALWAYS WEAR SAFETY GLASSES WITH
SIDE SHIELDS, Everyday eyeglasses have only
impact-resistant lenses; they are NOT safety
glasses,
PROTECT YOUR LUNGS. Wear a face or dust
mask if the cutting operation isdusty,
PROTECT YOUR HEARING. Wear hearing
protection duringextended periods of operation.
SECURE WORK. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and it frees both hands to operate tool,
DO NOT OVERREACH. Keep proper footing and
balance at all times. •
MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and
changing accessories.
DISCONNECT ALL TOOLS. When not in use,
before servicing, or when changing attachments,
blades, bits, cutters, etc., all tools should be
disconnected.
• AVOID ACCIDENTAL STARTING. Be sure
switch is off when plugging in.
• USE RECOMMENDED ACCESSORIES. The
use of improper accessories may cause risk of
injury.
• NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the blade is unin-
tentionally contacted.
• CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged must be properly repaired or replaced
by a qualified service technician at a Sears store
to avoid risk of personal injury.
NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN THE POWER OFF. Do not
leave tool until it comes to a complete stop.
FIRMLY CLAMP OR BOLT your miter saw to a
workbench or table at approximately hip height.
USE ONLY CORRECT BLADES. Do not use
blades with incorrect size holes. Never use blade
washers or blade bolts that are defective or
incorrect. The maximum blade capacity of your
saw is 10 in.
KEEP BLADES CLEAN, SHARP AND WITH
SUFFICIENT SET, Sharp blades minimize
stalling and kickback.
• DO NOT REMOVE THE SAW'S BLADE
GUARDS. Never operate the saw with any guard
or cover removed. Make sure all guards are
operating properly before each use.
• KEEP HANDS AWAY FROM CUTTING AREA.
Keep hands away from blades. Do not reach
underneath workor around or underthe blade
whileblade isrotating. Do not attempt to remove
cutmaterial when blade is moving.
WARNING: Blade coasts after turn off.
A
DO NOT ABUSE CORD. Never yank cord to
disconnect it from receptacle. Keep cord from
heat, oil, and sharp edges.
INSPECT TOOL CORDS PERIODICALLY and if
damaged, have repaired by a qualified service
technician at a Sears store. Stay constantly
aware of cord location and keep it well away
from the rotating blade.
USE OUTDOOR EXTENSION CORDS. When
tool is used outdoors, use only extension cords
with approved ground connection that are
intended for use outdoors and so marked.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by a qualified service technician at a
Sears store.
KEEP TOOL DRY, CLEAN, AND FREE FROM
OIL AND GREASE. Always use a clean cloth
when cleaning. Never use brake fluids, gasoline,
petroleum-based products, or any solvents to
clean tool.
4
RULES FOR SAFE OPERATION (Continued)
• ALWAYS SUPPORT LONG WORKPIECES to •
minimize risk of blade pinching and kickback.
Saw may slip, walk, or slide while cutting long or
heavy boards. •
• BEFORE MAKING A CUT, BE SURE ALL
ADJUSTMENTS ARE SECURE.
• GUARD AGAINST KICKBACK. Kickback occurs
when the blade stalls rapidly and workpiece is
driven back towards the operator. It can pull your
hand into the blade resulting in serious personal
injury. Stay out of blade path and turn switch off
immediately if blade binds or stalls.
• AVOID CUTTING NAILS. Inspect for and
remove all nails from lumber before cutting.
• ALWAYS USE A CLAMP to secure the work-
piece when possible.
• NEVER TOUCH BLADE or other moving parts
during use.
• NEVER START A TOOL WHEN THE BLADE IS
IN CONTACT WITH WORKPIECE. Allow motor
to come up to full speed before starting cut.
• MAKE SURE THE MITER TABLE AND SAW
ARM (BEVEL FUNCTION) ARE LOCKED IN
POSITION BEFORE OPERATING YOUR SAW.
Lock the miter table by securely tightening the
miter lock handle. Lock the saw arm (bevel
function) by securely tightening the bevel lock
knob.
• NEVER USE A LENGTH STOP ON THE FREE
SCRAP END OF A CLAMPED WORKPIECE.
NEVER hold onto or bind the free scrap end of
the workpiece in any operation. If a work clamp
and length stop are used together, they must
both be installed on the same side ol the saw
table to prevent the saw from catching the loose
end and kicking up.
• NEVER cut more than one piece at a time. DO
NOT STACK more than one workpiece on the
saw table at a time.
NEVER PERFORM ANY OPERATION "FREE-
HAND". Always place the workpiece to be cut on
the miter table and position it firmly against the
fence as a backstop. Always use the fence.
NEVER hand hold a workpiece that is too small
to be clamped. Keep hands clear of the no hands
zone
NEVER reach behind, under, or within three
inches of the blade and its cutting path with your
hands and fingers for any reason.
NEVER reach to pick up a workpiece, a piece of
scrap, or anything else that is in or near the
cutting path of the blade.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause
your hand to move into the blade. ALWAYS
make sure you have good balance. NEVER
operate your miter saw on the floor or in a
crouched position.
• NEVER stand or have any part of your body in
line with the path of the saw blade.
• ALWAYS release the power switch and allow the
saw blade to stop rotating before raising it out of
the workpiece.
• DO NOT TURN THE MOTOR SWITCH ON AND
OFF RAPIDLY. This could cause the saw blade
to loosen and could create a hazard. Should this
ever occur, stand clear and allow the saw blade
to come to a complete stop. Disconnect your saw
from the power supply and securely retighten the
blade bolt.
REPLACEMENT PARTS. All repairs, whether
electrical or mechanical, should be made by
qualified service technician at a Sears store.
WARNING: When servicing use only identical
A
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product
damage.
NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking of the motor could
ignitefumes.
NEVER leave the miter saw unattended while
connected to a power source.
POLARIZED PLUGS. To reduce the risk of
electric shock, this tool has a polarized plug (one
blade is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug
in any way.
IF ANY PART OF THIS MITER SAW IS MISS-
ING or should break, bend, or fail in any way, or
should any electrical component fail to perform
properly, shut off the power switch, remove the
miter saw plug from the power source and have
damaged, missing, or failed parts replaced
before resuming operation.
DO NOT OPERATE THIS TOOL WHILE UN-
DER THE INFLUENCE OF DRUGS, ALCOHOL,
OR ANY MEDICATION.
RULES FOR SAFE OPERATION (Continued)
• ALWAYS STAY ALERT! Do not allow familiarity •
(gained from frequent use of your saw) to cause
a careless mistake. ALWAYS REMEMBER that
a careless fraction ofa second issufficientto
inflict severe injury. •
• STAY ALERT AND EXERCISE CONTROL.
Watch what you are doing and use common
sense. Do not operate tool when you are tired. •
Do not rush.
SAVE THESE INSTRUCTIONS
Arbor
The shaft on which a blade or cutting toolis mounted.
Bevel Cut
A cutting operation made with the blade at any angle
other than 90" to the miter table,
Crosscut
A cutting or shaping operation made across the grain
of the workpiece.
Compound Miter Cut
A compound miter cut is a cut made using a miter
angle and a bevel angle at the same time.
Freehand
Performing a cut withoutusing a fence, miter gage,
fixture, work clamp, or other proper device to keep the
workpiece from twistingor moving during the cut.
Gum
A sticky, sap based residue from wood products.
Miter Cut
A cuttingoperation made withthe blade at any angle
other than 90" to the fence.
Resin
A sticky,sap base substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object
in one minute.
Saw Blade Path
The area over, under, behind, or in front of the blade.
As it applies to the workpiece, that area whichwillbe,
or has been, cut by the blade.
MAKE SURE THE WORK AREA HAS AMPLE
LIGHTING to see the work and that no obstruc-
tionswill interfere with safe operation BEFORE
performingany work usingyour saw.
ALWAYS TURN OFF SAW before disconnecting
it, to avoid accidental starting when re-connect-
ing topower supply.
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instructother users. If you
Loansomeone this tool, loan them these instroc-
tions also.
Set
The distance that the tip of the sawblada tooth isbent
(or set) outward from the face of the blade,
Throw-Back
Throwing of a workpiece in a manner similarto a
kickback.Usually associatedwith a cause other than
the kerfclosing, such as a workpiece not being
againstthe fence, being dropped into the blade, or
being placed inadvertentlyin contact withthe blade.
Through Sawing
Any cutting operation where the blade extends
completely through the thickness of the workpiece.
Workpiece
Theitem on whichthe cu_ing oper_ionis being done.
The surfaces ofa workpiece are commonlyreferredto
asfaces, ends, and edges.
Zero Clearance Throat Plate
A plasticthroat plate inserted in the miter table that
allowsfor blade clearance. When you make yourfirst
cut with your compound mitersaw, the saw blade cuts
a slotthroughthe throat plate the exact width of the
blade. This provides for a zero clearance kerrthat
minimizesworkpiece tear-out.
No Hands Zone
The area between the marked lines on the left and
rightside of the miter table base. This zone is
identifiedby no hands zone labels placed inside the
marked lines on the miter table base.
Blade Diameter i 0 in.
Blade Arbor 5/8 in.
No Load Speed 5000 RPM
Rating 120 Volts, 60 Hz-AC Only
Input 15 Amperes
Net Weight 32 Ibs.
Cutting Capacity with Miter at 0°/Bevel 0°:
5-9/16 in. wide X 2-9/32 in. thick
3-9/16 in. thick X 4 in. wide
Maximum Cutting Capacity with Miter at 45°/Bevel 0°:
3-15/16 in. wide X 2-9/32 in. thick
Maximum Cutting Capacity with Miter at 0°/Bevel 45°:
5-9/16 in. wide X 1-9/16 in. thick
Maximum Cutting Capacity with Miter at 45°/Bevel 45°:
4 in. wide X 1-9/16 in. thick
Your Compound Miter Saw has been shipped
completely assembled except for the blade, miter lock
handle, and dust guide.
WARNING: If any parts are missing, do not
operate this tool until the missing parts are
replaced. Failure to do so could result in possible
serious personal injury.
• Remove all loose parts from the carton. Separate
and check with the list of loose parts. See Figure 2.
• Remove the packing materials from around your
saw.
• Carefully lift saw from the carton and place it on a
level work surface. This saw is heavy. To avoid
back injury, get help when needed.
• Do not discard the packing materials until you
have carefully inspected the saw, identified all
loose parts, and satisfactoriry operated your new
saw.
• Your saw has been shipped with the saw arm
locked in the down position. To release saw arm,
push down on top of saw arm and pull out the lock
pin. See Figure 4.
• Lift the saw arm by the handle. Hand pressure
should remain on the saw arm to prevent sudden
rise upon release of the lock pin.
• Examine all parts to make sure no breakage or
damage has occurred during shipping.
If any parts are damaged or missing, do not attempt to
plug in the power cord and turn the switch on until the
damaged or missing parts are obtained and are
installed correctly.
7
The following labels are on the miter saw withloca-
tions indicated.
Restorelower blade guard
andsecurelytighten screw
beforeuse
e Change. See Owner's Man
DANGER: DO NOT REMOVE
ANY GUARD. USE OF SAW
WITHOUT THIS GUARD WILL
RESULT IN SERIOUS INJURY.
41WARNING/ ADVERTENCIA
• For your safety, read owners manual before operating
miter saw.
• Wear eye protection.
• Keep hands out of path of saw blade,
• Do not operate saw without guards in place,
• Do not perform any operation freehand.
• Never reach around the saw blade.
• Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
• Disconnect the saw from the power source before
changing blade or servicing,
• Do not expose to rain or usa in damp places.
• Psra su saguridad, lea el manual del usuario antes
de usar la sierra ingletadora.
10 inch Compound Miter Saw
DOUBLEINSULATED5,OOORPM120VOLTS60Hz ACONLY15A
WARNING: WHEN SERVICING, USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS,
MODEL 315,243000 SER NO _i
MADE iN TArWAN [ ] v,m_c
SEARS,ROEBUCKAND CO. rrA_ON_W¢_
• Customer Help Line 1-800-932-3188
Fig. 1
The following items are included with your Compound Miter Saw:
• Saw Blade - 10 in.
• Miter Lock Handle
• 5 mm Hex Key Wrench
• 6 mm Hex Key Wrench
• 8 mm Hex Key Wrench
: D_:tt Gui:e
• Owner's Manual
• Blade Wrench
BLADEWRENCH SAWBLADE
__HEX KEY
_KEY
MITERLOCKHANDLE
DUST BAG
_, WARNING: The use o! attachments or accessories not listed might be hazardous and could
cause serious personal injury,
The following tools (not included) are needed for checking adjustments of your saw or for installing the blade:
17mmCOMBINATIONWRENCH
10mmCOMBINATIONWRENCH
SQUARE
FRAMINGSQUARE
PHILLIPS SCREWDRIVER
Fig. 2
9
KNOW YOUR COMPOUND MITER
SAW
See Figure 3.
Before attempting to use your saw, familiarize yourself
with all operating features and safety requirements.
,_ WARNING: Do not allow familiarity with your
saw to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
ELECTRIC BRAKE
An electric brake has been provided to quickly stop
blade rotation after the switch is released.
FENCE
The fence on your compound miter saw has been
provided to hold your workpiece securely against
when making all cuts.
SELF-RETRACTING LOWER BLADE
GUARD
15 AMP MOTOR
Your saw has a powerful 15 amp motor with sufficient
power to handle tough cutting jobs. It is made with all
ball bearings, and has externally accessible brushes
for ease of servicing.
10 in. BLADE
A 10 in. saw blade is included with your compound
miter saw. Itwill cut materials up to 2-5/8 in. thick or
5-3/4 in. wide, depending upon the thickness of the
material and the setting at which the cut is being
made.
SWITCH
LOCK-OFFLEVER
DUSTBAG
UPPER
BLADEGUARD
The lower blade guard is made of shock-resistant,
see-through plastic that provides protection from each
side of the blade. It retracts over the upper blade
guard as the saw is lowered into the workpiece.
MITER LOCK HANDLE
See Figure 4.
The miter lock handle securely locks your saw at
desired miter angles.
SWITCHTRIGGER
BLADEGUARD
BEVEL
FEN
MITER
POSITIVESTOP(S)
10
MITERTABLE
ZONE LABEL
ZEROCLEARANCE
CONTROLARM
"NO HANDS ZONE"
LINE
LOCK PLATE
LOCKHANDLE
Fig. 3
CARRYING HANDLE
See Figure 4.
For convenience when carrying or transporting your
miter saw from one place to another, a carrying
handle has been provided on top of the saw arm as
shown in figure 4. To transport, turn off and unplug
your saw, then lower the saw arm and lock it in the
down position. Lock saw arm by depressing the lock
pin.
CARRYING
HANDLE
LOCK
PIN
SAW
ARM
LOCK-OFF
LEVER
SPINDLE
LOCK BUTTON
SWITCH
TRIGGER
SPINDLE LOCK BUTTON
See Figure5
A spindle lock button has been provided for locking
the spindle which stops the rotation of the blade in
your saw. Depress and hold the lock button while
installing, changing, or removing blade.
Fig. 5
MITERLOCK
HANDLE
SAW ARM
LOCKED IN DOWN POSITION
Fig. 4
POSITIVE STOPS ON MITER TABLE
Positivestops have been provided at 0°, 22-1/2° and
45°.The 22-1/2 ° and 45° positive stops have been
provided on both the left and right side of the miter
table.
BEVEL LOCK KNOB
The bevel lock knob securely locks your compound
miter saw at desired bevel angles. Positive stop
adjustment screws have been provided on each side
of the saw arm. These adjustment screws are for
making fine adjustments at 0° and 45°. See pages 18
and 19.
LOCK-OFF LEVER
See Figure 5
The switch trigger is equipped with a lock-off lever to
reduce the possibility of accidental starting. The lock-
off lever must be pressed down with the palm of your
hand to turn saw on. Once the saw is on, the lock-off
lever can be released. The spring loaded lever will
spring back into the lock-oft position when the switch
trigger is released.
SWITCH
TRIGGER
Fig. 6
TRIGGER LOCK
See Figure 6
To prevent unauthorized use of your compound miter
saw, we suggest that you disconnect it from the power
supply and lock the switch in the off position To lock
the switch, install a padlock through the hole in the
switch trigger A lock with a shackle up to 13/64 in
diameter may be used. When the lock is installed and
locked, the switch is inoperable. Store the padlock key
in another location.
11
MOUNTING HOLES
See Figure 7.
Your compound miter saw should be permanently
mounted to a firm supporting surface such as work-
bench. Four 7/16 in. bolt holes have been provided in
the saw base for this purpose. Each of the tour
mounting holes should be bolted securely using
3/8 in. machine bolts, lock washers, and hex nuts (not
included). Bolts should be of sufficient length to
accommodate the saw base, lock washers, hex nuts,
and the thickness of the workbench.
Tighten all four bolts securely.
The hole pattern for an 18 in. x 24 in. workbench is
shown in Figure 7. Carefully check the workbench
after mounting to make sure that no movement can
occur during use. If any tipping, sliding, or walking is
noted, secure the workbench to the floor before
operating.
_IL WARNING: Always make sure your compound
miter saw is securely mounted to a workbench or
an approved workstand. Failure to do so could
result in an accident resulting in possible serious
personal injury.
ELECTRICAL CONNECTION
Your saw has a precision built electric motor. It should
be connected to a power supply that is 120 volts,
60 Hz, AC only (normal household current). Do not
operate this tool on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor
will overheat. If your tool does not operate when
plugged into an outlet, double-check the power
supply.
1O_-
341/4"
-9-
I"
WARNING: The operation of any saw can
,&
result in foreign objects being thrown into your
eyes, which can result in severe eye damage.
Before starting power tool operation, always
wear safety goggles or safety glasses with side
shields and a full face shield when needed. We
recommend wide vision safety mask for use over
eyeglasses or standard safety glasses with side
shields.
WARNING: Do not attempt to modify this tool or
a,
create accessories not recommended for use
with this tool. Any such alteration or modification
is misuse and could result in a hazardous
condition leading to possible serious personal
injury.
I
Fig. 7
_ WARNING: To prevent accidental starting that
could cause possible serious personal injury,
assemble all parts to your saw before connecting
it to power supply. Saw should never be
connected to power supply when you are
assembling parts, making adjustments, installing
or removing blades, or when not in use.
As mentioned previously your saw has been factory
assembled and adjusted. The miter lock handle, dust
guide, and blade are the only parts that have to be
installed.
MITER LOCK HANDLE
See _gure 8.
To install the miter lock handle, place the threaded
stud on the end of the miter lock handle into the
threaded hole in the control arm. Turn clockwise to
tighten.
12
Loading...