Craftsman 315.235360 User Manual

Owner's Manual

CRAFTSMAN°

10 in. (254 mm)

COMPOUND MITER SAW

Double Insulated

Model No.

315.235360

Save this manual for future reference

CAUTION: Readand

.follow all Safety Rules and

Operating Instructions before first use of this product,

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

972000-473

10-97

NRTUC

• Table of Contents ........................................................................................................................................... 2

• Warranty and Introduction .............................................................................................................................. 2

• Rules For Safe Operation ........................................................................................................................... 3-6

• Glossary ......................................................................................................................................................... 6

• Product Specifications and Unpacking .......................................................................................................... 7

• Labels ............................................................................................................................................................. 8

• Loose Parts ans Tools Needed ...................................................................................................................... 9

• Features .................................................................................................................................................. 10-12

• Adjustments ............................................................................................................................................. 13-19

• Operation ................................................................................................................................................. 20-26

• Maintenance ............................................................................................................................................ 27-28

• Exploded View and Repair Parts List...................................................................................................... 30-37

• Parts Ordering / Se_,ice ....................................... :.................................................................... i"." ............. 38

FULL ONE YEAR WARRANTY ON CRAFTSMAN COMPOUND MITER SAW

If this CIIRFTSMRN Compound Miter Saw fails due to a defect in material or workmanship within one year from

the date of purchase, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY RETURNING THIS pRODUCT TO THE NEAREST SEARS STORE

IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Your saw has many features for making cutting operations more pleasant and enjoyable. Safety,

performance and dependability have been given top priority in the design of this saw making iteasy to maintain and operate.

_ CAUTION: Carefully read through this entire

owner's manual before usingyour new saw. Pay close attention to the Rules For Safe Operation,

and all Safety Alert Symbols including Danger, Warning and Caution. If you use your saw

properly and onlyfor what it is intended, you will enjoy years of safe, reliable service.

,_ Look for this symbol to point out important safety precautions. It means attention!H Your

safety is involved.

_1= WARNING:

The operation of any power tool can result inforeign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses

with side shields, available at Sears Retail Stores.

The purpose of safety symbols Is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do

not by themselves eliminate any danger. The Instructions or warnings they give are not substitutes for proper accident prevention measures.

SYMBOL

NOTE: Advises you of information or instructionsvital to the operation or maintenance of the equipment.

DOUBLE INSULATION

Double insulationis a concept in safety, in electdc

power tools,which eliminates the need for the usual three-wire grounded power cord. All exposed metal

parts are isolated from internal metal motor

components with protecting insulation.Double

insulated tools do not need to be grounded.

MEANING

SAFETY ALERT SYMBOL: Indicates danger, waming or caution. May be used in conjunction with other symbols or picto-

graphs.

DANGER: Failure to obey a safety waming will result in serious injury to yourself orto others. Always follow the safety precautionsto reduce the risk offire, electric shock and personal injury.

WARNING: Failure to obey a safety warning can result in serious injuryto yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION: Failure to obey a safety warning may resultin property damage or personal Injury to yourself orlo others. Always follow the safety precautions to reduce the risk of fire, electric shock

and personal injury.

IMPORTANT

Servicing requires extreme care and knowledge of the system and should be performed only by a qualified

service technician. For service we suggest you return the tool to your nearest Sears store for repair. Always use original factory replacement parts when servicing.

,_ WARNING: Do not attempt to operate this tool

until you have read thoroughly and understand completely all instructions, safety rules, etc. contained in this manual. Failure to comply can

result in accidents involving fire, electric shock,

or serious personal injury. Save owner's manual and review frequently for continuing safe

operation, and instructing others who may use this tool.

READ ALL INSTRUCTIONS

KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the saw's applications

and limitationsas well as the specific potential

hazards related to this tool.

• GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING:BODY CONTACT WITH GROUNDED SURFACES. For example; pipes,

radiators, ranges, refrigerator enclosures.

• KEEP GUARDS IN PLACE and in good working

order.

KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents. DO NOT leave tools or pieces of wood on the

saw while it is in operation. DO NOT USE IN DANGEROUS ENVIRON-

MENTS. Do not use power tools near gasoline or other flammable liquids, in damp or wet loca- tions, or expose them to rain. Keep the work

area well lit.

• KEEP CHILDREN AND VISITORS AWAY. All

visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors

contact tool or extension cord while operating.

• MAKE WORKSHOP CHILD-PROOF with

padlocks and master switches, or by removing starter keys.

• DO NOT FORCE THE TOOL. It will do the job

better and safer at the rate for which itwas designed.

• USE THE RIGHT TOOL Do not force the tool or

attachment to do a job it was not designed for. Don_ use it for a purpose not intended.

- : -nuI.r.o run $_ru; vru;nru4• urn1 tvvnnumuvl;_,u/

• DRESS PROPERLY. Do not wear loose clothing, •

gloves, neckties, dngs, bracelets, or other

jewelry. They can get caught and draw you into

moving parts. Rubber gloves and nonslip foot-

wear are recommended when working outdoors. Also wear protective hair covering to contain long

hair. ALWAYS WEAR SAFETY GLASSES WITH

SIDE SHIELDS. Everyday eyeglasses have only impact-rasistant lenses; they are NOT safety

glasses. PROTECT YOUR LUNGS. Wear a face or dust

mask ifthe cutting operation is dusty. PROTECT YOUR HEARING. Wear headng

protection during extended periods of operation. DO NOT ABUSE CORD. Never yank cord to •

disconnect it from receptacle. Keep cord from heat, oil, and sharp_edges.

DO NOT OVERREACH. Keep proper footing and •

balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perfor-

mance. Follow instructions for lubdcating and changing accessodes.

DISCONNECT ALL TOOLS. When not in use, before servicing, or when changing attachments,

blades, bits, cutters, etc., all tools should be disconnected.

REMOVE ADJUSTING KEYS AND WRENCHES. Get in the habit of checking to see that hex keys and adjusting wrenches are

removed from tool before turning it on.

AVOID ACCIDENTAL STARTING. Be sure switch isoff when plugging in.

USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting inloss of power and overheating. A wire gage size (A.W.G.) of at

least 14 is recommended for an extension cord 25 feet or less inlength. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier the cord.

USE OUTDOOR EXTENSION CORDS. When

tool is used outdoors, use only extension cords

with approved ground connection that are intended for use outdoors and so marked.

KEEP BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback.

KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Do not reach

undemeath work or around or under the blade

while blade is rotating. Do not attempt to remove cut matedal when blade is moving.

,_ WARNING: Blades coast after turn off.

NEVER USE IN AN EXPLOSIVE ATMO- SPHERE. Normal sparking of the motor could

ignite fumes. INSPECT TOOL CORDS PERIODICALLY and if

damaged, have repaired by a qualified service technician at a Sears store. Stay constantly

aware of cord location and keep it well away from the rotating blade.

INSPECT EXTENSION CORDS PERIODI- CALLY and replace if damaged.

KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth

when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents.to

clean tool. STAY ALERT AND EXERCISE CONTROL.

Watch what you are doing and use common sense. Do not operate tool when you are tired.

Do not rush.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended

function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditionsthat may affect itsoperation. A guard or other part that is damaged must be properly repaired or replaced by a qualified service technician at a Sears store to avoid risk of personal injury.

DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches

replaced by a qualified service technician at a

Sears store.

GUARD AGAINST KICKBACK. Kickback occurs

when the blade stalls rapidlyand workpiece is

driven back towards the operator. It can pullyour hand into the blade resulting in serious personal injury. Stay out of blade path and turn switch off immediately ifblade binds or stalls.

USE THE FENCE. Always use the fence when cutting.

SUPPORT LONG WORKPIECES. To minimize

dsk of blade pinching and kickback, always

support longworkpieces.

RULES FOR SAFE OF_iiflATIUN:{(;OntlnUe¢l}

m BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade

washers or blade bolts that are defective or

incorrect. The maximum blade capacity of your

saw is 10 in. (254 mm).

USE RECOMMENDED ACCESSORIES. The use of improper accessories may cause riskof

injury. NEVER STAND ON TOOL. Sedous injury could

occur ifthe tool is tipped or if the blade is unin- tenUonally contacted.

POLARIZED PLUGS. To reduce the riskof electdc shock, this tool has a poladzed plug (one blade is wider than the other). This plugwill fit in

a polarized outlet only one way. If the plug does

not fit fully in the outlet, reverse the plug. If itstill

does not fit, contact a qualified electrician to

install the proper outlet. Do not change the plug in any way.

NEVER LEAVE TOOL RUNNING UNAT-

TENDED. TURN THE POWER OFF. Do not

leave tool until it comes to a complete stop,

AVOID CUTTING NAILS. Inspect for and

remove all nails from lumber before cutting. NEVER TOUCH BLADE or other moving parts

during use. NEVER START A TOOL WHEN THE BLADE IS

IN CONTACT WITH THE WORKPIECE. DO NOT OPERATE THIS TOOL WHILE UN-

DER THE INFLUENCE OF DRUGS, ALCOHOL, • OR ANY MEDICATION.

SECURE WORK. Use clamps or a vise to hold work when practical. It's safer than using your hand and itfrees both hands to operate tool.

REPLACEMENT PARTS. All repairs, whether electrical or mechanical, should be made by qualified service technician at a Sears store.

WARNING: When servicing use only identical Craftsman replacement parts. Use of any other •

parts may create a hazard or cause product damage. • NEVER USE A DULL SAW BLADE or one that

does not have sufficient set. DO NOT REMOVE THE SAW'S BLADE

GUARDS. Never operate the saw with any guard or cover removed. Make sure all guards are operating properly before each use.

MAKE SURE THE MITER TABLE AND SAW- ARM (BEVEL FUNCTION) ARE LOCKED IN

POSITION BEFORE OPERATING YOUR SAW. Lock the miter table by securely tightening the

miter lock handle. Lock the saw arm (bevel function) by securely tightening the bevel look

knob. NEVER PERFORM ANY OPERATION "FREE-

HAND". Always place the workpiece to be cut on the miter table and position it firmly against the

fence as a backstop.

• ALWAYS USE A CLAMP to secure the

workpiece when possible.

• NEVER hand holda workpiece that istoo small to be clamped. Keep hands clear of the no hands zone.

NEVER reach behind, under, or within three inches of the blade and its cutting path with your

hands and fingers for any reason. NEVER stand or have any part of your body in

line withthe path ofthe saw blade. ALLOW THE MOTOR TO COME UP TO FULL

SPEED before starting a cut. ALWAYS release the power switch and allow the

saw blade to stop rotating before raising it out of the workpiece.

NEVER reach to pick up a workpiece, a piece of

scrap, or anything else that is in or near the cutting path of the blade.

NEVER leave the miter saw unattended while

connected to a power source.

FIRMLY CLAMP OR BOLT your miter saw to a

workbench or table. The most comfortable saw table height is 39 inches or at approximately hip

height. AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slipcould cause your hand to move into the blade. ALWAYS

make sure you have good balance. NEVER operate your miter saw on the floor or in a crouched position.

ALWAYS PROVIDE ADEQUATE ROOM AND SUPPORT for crosscutting longworkpieces.

NEVER USE A LENGTH STOP ON THE FREE SCRAP END OF A CLAMPED WORKPIECE.

NEVER hold onto or bind the free scrap end of the workpiece in any operation, if a work clamp

and length stop are used together, they must both be installed on the same side of the saw

table to prevent the saw from catching the loose end and kicking up.

RULES FOR SAFI| OPF.HATIUN |uontnnueo!

DO NOT TURN THE •OTOR SWITCH ON AND OFF RAPIDLY. This could cause the saw blade to loosen and could create a hazard. Should this

ever occur, stand clear and allow the saw blade

to come to a complete stop. Disconnect your saw

from the power supply and securely retighten the blade bolt.

NEVER cut more than one piece at a time. DO NOT STACK more than one workpiece on the

saw table at a time. IF ANY PART OF THIS MITER SAW IS MISS-

ING or should break, bend, or fail inany way, or should any electrical component fail to perform properly, shut off the power switch, remove the

miter saw plug from the power source and have

damaged, missing, or failed parts replaced

before resuming operation.

SAVE THESE INSTRUCTIONS

• ALWAYS STAY ALERT! Do not allow familiarity

(gained from frequent use of your saw) to cause a careless mistake. ALWAYS REMEMBER that

a careless fraction of a second is sufficientto inflict severe injury.

• MAKE SURE THE WORK AREA HAS AMPLE

LIGHTING to see the work and that no obstruc-

tions will interfere with safe operation BEFORE

performing any work using your saw.

• ALWAYS TURN OFF SAW before disconnecting it, to avoid accidental starting when re-connect-

ingto power supply.

• SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you

loan someone this tool, loan them these instruc- tions also.

Arbor The shaft on which a blade orcutting tool is mounted.

Bevel Cut A cutting operation made withan angled blade.

Crosscut A cutting or shaping operation made across the grain

of the workpiece.

Compound Miter Cut A compound miter cut is a cut made using a miter angle and a bevel angle at the same time.

Freehand

Performing a cut without using a fence, miter gage, fixture, work clamp, or other proper device to keep the workpiece from twisting or moving during the cut.

Gum

A sticky, sap based residue from wood products.

Miter Cut

A cutting operation made with the blade at any angle

other than 90 degrees.

---Resin A sticky, sap ba_sesubstance that has hardened,

Revolutions Per Minute (RPM) The number ofturns completed by a spinning object

in one minute.

Saw Blade Path

The area over, under, behind, or in front of the blade.

As it applies to the workpiece, that area which will be, or has been, cut by the blade.

Set The distance that the tip of the sawblade tooth is bent

(or set) outward from the face of the blade. Throw-Back

Throwing of a workpiece in a manner similar to a

kickback. Usually associated with a cause other than

the kerr closing, such as a workpiece not being

against the fence, being dropped into the blade, or being placed inadvertently incontact with the blade.

Through Sawing Any cutting operation where the blade extends completely through the thickness of the workpiece.

Workplece The item on which the cuttingoperation is being done.

The surfaces of a workpiece are commonly referred to

as faces, ends, and edges. Zero Clearance Throat Plate

A plastic throat plate inserted in the miter table that

allows for blade clearance. When you make your first cut with your compound miter saw, the saw blade cuts

a slot through the throat plate the exact width of the blade. This provides for a zeroclearance kerf that

minimizes workpiece tear-out.

No Hands Zone

The area between the marked lines on the left and

right side of the miter table base. This zone is identified by no hands zone labels placed inside the

marked lines onthe mitertable base.

BladeDiameter BladeArbor

NoLoadSpeed

Rating Input NetWeight

10 in. (254 mm)

5/8 in. (16 mm)

5000 RPM

120 Volts, 60 Hz-AC Only

15 Amperes

32.3 lb. (14.7 kg.)

Cutting Capacity with Miter at 0°/Bevel 0°:

Maximum Width 5-9/16 in. (141.3 ram) W x 2-9/32 in. (57.9 mm) T

Maximum Thickness 3-9/16 in. (90.5 mm) T x 4 in. (101.6 mm) W

Maximum Cutting Capacity with Miter at 45°/Bevel 0°:

3-15/16 in. (100 mm) W x 2-9/32 in. (57,9 mm) T

Maximum Cutting Capacity with Miter at 45°/Bevel 45°:

4 in, (101,6 mm) W x 1-9/16 in. (39,7 mm) T

Your Compound Miter Saw has been shipped completely assembled except for the blade, miterlook

handle, and dust guide.

,_ WARNING: If anyparts are missing, do not

operate this tool until the missing parts are replaced. Failure to do so could result in possible

sedous personal injury,

• Remove all loose parts from the carton. Separate

and check withthe list of loose parts. See Figure 2.

• Remove the packing materials from around your

saw.

Carefully lift saw from the carton and place it on a level work surface. Although small, this saw is heavy. To avoid back injury, get help when

needed.

Do not discard the packing matedals until you have carefully inspected the saw, identifiedall

loose parts, and satisfactodly operated your new

saw.

• Your saw has been shipped with the saw arm

looked in the down position. To release saw arm, push down on top of saw arm and pull out the lock pin. See Figure 4.

• Lift the saw arm by the handle. Hand pressure

should remain on the saw arm to prevent sudden

rise upon release of the lock pin.

• Examine all parts to make sure no breakage or

damage has occurred dudng shipping.

If any parts are damaged or missing, do not attempt to plug in the power cord and turn the switch on until the damaged or missing parts are obtained and are installed correctly.

The following labels are on the miter saw with loca- tions indicated.

Restorelowerbladeguard

andsecurelytightenscrew

beforeuse

I W-"I :-J_1ib,"]

CRAFTSMRN ,.m.,,.,.

I "1 10 inch Miter Saw

CAUTION:FoRSAFE OPERATION,SEE OWNER'S MANUAL

WEAR EYE PROTECTION,WHEN SERVICING, USE ONLY19ENTICALCRAFTSMAN

REPLACEMENTPARTS. _i

MODEL 315.235360 SER, NO.

MADE IN Talwan NRIL_ SEARS, ROEBUCK AND CO. ST#,1:OI_ lr_t I I

120VOLTS60FtzAC0NLY15A

yourownsaloty: ADVERTENCIA:

tReed owneremonsalbefo;'eoporatlnoreltersaw Pareuuproplaosgurldad

• Weareyeprotection, leaelmanualdofasaaflo

• Keepbandsout ofputhofsawblade, antesdeosarla sierra

• gonotoputathsawwithoutguardsInplace, inglethdoru.

• Donotperformanyoperationfreehand.

• Neverreacharoundthesawblade.

• Turnofftoolandwaitforsawbladeto stop beforereevingwed(pieceorchang]ngsettings.

• Disconnectthesawfromthepowersourcebefell

changingbladeorservicing.

• DonotexposetorainoruseIndampplaces.

Fig. 1

The following items are included with your Compound Miter Saw:

• Saw Blade - 10 in. (254 mm) • 5 mm Hex Key (Allen wrench)

• Miter Lock Handle • 8 mm Hex Key (Allen wrench)

• Dust Guide • Owner's Manual

• Blade Wrench • Warranty Registration

__8 mmHEXKEY

(_ (ALLENWRENCH)

_5 mmHExKEY

(ALLENWRENCH)

_DLE

SAWBLADE

Fig. 2

WARNING: The use of attachments or accessories not listed might be hazardous and could

The following tools (not included) are needed for checking adjustments of your saw or for installing the blade:

FRAMINGSQUARE

cause serious personal injury.

_ 17Jm COMBINATIONWRENC_

10mmCOMBINATIONWRENCH

SQUARE

8 mm COMBINATIONWRENCH

PHILUPSSCREWDRIVER

KNOW YOUR COMPOUND MITER SAW

See Figure 3.

Before attempting to use your saw, familiarize yourself with all operating features and safety requirements.

_lb WARNING: Do not allow familiarity with your

saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict

severe injury.

15 AMP MOTOR

Your saw has a powerful 15 amp motor with sufficient power to handle tough cuffing jobs. It is made with all..

ball bearings, and has externally accessible brushes

for ease of servicing,

10 IN. (254 MM) BLADE

A 10 in. (254 mm) saw blade is included with your

compound miter saw. It will cut materials up to 3-9/16 in. (90.5 mm) thick or 5-9/16 (141.3 ram) wide, depending upon the thickness of the material and the setting at which the cut is being made.

CUTTING CAPACITIES

When the miter angle (miter table) Is set at O° and the bevel angle is set at O°:

Your saw will cut materials up to a maximum width of 5-9/16 in. (141.3 ram) wide X 2-9/32 in.

(57.9 mm) thick, Itwill cut materials up to a maximum thickness of

3-9/16 in. (90,5 mm) thick X 4 in, (101.6 mm) wide. When the miter angle (miter table) is set at 45° and

the bevel angle Is set at O°:

Your saw will cut materials up to a maximum of 3-15/16 in. (100 mm) wide X 2-9/32 in. (57.9 mm)

thick.

When the miter angle (miter table) Is sat at 0° end the bevel angle Is set at 45°:

Your saw will cut materials up to a maximum of 5-9/16 in. (141,3 mm) wide X 1-9/16 in, (39.7 mm)

thick. When the miter angle (miter table) is Set at 45° and

the bevel angle Is set at 45°: Your saw will cut materials up to a maximum of

4 in. (101,6 mm) wide X 1-9/15 in, (39.7 ram) thick,

MITER

TABLEFRAME

BEVEL

UPPER

BLADEGUARD

DUSTGUIDE

SAWARM

SWITCH

SWITCHTRIGGER

, LOWER

BLADEGUARD

NOHANDS

ZONELABEL

"NOHANDSZONE"

BOUNDARYLINE

MITERSCALE

ZEROCLEARANCE

THROATPLATE

PosmvESTOP(S)

CONTROLARM

, MITER

LOCKPLATE

MITER

LOCKHANDLE

Fig. 3

I i_TM,,IIJMiJ=1,iq,,,-]l

CARRYING HANDLE

See Figure 4.

For convenience when carrying or transportating your miter saw from one place to another, a carrying handle has been provided ontop of the saw arm as

shown in figure 4. To transport, turn off and unplug your saw, then lower the saw arm and lock it in the

down position, Lock saw arm by depressing the lock pin.

CARRYING

HANDLE

SAW ARM

LOCK

SPINDLE LOCK BUTTON

See Figure 5.

A spindle lock button has been provided forlocking the spindle which stops the rotation of the blade in

your saw. Depress and hold the lock button while installing, changing, or removing blade.

SPINDLELOCKBuI"rON

LOCK-OFF

SWITCH•

TRIGGER

MITERLOCK

HANDLE

SAWARM

LOCKEDINDOWNPosmoN Fig. 4

MITER LOCK HANDLE

See Figure 4.

The miter lock handle securely locks your saw at desired miter angles.

LOCK-OFF LEVER

See Figure 5.

The switch trigger is equipped with a lock-off lever to

reduce the possibilityof accidental starting. The lock- off lever must be slid back away from the switch

trigger in order to turn saw on. Once the saw ison,

file lock-off lever can be released. The spring loaded

lever will spring_back into the lock-off position when

the switch trigger is released.

Fig. 5

TRIGGER LOCK

See Figure 6,

To prevent unauthorized use of your compound miter saw, we suggest that you disconnect it from the power

supply and lock the switch in the off position. To lock the switch, install a padlock through the hole in the switch trigger. A lock with a shackle up to 13/64 in.

(5 ram) diameter may be used. When the lock is

installed and locked, the switch is inoperable. Store the padlock key in another location.

TRIGGER

PADLOCK

Fig. 6

POSITIVE STOPS ON MITER TABLE

Positive stops have been provided at 0°, 22-1/2 ° and 45°. The 22-1/2 ° and 45° positive stops have been provided on both the left and right side of the miter

table.

BEVEL LOCK KNOB

The bevel lock knob securely locks your compound miter saw at desired bevel angles. Positive stop adjustment screws have been provided on each side of the saw arm. These adjustment screws are for

making fine adjustments at 0° and 45 °. Se pages 17 and 18.

ELECTRIC BRAKE

_--7-1/8"---_9-7/8"--

;_ .,

,-IJI

T ] I 7116"DIA. -_

An electdc brake has been provided to quickly stop blade rotation after the switch is released.

FENCE

The fence Onyour compound miter saw has been provided to hold your workpiece securely against when making all cuts.

SELF-RETRACTING LOWER BLADE

GUARD

The lower blade guard is made of shock-resistant, see-through plastic that provides protection from each side of the blade. It retracts over the upper blade

guard as the saw is lowered into the workpiece. MOUNTING HOLES

See Figure 7.

Your compound miter saw should be permanently mounted to a firm supporting surface such as work-

bench. Four 7116 in. (11 mm) bolt holes have been provided in the saw base for this purpose. Each of the

four mounting holes should be bolted securely using

7/16 in. (11 mm) machine bolts, lock washers, and hex nuts (not included). Bolts should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench.

Tighten all four boltssecurely. The hole pattern for an 18 in. (457 mm) x 24 in.

(610 mm) workbench is shown in Figure 7. Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the work-

be_ch to the floor before operating.

Fig. 7

ELECTRICAL CONNECTION

Your saw has a precision builtelectdc motor. It should be connected to a power supply that Is 120 volts, 60 Hz, AC only (normal household current). Do not

operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor

will overheat. If your tool does not operate when plugged into an outlet, double-check the power

supply.

_. WARNING: The operation of any saw can

result in foreign objects being thrown into your eyes, which can result in severe eye damage.

Before starting power tool operation, always wear safety goggles or safety glasses with side

shields and a full face shield when needed. We recommend wide vision safety mask for use over

eyeglasses or standard safety glasses with side shields.

_k WARNING: Do not attempt to modify this tool or

create accessories not recommended for use with this tool. Any such alteration or modification

is misuse and could result in a hazardous condition leading to possible serious personal

injury.

_L WARNING: ,_lways make sure your compound

miter saw is securely mounted to a workbench or

an approved workstand. Failure to do so could

result in an accident resulting in possible sedous personal injury.

+ 26 hidden pages