Craftsman 31522210 Owner’s Manual
Owner's Manual
II:RRFTSMRN'I
ROUTER MOUNTING KIT
FOR MODEL NOS, 9-22811 AND 9-22185 TABLE SAWS
Item No.
_922210
I
Sava this manual for
future reference.
,A CAUTION: Read and follow
all Safety Rules and Operating
Instructions before first use of
this product.
Customer HeEpLine: 1-800-932-3188
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
972000-724
8-01
• SAFETY
• UNPACKING
• ASSEMBLY
• USE
READ ALL INSTRUCTIONS
• READ THESE INSTRUCTIONS AND INSTRUC-
TIONS FOR YOUR TABLE SAW THOROUGHLY
BEFORE USING ACCESSORY.
i KNOW YOUR POWER TOOL. Read the owner's
manual for your Table Saw carefully. L.eam the
saw's applications and limitations as well as the
specific potential hazards related to this tool.
• KEEP THE WORK AREA CLEAN. Cluttered work
areas and work benches invite accidents. DO NOT
leave tools or pieces of wood on the saw while it is
in operation.
• ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
• ALWAYS DISCONNECT SAW FROM POWER
SUPPLY BEFORE MAKING ADJUSTMENTS OR
ADDING ACCESSORIES, Make sure the switch is
off when reconnecting to power supply.
_lk Look for this symbol to point out important safety precautions, it
means attention!I! Your safety is involved.
i
ALWAYS FEED WORKPIECE AGAINST THE
ROTATION OF THE CUTTER.
M
DO NOT USE AWKWARD HAND POSITIONS.
ii
KEEP FINGERS AWAY from the revolving cutter,
and use fixtures when necessary.
ALWAYS USE THE DUST COVER for overhead
guarding.
DO NOT REMOVE JAMMED CUTOFF PIECES
until cutter or blade has Stopped and tool has bean
disconnected from power source.
HOLD THE WORKPIECE FIRMLY AGAINST THE
TABLE.
ALWAYS USE THE SAW'S MASTER SWITCH
TO TURN THE ROUTER ON AND OFF.
I
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you
loan someone this accessory, loan them these
instructions also.
ROUTER MOUNTING KIT
Read these instructions completely before mounting
your router to the accessory table of your Craftsman
922811 or 922185 table sew.
A router mounted on the accessory table will provide
expanded capabilities for making rabbets, grooves,
chamfers, dovetails, and mortise and tenon joints.
This router mounting kit wi[[ accommodate most
Craftsman reuters.
If used and stored proper[y, the muter mounting kit
will give you years of dep_ndable, trouble-free perfor-
mance.
_1= WARNING: Before attempting to use your
muter mounting kit. familiarize yourself with all
operating features and safety requirements.
WARNING:
result In severe eye damage. Before beginning tool operation, always wear safety goggles or
safety glasses with side shields and a fullface shield when needed. We recommend Wide Vision
The operation of any tool can result In foreign objects being thrown into your eyes. which can
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at
Sears Retail Stores.
UNPACKING THE ROUTER MOUNTING KIT
Included in the router mounting kit are a mounting
plate, two guide fences with guide blocks, a guard/
dust cover with pivot assembly, 5 throat plates, plus
necessary brackets and hardware required to mount a
router to the accessory table of the Craftsman 922811
or 922185 table saw.
Separate ell the parts and check the parts against the
parts list. See Figure I.
During assembly and installation you will need a
phillips screwdriver, an adjustable wrench, end
possibly a hex key.
_k WARNING: Use recommended accessories.
The use of improper accessories may create a
risk of injury. Do not use this router mounting kit
for any purpose other than as an accessory to
the recommended table saw. Fsilur'e to heed this
warning can result in serious personal injury or
damage to the accessory.
2
5/16 In.
THROAT PLATES
ROUTER
MOUNTINGPLATE
LOOSE PARTS
Check the parts with the list. If any of the parts are
missing, delay the assembly until you have obtained
the missing part.
Description Quantity
Guide Fence with Guide Block ......................... 2
Knob Bolt (5/16-18 x 1/2 in. for Guide Fence)., 4
5/16 in. Washer ................................................. 5
5/16 in. T-Nut (Special) ..................................... 6
Spacer ............................................................... 1
Post ................................................................ 1
Guard/Dust Cover with Pivot Assembly ........... I
Throat Plates .................................................... 5
Router Mounting Plate ...................................... 1
Table Clamping Bracket ................................... 1
Knob Bolt (5/16-18 x 3/4 in. for Table Clamp) .. 1
Screw (MS x 24 mm fiat head screw) .............. 4
Screw (#10-32 x 1/2 in, flat head) .................... 3
Screw (#5/16-18 x 3/4 in. fiat head) ................. 3
Screw (#1/4-20 x 1/2 in. flat head) .................. 4
GUIDE FENCE ASSEMBLY
• Unplugthe saw,
WARNING: Unplugthe powersupplycordof
the saw beforemountingthis kit.Failure to
unplugyoursew couldresultin aooiclental
startingcausing possibleseriouspersonalinjuw.
WARNING: The saw's motor cord must be
A
disconnected from the receptacJe on saw when
using this kit. The power cord of the muter must
be plugged into the receptacle on the saw. The
saw's master switch must be used to turn the
router On and Off, Failure to do so could result
in serious personal injury.
• Lift the blade guard end place the rip fence against
the sew blade and lock the rip fence in place. This
will insure that the rip fence remains square while
instetling the first t-nut. See Figure 2.
3
Fig. 1
Loading...