Craftsman 17227675 Owner’s Manual

Operator's Manual

3.0 Amp/5-in. Diameter

Random Orbital Sander

Model No. 172.27675

CAUTION: Read, understand and follow

all Safety Rules and Operating Instructions

in this manual before using this product.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman ®website: www.sears.com/craftsman

c(@o+

3025736

Certified

to CAN/CSA-

C22.2 No.745-1,745-2-4

Conforms to UL

STD 745-1,745-2-4

Double Insulated

• WARRANTY

• SAFETY

• UNPACKING

• DESCRIPTION

• ASSEMBLY

• OPERATION

• MAINTENANCE

Warranty ........................................................................................ Page 2

Safety Symbols ............................................................................. Page 3

Safety Instructions ......................................................................... Pages 4 - 10

Unpacking ..................................................................................... Page 10 - 11

Description ............................................................................................ Pages 11 - 12

Assembly ................................................................................................. Pages 13 - 16

Operation ................................................................................................. Pages 16- 19

Maintenance .............................................................................................. Page 20 - 21

Accessories ............................................................................................. Page 21

Parts List ................................................................................................ Page 22 - 23

Sears Repair Parts Phone Numbers ...................................................... Back Cover

ONE YEAR FULL WARRANTY ON CRAFTSMAN® PROFESSIONAL TOOL

Ifthis Craftsman Professional Tool fails due to a defect in material or workmanship

within one year from the date of purchase, RETURN ITTO ANY SEARS STORE OR PARTS AND REPAIR CENTER OR OTHER CRAFTSMAN OUTLET IN THE

UNITED STATES FOR FREE REPAIR (OR REPLACEMENT IS REPAIR PROVES IMPOSSIBLE).

This warranty does not include expendable parts such as lamps, batteries, bits, blades or sandpaper.

This warranty gives you specific legal rights, and you may have other rights, which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

SAVE THESE INSTRUCTIONS!

READ ALL INSTRUCTIONS!

/_ WARNING: Some dust created by using power tools contains chemicals

known to the State of California to cause cancer and birth defects or other reproductive harm.

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and

understanding. The symbol warnings DO NOT by themselves eliminate any danger. The instructions and warnings they give are no substitutes, for proper accident prevention

measures.

Z_ WARNING: BE SURE to read and understand all safety instructions in

this manual, including all safety alert symbols such as "DANGER", "WARNING" and "CAUTION", BEFORE using this tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or .,seriouspersonal injury.

SYMBOL MEANING

/_ SAFETY DANGER, WARNING, OR

CAUTION. May be used in conjunction with other symbols or pictographs.

ALERT

SYMBOL: Indicates

Failure to obey this safety warning WILL result in death or serious injury to yourself or to others. Always follow the

safety precautions to reduce the risk of fire, electric shock and personal injury.

Failure to obey this safety warning CAN result in death or

I/_WARNING I

serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock

and personal injury.

[/_ CAUTION I Failure to obey this safety warning MAY result in personal

injury to yourself or others or property damage. Always follow the safety precautions to reduce the risk of fire,

electric shock and personal injury.

DAMAGE PREVENTION AND INFORMATION MESSAGES

These inform user of important information and/or instructionsthat could lead to

equipment or other property damage if not followed. Each message ispreceded bythe word "NOTE:" as in the example below:

NOTE: Equipment and/or property damage may result if these instructions are not followed.

WEAR YOUR

/_WARNING: The operation ,of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool

operation, ALWAYS wear safety goggles or safety glasses with side shield and a full-face shield when needed.

We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shield,

available at Sears Stores or other Craftsman Outlets.

27675 2/11/08

/ik WARNING: BE SURE to read and understand all instructions in this manual

before using this power tool. Failure to follow all instructions may result in electric

shock, fire and / or serious personal injury.

WORK AREA SAFETY

1. Keep your work area clean and well lit. Cluttered workbenches and dark areas inviteaccidents.

2. DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust or fumes.

3. Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control.

4. Make your workshop childproof with padlocks and master switches. Lock toolsaway when not in use.

5. MAKE SURE the work area has ample lighting so you can see the work and that there are no obstructions that will interfere with safe operation BEFORE using your

power tool.

PERSONAL SAFETY

1. KNOW your power tool. Read the operator's manual carefully. Learn the tool's

applications and limitations,as well as the specific potential hazards related to this tool.

2. STAY ALERT, watch what you are doing and use common sense when operating a

powertool.

3. DO NOT use tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal

injury.

4. DRESS properly. DO NOT wear loose clothing or jewelry. Pull back long hair. Keep

your hair, clothing,and gloves away from moving parts. Loose clothing, or long hair can be caught in moving parts.Air vents often cover moving parts and should also be

avoided.

5. AVOID accidental starting. Be sure switch is in "OFF" position before plugging in. DO NOT carry toolswith your finger on the switch. Carrying tools with your finger on the

switch or plugging in tools that have the switch inthe "ON" position invites accidents.

6. REMOVE adjusting keys or blade wrenches before turning a tool"ON". A wrench that is leftattached toa rotatingpart of a tool may result in personal injury.

7. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

8. ALWAYS SECURE YOUR WORK. Use clamps or a vise to hold work when practical. It is safer than using your hand and frees both hands tooperate tool.

9. USE SAFETY EQUIPMENT. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protectionmust be used for appropriate conditions.

TOOL USE AND CARE SAFETY

/_ WARNING: BE SURE to read and understand all instructions before I

operating this power tool. Failure to follow all instructions listed below may

result in electric shock, fire and/or serious personal injury.

1. ALWAYS use clamps or other practical ways to secure and support the

workpiece to a stable platform. Holding the work by hand or against your body

isunstable and may lead to loss of control.

2. DO NOT force the tool. Use the correct tool for your application. The correct tool

willdo the job better and safer at the rate for which it is designed.

3. DO NOT use the tool if switch does not turn it "On" or "Off". Any toolthat

cannot be controlled withthe switch is dangerous and must be repaired.

4. DISCONNECT the plug from the power source before making any

adjustments, changing accessories or storing the tool. Such preventive safety measures reduce the risk of startingthe tool accidentally.

5. STORE idle tools out of the reach of children and other untrained persons. Tools are dangerous inthe hands of untrained users.

6. MAINTAIN tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bindand are easier to control.

7. Keep sandpaper clean, remove excess build-up of dust and debris. Replace sandpaper when worn, this will provide better sanding results.

8. CHECK for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool'soperation. If damaged, have the toolserviced before using. Many accidents are caused by poorly maintained tools.

9. USE ONLY accessories that are recommended for tills tool. Accessories that may be suitable for one tool may become hazardous wlhenused on another tool.

/_ WARNING: Empty dust bag before storage to Ilelp prevent possible fire I

hazard, especially when resin coating or linseed oil finishes have been sanded.

ELECTRICAL SAFETY

/_ WARNING: Do not permit fingers to touch

the terminals of plug when installing or removing the plug from the outlet.

1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other).This plug will fit in a polarized outlet only one way. Ifthe plug

does not fit fully in the outlet, reverse the plug. If itstill does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.

Cover of Grounded

Outlet Box ------

27675 2/11/08

ELECTRICAL SAFETY

/_ WARNING: Do not permit fingers to touch the terminals of plug when J

installing or removing the plug from the outlet.

2. Double insulation [] eliminates the need for the three-wire grounded power cord and grounded power supply system. Applicable onlyto Class II (double-insulated) tools.

This tool is a double insulated tool.

I /_ WARNING: Double insulation DOES NOT take the place of normal safety I

precautions when operating this tool.

3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied iswithin the voltage marked on the tool'sdata plate. DO NOT use "AO only" rated tools with

a DC power supply.

4. AVOID body contact with grounded surfaces, such as pipes, radiators, ranges and refrigerators. There isan increased riskof electric shock if your body isgrounded.

5. DO NOT expose power tools to rain or wet conditions or use power tools in wet or damp locations. Water entering a power toolwill increase the risk of electric shock.

6. INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears Service Center. BE SURE to stay constantly aware of the cord locationand keep it well

away from moving parts.

7. DO NOT abuse the cord. NEVER use the cord to carry the tool by or to pull the

plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the riskof electricshock.

EXTENSION CORDS Use a proper extension cord. ONLY use cords listed by Underwriters Laboratories (UL).

Other extension cords can cause a drop in line voltage, resulting in a loss of power and overheating of tool. For thistool an AWG (American Wire Gauge) size of a least 14-gauge is recommended for an extension cord of 25-ft. or less in length. Use 12-gauge for an

extension cord of 50-ft. Extension cords 100-ft. or longer are not recommended. Remember, a smaller wire gauge size has greater capacity than a larger number (14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire has more capacity

than 14-gauge). When in doubt use the smaller number. Wl_enoperating a power tool outdoors, use an outdoor extension cord marked "W-A" or "W". These cords are rated for outdoor use and reduce the riskof electric shock.

/_, CAUTION: Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber, tools or other

obstructions while you are working with a power tool.

/_ WARNING: Check extension cords before each use. If damaged replace

immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock, resulting in serious injury.

SAFETY SYMBOLS FOR YOUR TOOL The label on your tool may include the following symbols.

V....................................................................... Volts

A...................................................................... Amps

Hz.................................................................... Hertz

W..................................................................... Watts

rain.................................................................. Minutes

_., .................................................................... Alternating current

.................................................................. Direct current

no .................................................................... No-load speed

[] .................................................................... Class II construction,Double Insulated

RPM .......................................................... Revolutionsper minute

SPM............................................................ Strokes per minute

OPM.......................................................... Orbits per minute

Z_ .................................................................... Indicates danger, warning or caution.

It means attention! Your safety is involved.

SERVICE SAFETY

1. If any part of this tool is missing or should break, bend, or fail in any way;

or should any electrical component fail to perform properly: SHUT OFF the

power switch and remove the tool's plug from the power source and have the missing, damaged or failed parts replaced BEFORE resuming operation.

2. Tool service must be performed only at a Sears Service Center. Service or

maintenance performed byunqualified personnel could result in a risk of injury,

3. When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized

parts orfailure to follow maintenance instructionsmay create a riskof electric shock or injury.

SAFETY RULES FOR POWER SANDERS

1. HOLD TOOL by insulated gripping surfaces when sanding where tool may contact

hidden wiring, such as walls, floors, or its own power (-ord. Contact with a "live" wire will

make exposed metals parts of the tool"live" and shock the operator.

2. INSPECT FOR AND REMOVE all nails, screws, staples or any embedded pieces of metal from surface to be sanded. These protrusions coulcldamage the sandpaper, the cushion of the sander and cause lossof control. Followingthis rule will reduce the

risk of serious personal injury and damage to the sander.

3. NEVER use this or any power sander for wet sanding or liquid polishing. Failure to follow this rule will increase the riskof electric shock.

4. ALWAYS clamp the workpiece securely so it will not move under the sander. Unsecured work could be thrown towards the operator, causing injury.

5. DO NOT force the sander. The weight of the sander supplies adequate pressure. Let the sander and the griton the sandpaper do the work.

6. DO NOT sand in any one place for too long. The sander's rapid action may remove toomuch material and make the surface uneven.

z_ WARNING: Some dust created by using power tools contains chemicals

known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks and cement and other masonry products.

• Arsenic and chromium, from chemically treated lumber.

Your risk from these exposures varies, depending upon how often you do

this type of work. To reduce your exposure to these chemicals:

• Work in a well-ventilated area.

• Work with approved safety equipment, such as those dust masks that

are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and other construction activities. Wear protective clothing and wash

exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

/_ WARNING: Use of this tool can generate and/or disburse dust, which may

cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure.

Direct particles away from face and body.

/_ WARNING: Collected sanding dust from sanding :surface coatings

(polyurethane, linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty dust bag frequently and strictly follow

sander manual and coating manufacturer's instructions.

/_ CAUTION: When working on metal surfaces, DO NOT use the dust bag

or a vacuum cleaner because sparks are generated. Wear safety glasses and a

dust mask. Due to the danger of fire, do not use your sander to sand magnesium

surfaces. Do not use for wet sanding.

SANDING PAINTS

SANDING LEAD BASED PAINT is NOT RECOMMENDED ('Juetothe difficulty of controllingthe contaminated dust. The greatest danger of lead poisoning is to children

and pregnant women.

Since it isdifficult to identify whether or not a paint contains lead without a chemical

analysis, we recommend the following precautions when sanding any paint:

• NO children or pregnant women should enter the work area where the paint sanding is being done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work

area. The filter should be replaced daily, or whenever (if) the wearer has difficulty breathing.

NOTE:Onlythosedustmaskssuitableforworkingwithleadpaintdustandfumesshould

beused.Ordinarypaintingmasksdonotofferthisprotection.Seeyourlocalhardware dealerfortheproper(NIOSHapproved)mask.

NO EATING, DRINKING OR SMOKING should be done in the work area to

prevent ingesting contaminated paint particles. 'Workers should wash and clean up BEFORE eating, drinking or smoking. Artiicles of food, drink, or

smoking should NOT be left inthe work area where contaminated dust would settle on them.

° Paint should be removed in such a manner as to m,inimize the amount of dust

generated.

• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness.

Sanding should be done in a manner to reduce trac'king of paint dust outside

the work area.

All surfaces in the work area should be vacuumed and thoroughly cleaned daily

for the duration of the sanding project. Vacuum filter bags should be changed frequently.

Plastic drop cloths should be gathered up and diisposed of along with any dust

chips or other removal debris. They should be placed in sealed refuse receptacles

and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be KEPT AWAY from the immediate work area.

All toys, washable furniture and utensils used by children should be washed

thoroughly before being used again.

ADDITIONAL RULES FOR SAFE OPERATION

Z_ WARNING: BE SURE to read and understand all instructions.

Failure to follow all instructions listed below may result in electric shock, fire

and/or serious personal injury.

1. Know your power tool. Read operator's manual carefully. Learn the applications and limitations,as well as the specific potential hazardsrelatedto this tool. Followingthis rule will reduce the riskof electric shock, fire or serious injury.

2. ALWAYS wear safety glasses or eye shields when using this tool. Everyday eyeglasses have onlyimpact-resistantlenses;they are NOT safety glasses.

3. PROTECT your lungs. Wear a face mask or dust mask iifthe operationis dusty.

4. PROTECT your hearing. Wear appropriate personal Ihearingprotectionduring use. Under some conditionsnoise from this product may contn'ibuteto hearing loss.

5. ALL VISTORS AND BYSTANDERS MUST wear the same safety equipment that the

operatorofthe toolwears.

27675 2/11/08

ADDITIONAL RULES FOR SAFE OPERATION cont.

6. INSPECT the tool cords periodically and if damaged have them repaired at your nearest Sears Service Center. ALWAYS BE AWARE of the cord location.

7. ALWAYS check the tool for damaged parts. Before further use of the tool, a guard

or other part that is damaged should be carefully checked to determine if itwill operate properlyand perform itsintended function. Check for misalignment or binding of moving

parts, breakage of parts,and any other condition that may affect the tool's operation.

A guard or other part that is damaged should be properly repaired or replaced at a Sears Service center.

8. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If someone borrows this tool, make sure they have these instructions also.

/_ WARNING: This power tool should NEVER be €-onnected to the power

source when you are assembling parts, making adjustments, installing or

removing sandpaper, cleaning or when it is not in use. Disconnecting the sander

will prevent accidental starting, which could cause serious personal injury.

1. Remove the sander from the carton and inspect itcarefully to make sure

that no breakage or damage has occurred during shipping.

2. Do not discard any of the packing materials until all parts are accounted for.

3. Included with your sander is a dust bag assembly, with vac adapter.

4.2 discs of hook and loop sandpaper are included; orle fine grit, and one medium grit.

5. If any of the parts are damaged or missing (refer to PAFr]-s LIST below), return the sander to your nearest Sears store or Craftsman outlet to have the sander replaced.

the missing parts are replaced. Failure to do so could result in possible serious

I /IX WARNING: If any parts are missing, DO NOT operate this power tool until I

personal injury.

]

1. Sander

PARTS LIST (Fig. 1)

Q _ 2. Dust Bag

Assembly

3. Vac Adapter with dual

dust ports

4. Two 5-in. Hook and Loop Sanding Dis('s with Pre-Punched Holes

5. Operator's Manual

KNOW YOUR RANDOM ORBIT SANDER (Fig. 2)

NOTE: Before attempting to use your sander, familiarize yourself with all of the

operating features and safety requirements.

Your Professional 5" Random Orbit Sander has a precision-built electric motor and it should be connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current). DO NOT operate on direct current (DC). The large voltage drop will cause a loss of power and the motor will overheat. If the sander does not operate when plugged into correct

120-volt, 60-Hz AC ONLY outlet, check the power supply. This sander has a 10-ft, 2-wire power cord (no adapter needed).

This Random Orbit Sander has the following features:

1. Powerful 3.0 amp motor provides the torque, power and durability for a variety of continuous sanding applications.

2. Variable speed 5,000 to 12,000 OPM orbits per minute (no-load speed) is controlled by variable speed dial. Match with the correct speed and sandpaper grit to the surface

being sanded for either fast material removal or a fine, :smoothfinish.

3. Random orbital action with 1/16-in. orbit diameter helps to provide a swirl free finish.

4. Ergonomically designed Palm Grip Handle with Molded-in Comfort Grip

for maximum balance, control, gripping comfort and redu(-ed operator fatigue.

5. Precision-tuned counterbalanced system reduces vibration for smooth operation

and less operator fatigue.

27675 2/11/08

This Random Orbit Sander has the following features cont.:

6. On/Off rocker switch is conveniently located for easy control. Sealed to keep out

dust for long life.

7. Hook and Loop Backing Pad for easy attachment of 17rookand looptype sanding discs

with pre-punched holes.

8. High impact-resistant housing helps protect tool fron7damage and reduces weight.

9. Built-in Dust Collection System Dust bag assembly with dual dust ports collects dust from work surface through holes in backing pad and sanding disc. Use either the dust bag, or attach a 11/4or 21/2-inchvac hose and wet / dry vac (sold separately) for

dust collection. Helps keep work surfacearea clean and extends life of sanding disc.

10. Permanently lubricated 100% ball bearings for smooth operation and long life.

Comfort Grip Handle

Speed Dial

Fig 2

On/Off Rocker Switch

Dust Bag

Vac Adapter with Dual Dust Ports

Hook: and Loop Backing Pad

Assembly

No-load Speed 5000-12000 OPM (orbits per minute) variable speed Rating 120 Volts, 60 Hz AC

Input 3.0 Amps

Orbit Diameter 1/16-in. Sanding Disc Size 5-in. Diameter

Paper Type Hook and Loop Discs with Pre-Punched Holes

Z_ WARNING: Your sander should NEVER be ('onnected to the power source

when you are assembling parts, making adjustments, installing or removing sandpaper, cleaning or when it is not in use. Disconnecting the sander will prevent accidental starting, that could cause serious personal injury.

INSTALLING THE SANDPAPER (See Figs. 3) ALWAYS inspect the sandpaper before installing.DO NOT use if broken or defective.

1. Unplug the sander.

Z_ WARNING: Failure to unplug the sander could result in accidental

starting causing possible serious personal injury.

NOTE: Remove dust bag assembly when installing sandpaper. ALWAYS remember I

to reattach the dust bag assembly before beginning sanding operation

(see page 15, Fig. 6).

2. Align the holes in the sanding disc with the holes inthe hook and loop backing pad. NOTE: Holes in sanding disc must line up with holes in the backing pad in order for

the dust collection feature of the sander to function properly.

3. Press the sanding disc against the backing pad as firmly as possible.

I OTE: For best adhesion, we recommend that you clean the backing pad and the

sanding disc backing occasionally by brushing them lightly with a small brush.

Fig 3

Backing Pad

Hook and Loop Sanding

Disc with Pre-Punched Holes

27675 2/11/08

TO REMOVE AND EMPTY DUST BAG (See Fig. 4 and 4a)

1, Unplug the sander.

A WARNING: Failure to unplug the sander could result in accidental starting J

causing possible serious personal injury.

2. Locate (2) tab connectors on either side of vac adapter/dust bag assembly and squeeze. Pull assembly straight back and off of dust exhaust I_ole (',seeFig. 4).

3. Turn dust bag assembly counterclockwise (embossed arrows show unlock and lock rotation) and remove bag from vac adapter (see Fig. 4a, 4b).

Dust Exhaust Hole

Fig. 4a

Counterclockwise

OFF

DustBag

Assembly

for ON

Empty bag by shaking aggressively until completely empty. Wipe dust and debris from

the vac adapter.

Reattach the bag assembly onto the vac adapter, and reattach vac adapter and

dust bag assembly onto the sander.

NOTE: Empty dust bag frequently when sanding so dust collection system

works properly.

VacAdapter DustBag withDualDust Assembly

Ports

DustBag

Assembly

Vac Adapter with Dual Dust Ports

Fig. 4b

I _, WARNING: Empty dust bag before storage 1toIhelpprevent possible fire I

hazard, especially when resin coating or linseed oil finishes have been sanded.

NOTE: For more efficient operation, we recommend that you empty the dust bag when it is no more than half full. This will allow tlhe air to flow through the bag better. ALWAYS empty and clean the dust bag thoroughly when you've

finished sanding and before you store the sander.

A'I-rACHING VAC HOSE TO THE DUST COLLECTION SYSTEM (See Fig. 5)

When sanding for extended periods of time, you can easily attach your sander to a vac hose and wet/dry vac (sold separately).

1. Unplug the sander.

I Z_ WARNING: Failure to unplug the sander could result in accidental starting Icausing possible serious personal injury.

2. Remove dust bag assembly from the vac adapter (see page 14, Fig. 4a and 4b).

3. Connect vac adapter with dual dust ports to dust exhaust hole of sander (see Fig. 5).

4. Attach either a 11/4or 21/2-in vac hose onto the vac adapter's dual dust ports

( see Fig. 5a and 5b).

Fig. 5a

5. Connect hose to wet / dry 'vac.Turn

vac on while operating sander.

hose adapter'

to exhaust hole of sander

Fig. 5

Connect

11/4-in. hose

Connect 2'/2-in. hose

Fig. 5b

27675 2/11/08

ATTACHING VAC HOSE TO THE DUST COLLECTION SYSTEM cont.

NOTE: A standard 1l/d-in, vac hose connection fits; inside the smaller diameter hole inside the dust exhaust, while a standard 21/2-in. vac hose connection

fits inside the larger hole of the dust exhaust.

/ik WARNING: When sander is not connected to vacuum, always install

dust bag back on sander. Failure to do so could cause sanding dust or foreign objects to be thrown into the face or eyes which could result in possible

serious injury.

/{k WARNING: Collected sanding dust from sanding surface coatings

(polyurethane, linseed oil, etc.) can self-ignite in sandier dust bag or elsewhere and cause fire. To reduce risk, empty dust bag frequeritly and strictly follow

sander manual and coating manufacturer's instructions.

/{k WARNING: When working on metal surfaces, r)o NOT use the dust bag

or a vacuum cleaner because sparks are generated. Wear safety glasses and a dust mask. Due to the danger of fire, do not use your sander to sand magnesium

surfaces. Do not use for wet sanding.

Before attempting to use any tool, be sure to familiarize yourself with all the

operating features and safety instructions.

/_ WARNING- IF ANY PARTS ARE MISSING, DO NOT OPERATE YOUR

SANDER UNTIL THE MISSING PARTS ARE REPLACED. FAILURE TO FOLLOW THIS RULE COULD RESULT IN SERIOUS PERSONAL INJURY.

i i_k WARNING: DO NOT let familiarity with your sander make you careless. I

Remember that a careless fraction of a second is sufficient to cause severe injury.

ON/OFF ROCKER SWITCH (see Fig. 6)

This switch is sealed to help keep out dust for a longer life and is conveniently located

near the front of the palm grip handle.

Start the sander by pushing in the part of the switch with theE], Let the motor build to its

maximum speed before starting sanding

operation. To turn sander off, push side of switch with the [].

+ 35 hidden pages