Craftsman 31517560 Owner’s Manual

612547-243

SEARS

OWNERS

MANUAL

MODEL NO

315,17560

CAUTION

Read Rules for

Safe Operation

and Instructions

Carefully

SAVE THIS

MANUAL FOR

FUTURE REFERENCE

ROUTER

DOUBLE INSULATED

Introduction

Operation
Maintenance

Repair Parts

612547-243

11.85

Designed exclusively for and sold only by

SEARS, ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684

PRINTED IN U.S.A,

FULL ONE YEAR WARRANTY ON CRAFTSMAN ROUTER
If this Craftsman Router fails to give complete satisfaction within one year from the date of purchase

RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears will
repair it free of charge.

If this Router is used for commercial or rental purposes this warranty applies for only 90 days from the

date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.

SEARS, ROEBUCK AND CO.

DEPT. 698/731A

SEARS TOWER

CHICAGO, IL 60684

iNTRODUCTION

DOUBLE INSULATION is a concept in safety, in
electric power tools, which eliminates the need for

the usual three wire grounded power cord and
grounded supply system. Wherever there is electric

current in the tool there are two complete sets of
insulation to protect the user. All exposed metal
parts are isolated from the internal metal motor

components with protecting insulation.

GENERAL
Your router is a versatile woodworking tool which

will give you years of trouble-free performance. It is

engineered with the professional in mind, but its
ease of operation allows the amateur to produce

IMPORTANTmServicing of a tool with double in-
sulation requires extreme care and knowledge of the
system and should be performed only by a qualified
service technician. For service we suggest you

return the tool to your nearest Sears Store for repair.

Always use original factory replacement parts when

servicing.

work which is beautiful and precise. All the bearings
in this tool are lubricated with a sufficient amount of

high grade lubricant for the life of the unit under nor-
real operating conditions, therefore, no further

lubrication is required.

RULES FOR SAFE OPERATION

WARNING -- DO NOT ATTEMPT TO OPERATE UNTIL YOU HAVE READ THOROUGHLY AND UNDERSTAND
COMPLETELY ALL INSTRUCTIONS, RULES, ETC. CONTAINED IN THIS MANUAL. FAILURE TO COMPLY CAN
RESULT IN ACCIDENTS INVOLVING FIRE, ELECTRIC SHOCK, OR SERIOUS PERSONAL INJURY. SAVE

OWNERS MANUAL AND REVIEW FREQUENTLY FOR CONTINUING SAFE OPERATION, AND INSTRUCTING
POSSIBLE THIRD-PARTY USER.

READ ALL INSTRUCTIONS

1. KNOW YOUR POWER TOOL -- Read owner's manual carefully. Learn its ap-
plications and limitations as well as the specific potential hazards peculiar to

this tool.

2. GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT

WITH GROUNDED SURFACES. For example: Pipes, radiators, ranges, refrig-
erator enclosures.

3. KEEP GUARDS IN PLACE and in working order.

4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

5. AVOID DANGEROUS ENVIRONMENT. Don't use power tool in damp or wet
locations or expose to rain. Keep work area well lit.

6. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work

area. Do not let visitors contact tool or extension cord.

7. STORE IDLE TOOLS. When not in use, tools should be stored in dry, high or
locked-up place = out of reach of children.

8. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it

was designed.

9. USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy
duty tool. Don't use tool for purpose not intended - for example - Don't use
a circular saw for cutting tree limbs or logs.

10. WEAR PROPER APPAREL. No loose clothing or jewelry to get caught in moving
parts. Rubber gloves and footwear are recommended when working outdoors.

Also, wear protective hair covering to contain long hair.

Page 2

RULES FOR SAFE OPERATION (Continued)

11. USE SAFETY GLASSES with all tools. Also face or dust mask if cutting
operation is dusty.

12. DON'T ABUSE CORD= Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil and sharp edges.

13. SECURE WORK. Use clamps or a vise to hold work. It's safer than using your
hand and it frees both hands to operate tool.

14. DON'T OVERREACH. Keep proper footing and balance at all times.

15. MAINTAIN TOOLS WITH CARE= Keep tools sharp at all times, and clean for best
and safest performance. Follow instructions for lubricating and changing ac-

cessories.

16. DISCONNECT TOOLS. When not in use, before servicing, or when changing at-
tachments, blades, bits, cutters, etc., all tools should be disconnected.

17. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed from tool before turning it on.

18. AVOID ACCIDENTAL STARTING. Don't carry plugged-in tools with finger on
switch. Be sure switch is off when plugging in.

19. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords suitable for use outdoors. Outdoor approved cords are marked

with the suffix W-A, for example -- SJTW-A or SJOW-A.

20. KEEP CUTTERS CLEAN AND SHARP. Sharp cutters minimize stalling and kick=

back.

21. KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from cutters. Do

not reach underneath work while cutter is rotating. Do not attempt to remove
material while cutter is rotating.

22. NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor

could ignite fumes.

23. INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired at your

nearest Sears Repair Center.

24. INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.

25. KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always

use a clean cloth when cleaning. Never use brake fluid, gasoline, or any strong
solvents to clean your tool.

26. STAY ALERT. Watch what you are doing and use common sense. Do not op-

erate tool when you are tired.

27. CHECK DAMAGED PARTS. Before further use of the tool, a guard or

other part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of mov-

ing parts, binding of moving parts, breakage of parts, mounting, and any other

conditions that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized service center unless

indicated elsewhere in this instruction manual.

28. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defect-

ive switches replaced by authorized service center.

29. Inspect for and remove all nails from lumber before routing.

30. DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influ.
ence of drugs, alcohol, or any medication.

31. SAVE THESE INSTRUCTIONS.

The operation of any Router can result in foreign objects being thrown
into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields before commencing power tool opera.
tion. We recommend Wide Vision Safety mask for use over spectacles

or standard safety glasses, available at Sears Catalog Order or Retail

Stores.

Page 3

OPERATION

WARNING: YOUR ROUTER SHOULD NEVER BE PLUGGED IN WHEN YOU ARE ASSEMBLING PARTS OR
MAKING ADJUSTMENTS. ALWAYS WEAR SAFETY GLASSES OR EYESHIELDS BEFORE BEGINNING POWER

TOOL OPERATION.

If any parts are missing do not operate your Router until the missing parts are replaced.
Before attempting to use your Router, familiarize yourself with all operating features (See Fig. 1) and safety re-

quirements. WARNING: DO NOT ALLOW FAMILIARITY WITH YOUR ROUTER TO MAKE YOU CARELESS.
REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY.

CHIP SHIELD

A clear plastic chip shield is installed on the front of the router for protection against flying dust and chips. The
chip shield is designed to fit the front opening of the router base as shown in figure 1. If necessary to remove,

squeeze the tabs on each end and pull outward. To replace, squeeze the tabs at each end, fit into the opening,
then release. DO NOT USE ROUTER WITHOUT CHIP SHIELD PROPERLY IN PLACE.

SPINDLE

LOCK

DEPTH

DEPTH
INDICATOR

RING

RING

iNDICATOR
POINT

SHIELD

FRONT VIEW

POWER

:ORD

REAR ViEW

Page 4

CLAMPING

WiNG NUT

Fig. 1