Craftsman 315218280 Owner’s Manual
PERATOR'S AL
10 in. TABLE SAW
Model No.
315.218280
,&
WARNING: To reduce the risk of injury, the
user must read and understand the operator's
manual before using this product.
Customer Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
987000-344
9-1-08 (REV:00)
Save this manual for future reference
[] Warranty ........................................................................................................................................................................... 2
[] introduction ...................................................................................................................................................................... 2
[] General Safety Rules ..................................................................................................................................................... 3-4
[] Specific Safety Rules ..................................................................................................................................................... 4-5
[] Symbols ......................................................................................................................................................................... 6-7
[] Electrical ........................................................................................................................................................................... 8
[] Glossary of Terms ............................................................................................................................................................. 9
[] Features ..................................................................................................................................................................... 10-12
[] Tools Needed ................................................................................................................................................................. 13
[] Loose Parts .................................................................................................................................................................... 14
[] Assembly ................................................................................................................................................................... 15-19
[] Operation ................................................................................................................................................................... 19-32
[] Adjustments ............................................................................................................................................................... 33-35
[] Maintenance ................................................................................................................................................................... 36
[] Accessories .................................................................................................................................................................... 36
[] Troubleshooting ......................................................................................................................................................... 37-38
[] Exploded View ........................................................................................................................................................... 39-46
[] Parts Ordering/Service ...................................................................................................................................... Back Page
ONE YEAR FULL WARRANTY ON CRAFTSMAN TOOL
If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of purchase. Call
1-800-4-MY-HOME ® to arrange for free repair. If this tool is used for commercial or rental purposes, this warranty will
apply for only ninety days from the date of purchase. This warranty applies only while this product is in the United States.
This warranty gives you specific legal nghts, and you may also have other nghts which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
_IL WARNING: Read and understand all instruc-
tions. Failure to follow all instructions listed below,
may result in electric shock, fire and/or serious
personal injury.
READ ALL INSTRUCTIONS
[] KNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the saw's applications and
limitations as well as the specific potential hazards
related to this tool.
[] GUARD AGAINST ELECTRICAL SHOCK BY PRE-
VENTING BODY CONTACT WiTH GROUNDED
SURFACES. For example, pipes, radiators, ranges,
refrigerator enclosures.
[] KEEP GUARDS IN PLACE and in good working order.
[] REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
[] KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents. DO NOT leave tools or
pieces of wood on the saw while it is in operation.
[] DO NOT USE IN DANGEROUS ENVIRONMENTS.
Do not use power tools in damp or wet locations or
expose to rain. Keep the work area well lit.
[] KEEP CHILDREN AND ViSiTORS AWAY. All visitors
should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
[] MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
[] DON'T FORCE TOOL. It will do the job better and
safer at the feed rate for which it was designed.
[] USE RIGHT TOOL. Don't force the tool or attachment
to do a job it was not designed for. Don't use it for a
purpose not intended.
[] USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. A
wire gauge size (A.W.G.) of at least 14 is recommended
for an extension cord 25 feet or less in length. If in
doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
[] DRESS PROPERLY. Do not wear loose clothing,
gloves, neckties, or jewelry. They can get caught
and draw you into moving parts. Rubber gloves and
nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
[] ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
[] SECURE WORK. Use clamps or a vise to hold work
when practical. It's safer than using your hand and
frees both hands to operate tool.
[] DON'T OVERREACH. Keep proper footing and
balance at all times.
[] MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
[] DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
[] AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
[] USE RECOMMENDED ACCESSORIES. Consult the
operator's manual for recommended accessories. The
use of improper accessories may risk injury.
[] NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting tool is unintention-
ally contacted.
[] CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that
is damaged must be properly repaired or replaced by
an authorized service center to avoid risk of personal
injury.
[] USE THE RIGHT DIRECTION OF FEED. Feed work
into a blade or cutter against the direction of rotation of
blade or cutter only.
[] NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Don't leave tool until it
comes to a complete stop.
[] PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
[] PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
[] DO NOT ABUSE CORD. Never yank cord to discon-
nect from receptacle. Keep cord from heat, oil, and
sharp edges.
[] WHEN OPERATING A POWER TOOL OUTSIDE, USE
AN OUTDOOR EXTENSION CORD MARKED "W-A"
OR "W". These cords are rated for outdoor use and
reduce the risk of electric shock.
[] ALWAYS KEEP THE BLADE GUARD AND RIVING
KNIFE/SPREADER/SPLITTER IN PLACE and in
working order.
[] KEEP BLADES CLEAN, SHARP, AND WITH SUF-
FICIENT SET. Sharp blades minimize stalling and
kickback.
[] KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath
work or around or over the blade while blade is rotat-
ing. Do not attempt to remove cut material when blade
is moving.
[]
BLADE COASTS AFTER BEING TURNED OFF.
[] NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
[] INSPECT TOOL CORDS PERIODICALLY. If damaged,
have repaired by a qualified service technician at
an authorized service facility. The conductor with
insulation having an outer surface that is green with
or without yellow stripes is the equipment-ground-
ing conductor. If repair or replacement of the electric
cord or plug is necessary, do not connect the equip-
ment-grounding conductor to a live terminal. Repair
or replace a damaged or worn cord immediately. Stay
constantly aware of cord location and keep it well away
from the rotating blade.
[] INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
[] GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole
electrical receptacle.
[] CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not com-
pletely understood or if in doubt as to whether the tool
is properly grounded.
[] USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs
and 3-pole receptacles that accept the tool's plug.
[] DO NOT MODIFY the plug provided, if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
[] KEEP TOOL DRY, CLEAN, AND FREE FROM OIL
AND GREASE. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any solvents to clean tool.
[] STAY ALERT AND EXERCISE CONTROL. Watch
what you are doing and use common sense. Do not
operate tool when you are tired. Do not rush.
[] DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
[] USE ONLY CORRECT BLADES. Do not use blades
with incorrect size holes. Never use blade washers or
blade bolts that are defective or incorrect. The maxi-
mum blade capacity of your saw is 10 in. (254 mm).
[] BEFORE MAKING A CUT, BE SURE ALL ADJUST=
MENTS ARE SECURE.
[] BE SURE BLADE PATH IS FREE OF NAILS. Inspect
for and remove all nails from lumber before cutting.
[] NEVER TOUCH BLADE or other moving parts during
use.
[] NEVER START A TOOL WHEN ANY ROTATING
COMPONENT (S (N CONTACT W(TH THE WORK-
PIECE.
[] DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
[] WHEN SERVICING use only identical replacement
parts. Use of any other parts may create a hazard or
cause product damage.
[] USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories
that are not listed may cause the risk of personal
injury. Instructions for safe use of accessories are
included with the accessory.
[] DOUBLE CHECK ALL SETUPS. Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
[] FIRMLY BOLT THE SAW TO A WORK BENCH OR
LEG STAND at approximately waist height.
[] NEVER OPERATE THE SAW ON THE FLOOR.
[]
GUARD AGAINST KICKBACK. Kickback occurs
when the blade stalls rapidly and workpiece is driven
back towards the operator. It can pull your hand into
the blade resulting in serious personal injury. Stay out
of blade path and turn switch off immediately if blade
binds or stalls.
[] USE RIP FENCE. Always use a fence or straight edge
guide when ripping.
[] SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
[] REMOVE ALL FENCES AND AUXILIARY TABLES
before transporting saw. Failure to do so can result in
an accident causing possible serious personal injury.
[] ALWAYS USE BLADE GUARD, SPREADER, AND
ANTI-KICKBACK PAWLS on all "through-sawing"
operations. Through-sawing operations are those in
which the blade cuts completely through the workpiece
as in ripping or cross cutting. Keep the blade guard
down, the anti-kickback pawls down, and the spreader
in place over the blade.
[] ALWAYS SECURE WORK firmly against the rip fence
or miter gauge. NEVER use the rip fence during the
same operation as the miter gauge.
[] ALWAYSUSEAPUSH STICK FOR RIPPING
NARROW STOCK. A push stick is a device used to
push a workpiece through the blade instead of using
your hands. Size and shape can vary but the push
stick must always be narrower than the workpiece to
prevent the push stick from contacting the saw blade.
When ripping narrow stock, always use a push stick,
so your hand does not come close to the saw blade.
Use a featherboard and push blocks for non-through
CutS.
[] NEVER perform any operation "freehand" which
means using only your hands to support or guide the
workpiece. Always use either the rip fence or miter
fence to position and guide the work.
[] NEVER stand or have any part of your body in line
with the path of the saw blade.
[] NEVER reach behind, over, or within three inches of
the blade or cutter with either hand for any reason.
[] MOVE THE RIP FENCE out of the way when cross
cutting.
[] DO NOT USE THE MITER GAUGE AND RIP FENCE
during the same operation.
[] NEVER use rip fence as cutoff gauge when cross
cutting.
[] NEVER attempt to free a stalled saw blade without
first turning the saw OFF and disconnecting the saw
from the power source.
[] PROVIDE ADEQUATE SUPPORT to the rear and
sides of the saw table for wide or long work pieces.
[] AVOID KICKBACKS (work thrown back toward you)
by:
a)
Keeping blade sharp.
b)
Keeping rip fence parallel to the saw blade.
c)
Keeping spreader, anti-kickback pawls, and
blade guard in place and operating.
d)
Not releasing the work before it is pushed all the
way past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or does
not have a straight edge to guide along the fence.
[]
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an autho-
rized service center to avoid risk.
[] AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your
hand to move into the cutting tool.
[] USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instruc-
tions for safe use of accessories are included with the
accessory.
[] MAKE SURE THE WORK AREA HAS AMPLE LIGHT=
ING to see the work and that no obstructions will inter-
fere with safe operation BEFORE performing any work
using the table saw.
[] ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
[] ONLY USE BLADES within the thickness range
stamped on the spreader/riving knife.
[] THIS TOOL should have the following markings:
a) Wear eye protection.
b) Use saw blade guard and spreader/riving knife for
every operation for which it can be used, including
all through sawing.
c) Keep hands out of the line of saw blade.
d) Use a push stick when required.
e) Pay particular attention to instructions on reducing
risk of kickback.
f) Do not perform any operation freehand.
g) Never reach around or over the saw blade.
[] SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
_ WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning.Proper
interpretationofthesesymbolswillallowyoutooperatethetoolbetterandsafer.
SYMBOL
NAME DESIGNATION/EXPLANATION
V
A
Hz
W
min
no
[]
.../min
@
Volts
Amperes
Hertz
Watt
Minutes
Alternating Current
Direct Current
No Load Speed
Class II Construction
Per Minute
Wet Conditions Alert
Voltage
Current
Frequency (cycles per second)
Power
Time
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
Do not expose to rain or use in damp locations.
0
A
Read The Operator's Manual
Eye Protection
Safety Alert
No Hands Symbol
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Always wear safety goggles or safety glasses with side
shields and a full face shield when operating this product.
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
6
Thefollowingsignalwordsandmeaningsareintendedto explainthelevelsofriskassociatedwiththisproduct.
SYMBOL SIGNAL MEANING
DANGER:
,_ WARNING:
CAUTION: result in minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in
SERVICE
Servicing requires extreme care and knowledge and
should be performed only by a qualified service techni-
cian. For service we suggest you return the product to
your nearest SEARS PARTS AND REPAIR SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
,_ WARNING:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may
property damage.
_lb WARNING: To avoid serious personal injury, do not
attempt to use this product until you read thoroughly
and understand completely the operator's manual. If
you do not understand the warnings and instructions
in the operator's manual, do not use this product.
Call the Craftsman Consumer Helpline at 1-800-932-
3188 for assistance.
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
EXTENSION CORDS
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept the
tool's plug. When using a power tool at a considerable
distance from the power source, use an extension cord
heavy enough to carry the current that the tool will draw.
An undersized extension cord will cause a drop in line
voltage, resulting in a loss of power and causing the motor
to overheat. Use the chart provided below to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter's Laboratories
(UL) should be used.
_*Ampere rating (on tool data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.}
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 --
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension
cord that is designed for outside use. This isindicated by
the letters "W-A" or "W" on the cord's jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
A
WARNING: Keep the extension cord clear of the
working area. Position the cord so that it will not get
caught on lumber, tools or other obstructions while
you are working with a power tool. Failure to do so
can result in serious personal injury.
A
WARNING: Check extension cords before each
use. If damaged replace immediately. Never use tool
with a damaged cord since touching the damaged
area could cause electrical shock resulting in serious
injury.
SPEED AND WIRING
The no-load speed of this tool is approximately 5,000 rpm.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor's horsepower rating. A line intend-
ed only for lights cannot properly carry a power tool motor.
Wire that is heavy enough for a short distance will be too
light for a greater distance. A line that can support one
power tool may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of a malfunc-
tion or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This tool isequipped with an electric cord having
an equipment-grounding conductor and a grounding plug.
The plug must be plugged into a matching outlet that is
properly installed and grounded in accordance with all lo-
cal codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
,_1I_ WARNING: Improper installation of the ground-
ing plug is able to result in a risk of electric shock.
When repair or replacement of the cord is required,
do not connect the grounding wire to either flat blade
terminal. The wire with insulation having an outer
surface that is green with or without yellow stripes is
the grounding wire.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 volt circuit and
has a grounding plug similar to the plug illustrated in fig-
ure 1. Only connect the product to an outlet having the same
configuration as the plug. Do not use an adapter with this
product.
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It
should be connected to a power supply that is 120 V, AC
only (normal household current}, 60 Hz. Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the saw does not operate when plugged into an outlet,
double check the power supply.
J
GROUNDING
PiN 120V GROUNDED OUTLET
Fig. 1
8
Anti=KickbackPawls (radial arm and table saws}
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Arbor
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with the blade at any angle
other than 90° to the table surface.
Chamfer
A cut removing a wedge from a block so the end (or part
of the end) is angled rather than at 90° .
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
A cutting or shaping operation made across the grain or
the width of the workpiece.
Cutter Head (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives.
The blades or knives remove material from the workpiece.
Dado Cut
A non-through cut which produces a square-sided notch
or trough inthe workpiece (requires a special blade).
Featherboard
A device used to help control the workpiece by guiding it
securely against the table or fence during any ripping
operation.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Gum
A sticky, sap-based residue from wood products.
Heel
Alignment of the blade to the fence.
Kerr
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls,
throwing the workpiece back toward operator.
Leading End
The end of the workpiece pushed into the tool first.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90 °.
Non=Through Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Pilot Hole (drill presses)
A small hole drilled in a workpiece that serves as a guide
for drilling large holes accurately.
Push Blocks (for jointer planers)
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator's hands well away from the cutterhead.
Push Blocks and Push Sticks (for table saws)
Devices used to feed the workpiece through the saw
blade during cutting operations. A push stick (not a push
block) should be used for narrow ripping operations.
These aids help keep the operator's hands well away from
the blade.
Resaw
A cutting operation to reduce the thickness of the
workpiece to make thinner pieces.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in
one minute.
Ripping or Rip Cut
A cutting operation along the length of the workpiece.
Riving Knife/Spreader/Splitter (table saws}
A metal piece, slightly thinner than the kerf, which helps
keep the kerf open and also helps to prevent kickback.
Saw Blade Path
The area over, under, behind, or in front of the blade. As
it applies to the workpiece, that area which will be or has
been cut by the blade.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Snipe (planers}
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
Throw=Back
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
Workpiece or Material
The item on which the operation is being done.
Worktable
Surface where the workpiece rests while performing a cut-
ting, drilling, planing, or sanding operation.
9
PRODUCT SPECiFiCATiONS
Blade Arbor .............................................................. 5/8 in.
Blade Diameter .......................................................... 10 in.
Blade Tilt ................................................................. 0°- 45°
Rating .......................................... 120 V-, 60 Hz, 15 Amps
ANTFKICKBACK
PAWLS
OUTFEED MITER
SUPPORT GAUGE
SPREADER/
RiViNG KNIFE
No Load Speed .................................... 5,000 r/min. (RPM)
Cutting Depth at 0°: ............................................... 3-1/4 in.
Cutting Depth at 45°: ............................................. 2-3/8 in.
BLADE
GUARD
RiP FENCE
LOCKING
LEVER
CORD
STORAGE
BLADE
WRENCH
STORAGE
BEVEL
SCALE
BEVEL
LOCKING
LEVER
HEiGHT/BEVEL
ADJUSTING
HANDWHEEL
FRONT
RAiL
SWITCH
ASSEMBLY
Fig. 2
10
KNOWYOURTABLESAW
See Figure 2.
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual
as well as a knowledge of the project you are attempt-
ing. Before use of this product, familiarize yourself with all
operating features and safety rules.
ANTI-KICKBACK PAWLS - Kickback is a hazard in which
the workpiece is thrown back toward the operator. The
teeth on the removable anti-kickback pawls point away
from the workpiece. If the workpiece should be pulled
back toward the operator, the teeth dig into the wood to
help prevent or reduce the possibility of kickback.
BEVEL SCALE - The easy-to-read scale on the front of
the cabinet shows the exact blade angle.
BLADE - This saw is provided with a 36-tooth, 10 in.
carbide blade. The blade is raised and lowered with
the height/bevel adjusting handwheel. Bevel angles are
locked with the bevel locking lever.
_k WARNING: Do not use blades rated less than the
speed of this tool. Failure to heed this warning could
result in personal injury.
BLADE GUARD - Always keep the removable blade guard
down over the saw blade for through-sawing cuts.
BEVEL LOCKING LEVER - This lever, placed just under
the saw table surface on the front of the cabinet, locks the
angle setting of the blade.
HEIGHT/BEVEL ADJUSTING HANDWHEEL- Located
on the front of the cabinet, use this handwheel to lower
and raise the blade for height adjustments or blade re-
placement. This handwheel also makes the adjustment for
bevel angles easy.
MITER GAUGE - The miter gauge aligns the wood for
a cross cut. The easy-to-read indicator shows the exact
angle for a miter cut, with positive stops at 90 ° and 45°.
MITER GAUGE GROOVES - The miter gauge rides in the
grooves on the saw table.
OUTFEED SUPPORT - This table extension at the back
of the tool gives the operator additional support when cut-
ting long workpieces.
RIP FENCE - A sturdy metal fence guides the workpiece
and is secured with the locking handle. Grooves run along
the top and sides of the rip fence for use with optional
clamps and accessories.
SCALE - Located on the front rail, the easy-to-read scale
provides precise measurements for rip cuts.
SLIDING TABLE EXTENSION - Located on right side of
the saw table, this table extension gives the operator
additional support when cutting wide workpieces.
SPREADER / RIVING KNIFE - A removable metal piece
of the blade guard assembly, slightly thinner than the saw
blade, which helps keep the kerf open and prevent kick-
back. When in the through sawing, or "up" position, it is
higher than the saw blade and becomes a spreader. When
in the non-through sawing, or "down" position, it is below
the saw blade teeth and becomes a riving knife.
SWITCH ASSEMBLY - This saw has an easy access
power switch located below the front rail. To lock the
switch in the OFF position, remove the switch key from
the switch. Place the key in a location that is inaccessible
to children and others not qualified to use the tool.
11
OPERATING COMPONENTS
The upper portion of the blade projects up through the
table and is surrounded by an insert called the throat
plate. The height of the blade is set with a handwheel on
the front of the cabinet. To accommodate wide panels,
the saw table has rails on each side. Detailed instructions
are provided in the Operation section of this manual for
the basic cuts: cross cuts, miter cuts, bevel cuts, and
compound cuts.
The rip fence is used to position work for lengthwise cuts.
A scale on the front rail shows the distance between the
rip fence and the blade.
It is very important to use the blade guard assembly for all ,_
through-sawing operations. The blade guard assembly
includes: riving knife/spreader/splitter, anti-kickback
pawls, and blade guard.
POWER SWITCH
See Figure 3.
This saw is equipped with a power switch that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
TO TURN YOUR SAW ON:
[] With the switch key inserted into the switch, lift the
switch button to turn ON ( I ).
TO TURN YOUR SAW OFF:
[] Press the switch button down to turn OFF ( 0 ).
TO LOCK YOUR SAW:
[] Press the switch button down.
[] Remove the switch key from the switch and store in a
safe, secure location.
A
WARNING: Always remove the switch key when
the tool is not in use and keep it in a safe place. In
the event of a power failure, turn the switch OFF
( O ) and remove the key. This action will prevent the
tool from accidentally starting when power returns.
,#k
WARNING: Always make sure your workpiece is
not in contact with the blade before operating the
switch to start the tool. Failure to heed this warning
may cause the workpiece to be kicked back toward
the operator and result in serious personal injury.
WARNING: To reduce the risk of accidental start-
ing, always make sure the switch is in the OFF ( O }
position before plugging tool into the power source.
SWITCH SWITCH
ON OFF
12
SW(TCHKEYREMOVED
Fig. 3
Thefollowingtools(notincludedordrawntoscale)areneededformakingadjustments:
_t,l,_,l,_,J,l,l,a,l,l,l,bl,l,l,_
FRAMINGSQUARE
PHiLLiPS
SCREWDRIVER
COMBINATION
SQUARE
FLATBLADE
SCREWDRIVER
Fig. 4
13
Thefollowingitemsareincludedwithyourtablesaw:
A
E
0
6
A. Blade Guard ............................................................ 1
B. Anti-Kickback Pawls ............................................... 1
C. Miter Gauge ............................................................. 1
D. Rip Fence ................................................................ 1
Fig. 5
E. Handle Assembly .................................................... 1
R Push Stick ............................................................... 1
G. Blade Wrench .......................................................... 2
H. Hex Key, 5 mm ........................................................ 1
14
Loading...