Craftsman 152221040 Owner’s Manual

Owner's Manual

CRRFr MRH

1.5 Horsepower (continuous duty) 2 Horsepower (maximum developed) 3450 R.P.M. (no load R.P.M.)

10-in. LE SAW

Model No.

152.221040

Customer Helpline

1-800-897-7709

CAUTION:

FOR YOUR OWN SAFETY; Read and follow all of the Safety and Operating Instructions before Operating this Table Saw.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Part No. OR91550 Revision: D EspaRolpg. 45

Please have your Model No.

and Serial No. available.

SECTION PAGE

Warranty .......................................................................................................................................................................... 2

Product Specifications .................................................................................................................................................. 2

Glossary of Terms .......................................................................................................................................................... 3

Safety instructions ......................................................................................................................................................... 4

Guidelines for Extension Cords ................................................................................................................................... 5

Grounding instructions ................................................................................................................................................. 6

Specific Safety instructions for Table Saw .................................................................................................................. 7

Accessories and Attachments ...................................................................................................................................... 9

Carton Contents ........................................................................................................................................................... 11

Know Your Table Saw .................................................................................................................................................. 14

Assembly instructions ................................................................................................................................................. 15

Operations and Adjustments ...................................................................................................................................... 23

Maintenance .................................................................................................................................................................. 37

Troubleshooting Guide ................................................................................................................................................ 38

Part List ......................................................................................................................................................................... 39

Espanol ......................................................................................................................................................................... 45

Service information ...................................................................................................................................................... 84

FULL ONE YEAR WARRANTY If this product fails due to a defect in material or workmanship within one year from the date of purchase, return it

to the nearest Sears Service Center for repair, free of charge. If this product is used for commercial or rental purposes, this warrant y applies only for 90 days from date of purchase.

This warranty gives you specific legal dghts, and you may also have other dghts, which vary, from state to state. Sears, Roebuck and Co., Dept 817 WA, Hoffman Estates, IL 60179

Table in front of blade at max

Motor type Induction Continuous duty HP 1.5 Maximum developed HP 2

Amps 15/7.5

Volts 120/240 Hertz 60

RPM 3450 R.P.M. (no load R.P.M.) Blade tilt Left tilt

Blade drive Poly-V Belt Blade diameter 10-in.

Blade arbor 5/8-in. Number of teeth 40

Blade speed 3450 R.P.M. Fence type Front locking, Extruded

aluminum Fence and Rails

Max depth-of-cut at 90-degree 3-3/8-in. Max depth-of-cut at 45-degree 2-1/4-in.

Max rip to the right of the blade 25-in. Max rip to the left of the blade 12-in.

depth-of-cut

Max dado width Max. dado blade diameter

Left and right table wing Weight of table saw

To avoid electrical shock to yourself and damage to the Table Saw, use proper circuit protection. Do not expose to

rain, or use in a damp environment.

The Table Saw is factory wired for 120V, 60 Hz, operation. Connect to a 120V, 15 amp branch circuit and use a 15

amp time delay fuse or circuit breaker. The electrical circuit cannot have any wire size less than #14. To avoid shock or fire, replace power cord immediately if it is damaged in any way.

12-1/2-in. 13/16-in.

8-in. 8-in, Stamped Steel

350 Ibs.

Anti-KickbackFingers- Asafetydeviceattachedtothe bladeguardandsplitterassemblydesignedtostopa workpiecefrombeingthrownbackduringacuttingopera-

tion.

Arbor- Theshaftonwhichthebladeoraccessorycut- ting-toolismounted.

BevelCut- Theoperationofmakinganycutwiththe bladesetonadegreeotherthan90degrees.

CompoundCut- Theoperationofmakingbotha bevel andamitercutatonetime.

Crosscut- Theoperationofmakingacutacrossthe grainorwidthofaworkpiece.

Dado- Anon-throughcutthatproducesasquarenotch.

Adadoistypicallyfrom1/8-in.to13/16-in.wide.Adado

requiresaspecialsetofblades,notincludedwiththis tablesaw.

Kerf- Thematerialremovedbythebladeinthework- pieceduringanycuttingoperation.

Kickback- Whentheworkpieceisthrownbacktowards theoperatorduringacuttingoperationwhentheworkpiece

initiallycontactsthebladeoriftheworkpiecepinchesthe blade.Kickbackisdangerousandcanresultinserious

injury.

MiterCut- Theoperationofmakingacutusingthemiter gaugeatanyangleotherthanzerodegrees.

PushStick- Anaccessorydevicethatcanbemadeor purchasedtohelppushtheworkpiecethroughtheblade.

Apushstickisusedtokeeptheoperator'shandsaway fromthebladewhenrippinganarrowworkpiece.

Rabbet- Asquarenotchintheedgeoftheworkpiece.

Resaw- Theoperationofmakingacuttoreducethe thicknessoftheworkpiece.

Featherboard- Anaccessorydevicethatcanbemadeor purchasedtohelpguideorholddownaworkpieceduring cuttingoperations.

Freehand- Averydangerousoperationofmakingacut withoutusingthefenceormitergaugeinacuttingopera-

tion.FreehandcutsmustneverbeperformedonaTable Saw.

Gum,PitchorResin- Asticky,sapbasedresiduethat comesfromwoodproducts.

Heel- Themisalignmentofthebladetothemiterslots; whenthebladeisnotparalleltothemiterslots.

RipCut- Theoperationofmakingacutwiththegrainof theworkpiece.

SawBladePath- Theareathatisdirectlyinlinewiththe blade,includingareaover,under,behindandinfrontofit.

SetoftheSawBlade- Thedistancethatthetipsofthe sawbladeareangledoutwardsfromthethicknessofthe

blade.Thesetofthesawbladeteethallowsfortheblade bodytopasssafelythroughallcuts.

Table/WorkArea- Thetotalsurfaceofthetopofthetable sawonwhichtheworkpiecerestswhileset-uporcutting

operationsarebeingperformed.

GENERAL SAFETY INSTRUCTIONS

Operating a Table Saw can be dangerous if safety and common sense are ignored. The operator must be familiar with the operation of the tool. Read this manual to understand this Table Saw. DO NOT operate this Table Saw ifyou do not fully understand the limitations of this tool. DO NOT modify this Table Saw in any way. REMEMBER: Your personal safety is your responsibility.

BEFORE USING THE TABLE SAW

To avoid serious injury and damage to the tool, read and follow all of the Safety and Operating Instructions before operating the Table Saw.

1. READ the entire Owner's Manual. LEARN how to use the tool for its intended applications.

GROUND ALL TOOLS. If the tool is supplied with a 3-prong plug, it must be plugged into a 3-contact electrical receptacle. The 3rd prong is used to ground the tool and provide protection against

accidental electric shock. DO NOT remove the 3rd prong. See Grounding Instructions.

3. AVOID A DANGEROUS WORKING ENVIRON= MENT. DO NOT Use electrical tools in a damp

environment or expose them to rain.

4. DO NOT use electrical tools in the presence of flammable liquids or gasses.

ALWAYS WEAR EYE PROTECTION. Any power tool can throw debris into the eyes during opera- tions, which could cause severe and permanent eye damage. Everyday eyeglasses are NOT safety glasses. ALWAYS wear Safety Goggles (that comply with ANSi standard Z87.t) when operating power tools. Safety Goggles are available at Sears Retail Stores. Hearing equipment should comply

with ANSi S3.t 9 Standards.

10.

ALWAYS UNPLUG THE TOOL FROM THE ELEC= TRICAL RECEPTACLE when making adjustments,

changing parts or performing any maintenance.

11.

KEEP PROTECTIVE GUARDS iN PLACE AND iN WORKING ORDER.

12.

AVOID ACCIDENTAL STARTING. Make sure that the power switch isin the "OFF" position before plug-

ging in the power cord to the electrical receptacle.

13.

REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning the tool "ON".

14.

USE ONLY RECOMMENDED ACCESSORIES. Use of incorrect or improper accessories could cause serious injury to the operator and cause

damage to the tool. If in doubt, check the instruction manual that comes with that particular accessory.

ALWAYS keep the work area clean, well lit, and organized. DO NOT work in an environment with floor surfaces that are slippery from debris, grease,

and wax.

6. KEEP ViSiTORS AND CHILDREN AWAY from the

table saw. DO NOT permit people to be in the immediate work area, especially when the electrical tool is operating.

DO NOT FORCE THE TOOL to perform an opera- tion for which it was not designed. It will do a safer and higher quality job by only performing operations

for which the tool was intended.

8. WEAR PROPER CLOTHING. DO NOT wear loose

clothing, gloves, neckties, or jewelry. These items can get caught in the machine during operations and pull the operator into the moving parts. Users must wear a protective cover on their hair, if the hair is long, to prevent it from contacting any mov- ing parts.

15.

NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to the "OFF" position. DO NOT leave the tool until it has come to a complete

stop.

16.

DO NOT STAND ON A TOOL. Serious injury could result if the tool tips over or you accidentally contact

the tool.

17.

DO NOT store anything above or near the tool where anyone might try to stand on the tool to

reach it.

18.

MAiNTAiN YOUR BALANCE. DO NOT extend yourself over the tool. Wear oil resistant rubber-

soled shoes. Keep floor clear of debris, grease, and wax.

19.

MAiNTAiN TOOLS WITH CARE. Always keep tools clean and in good working order. Keep all blades

and tool bits sharp.

20.EACHAND EVERY TIME, CHECK FOR DAM=

AGED PARTS PRIOR TO USING THE TOOL. Carefully check all guards to see that they operate

properly, are not damaged, and perform their intended functions. Check for alignment, binding or breaking of moving parts. A guard or other part that is damaged should be immediately repaired or replaced.

21. CHILDPROOF THE WORKSHOP AREA by remov- ing switch keys, unplugging tools from the electrical

receptacles, and using padlocks.

GUIDELINES FOR

EXTENSION CORDS

The smaller the gauge-number, the larger diameter of the extension cord. If in doubt of the proper size of an

extension cord, use a shorter and thicker cord. An undersized cord will cause a drop in line voltage result-

ing in a loss of power and overheating. USE ONLY A

3-WIRE EXTENSION CORD THAT HAS A 3-PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL'S PLUG.

22. DO NOT OPERATE TOOL iF UNDER THE iNFLUENCE OF DRUGS OR ALCOHOL.

23. SECURE ALL WORK. When it is possible, use clamps or jigs to secure the workpiece. This is safer

than attempting to hold the workpiece with your hands.

24. STAY ALERT, WATCH WHAT YOU ARE DOING, AND USE COMMON SENSE WHEN OPERATING

A POWER TOOL. DO NOT USE A TOOL WHILE TIRED OR UNDER THE iNFLUENCE OF DRUGS,

ALCOHOL, OR MEDICATION. A moment of inattention while operating power tools may result

in serious personal injury.

25. Use of this tool can generate and disburse dust or other airborne particles, including wood dust,

crystalline silica dust and asbestos dust. Direct particles away from face and body. Always operate

tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever

possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid pro- longed contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

26. USE A PROPER EXTENSION CORD iN GOOD CONDiTiON. When using an extension cord, be

sure to use one heavy enough to carry the current your product will draw. Please see "MiNiMUM

RECOMMENDED GAUGE FOR EXTENSION CORDS (AWG)" table for correct sizing of an

extension cord. If in doubt, use the next heavier gauge.

If you are using an extension cord outdoors, be sure it is marked with the suffix "W-A" ("W" in Canada) to indi-

cate that it is acceptable for outdoor use.

Be sure your extension cord is properly sized, and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person

before using it.

Protect your extension cords from sharp objects, exces- sive heat, and damp or wet areas.

120 VOLT OPERATION ONLY

25'LONG 50' LONG 100' LONG

0 to 6 Amps

6 to 10 Amps 10 to 12 Amps 12 to 15 Amps

0 to 6 Amps

6 to 10 Amps 10 to 12 Amps 12 to 15 Amps

18 AWG 18 AWG 16 AWG 14 AWG

240 VOLT OPERATION ONLY

25' LONG

18 AWG 18 AWG 16 AWG 14 AWG

16 AWG 16 AWG 16 AWG 12 AWG

50' LONG

18 AWG 18 AWG 16 AWG

12 WG

16 AWG 14 AWG 14 AWG

Not

recommended

100' LONG

16 AWG 14 AWG 14 AWG

Not

recommended

27. DiRECTiON OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade

or cutter only.

THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC

SHOCK.

USE ONLY A 3=WIRE EXTENSION CORD THAT HAS

A 3=PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL'S PLUG.

IN THE EVENT OF A MALFUNCTION OR BREAK- DOWN, grounding provides the path of least resistance

for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that

has an equipment-grounding conductor and a ground- ing plug. The plug MUST be plugged into a matching

electrical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.

DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the electrical receptacle, have the proper electrical receptacle installed by a qualified electrician.

IMPROPER ELECTRICAL CONNECTION of the equip- ment-grounding conductor can result in risk of electric

shock. The conductor with the green insulation (with or without yellow stripes) is the equipment-grounding

conductor. DO NOT connect the equipment-grounding conductor to a live terminal if repair or replacement of

the electric cord or plug is necessary.

CHECK with a qualified electrician or service personnel if you do not completely understand the grounding

instructions, or if you are not sure the tool is properly grounded.

The motor supplied with your Table Saw is a dual voltage 120/240 volts, 60 hertz alternating current, single phase

motor. It is shipped wired for 120 volts application. Never connect the green or ground wire to a live terminal.

REPLACE A DAMAGED OR WORN CORD IMMEDI=

ATELY. FOR GROUNDED, CORD=CONNECTED MACHINES

iNTENDED FOR USE ON A SUPPLY CiRCUiT HAVING A NOMINAL RATING LESS THAN 150 VOLTS.

This tool is intended for use on a circuit that has an electrical receptacle as shown in FIGURE "IA'.

FIGURE "IA" shows a 3-wire electrical plug and elec- trical receptacle that has a grounding conductor. If a

properly grounded electrical receptacle is not available, an adapter as shown in FIGURE "IB" can be used to

temporarily connect this plug to a 2-contact ungrounded receptacle. The adapter has a rigid lug extending from it

that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box. THIS

ADAPTER IS PROHiBiTED iN CANADA.

CAUTION: In all cases, make certain the electrical receptacle in question is properly grounded. If you are

not sure have a certified electrician check the electrical receptacle.

The motor supplied with your Table Saw is a dual volt- age, 120/240 volt, single phase motor. If it is desired to operate your table saw at 240 volts, it is necessary to reconnect the motor leads in the motor junction box by following the wiring diagram on the junction box cover.

MAKE CERTAIN the motor is disconnected from power source before reconnecting motor leads.

Fig. 1A

120 VOLT

grounding conductor

3-wire electrical cord

electrical receptacle

Fig. 1B

120 VOLT

grounding conductor

3-wire electrical cord

grounding adapter lug

2-prong

electrical

receptacle

It is also necessary to replace the 120 volt plug, sup- plied with the motor, with a UL/CSA Listed plug suitable

for 240 volts and rated current of the saw. Contact a local qualified electrician for proper procedures to install

the plug. The table saw must comply with all local and national electrical codes after the 240 volt plug is installed.

The table saw with a 240 volt plug should only be con- nected to an outlet having the same configuration as

the plug shown in Figure "1C". No adapter is available or should be used with the 240 volt plug.

MAKE CERTAIN that masks or respirators are MSHA/NIOSH approved.

The operation of any Table Saw can result in debris being thrown into your eyes, which can result in severe eye damage. ALWAYS wear Safety Goggles (that com- ply with ANSi standard Z87.1) when operating the Table Saw. Safety Goggles are available at Sears Retail Stores. Keep your thumbs and fingers away from the

blade while it is spinning.

Fig. 1C

current

grounded outlet box

240 VOLT carrying

prongs

grounding blade is

longest of the 3 blades

MAKE CERTAIN the receptacle in question is properly grounded. If you are not sure have a qualified electri- cian check the receptacle.

This Table Saw is for indoor use only. Do not expose to rain or use in damp locations.

Basic precautions should always be followed when using your Table Saw. To reduce the risk of injury, electrical shock or fire, comply with the safety rules

listed below:

1. READ and understand the instruction manual before operating the Table Saw.

2. DO NOT OPERATE THiS MACHINE until it is assem- bled and installed according to the instructions.

3. OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not

familiar with the operation of this machine.

4. DO NOT leave the Table Saw plugged into the elec- trical outlet. Unplug Table Saw from the outlet when

not in use and before servicing, changing blades and cleaning.

5. ALWAYS turn the power switch "OFF" before unplugging the Table Saw.

6. TO REDUCE THE RISK OF ELECTRICAL SHOCK, do not use outdoors. Do not expose to

rain. Store indoors.

SPECIFIC SAFETY INSTRUCTIONS

FOR TABLE SAWS

CALIFORNIA PROPOSITION 65

SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING AND OTHER CON=

STRUCTION ACTiViTiES contains chemicals known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such

as those dust masks that are specially designed to filter out microscopic particles.

7. FOLLOW all electrical and safety codes, including the National Electric Code (NEC) and the

Occupational Safety and Health Regulations (OSHA). All electrical connections and wiring should

be made by qualified personnel only.

8. DO NOT handle the plug or Table Saw with wet hands.

9. USE only as described in this manual. USE acces- sories only recommended by Sears.

10. DO NOT pull the Table Saw by the power cord. NEVER allow the power cord to come in contact with sharp edges, hot surfaces, oil or grease.

11. DO NOT unplug the Table Saw by pulling on the power cord. ALWAYS grasp the plug, not the cord.

12. REPLACE a damaged cord immediately. DO NOT use a damaged cord or plug. If the Table Saw is not operating properly, or has been damaged, left out-

doors or has been in contact with water, return it to a Sears Service Center.

13. DO NOT use the Table Saw as a toy. DO NOT use near or around children.

14.TheTableSawisdesignedforhomeuseorlight 27.NEVERperformlayout,assemblyorset-upworkon commercialdutyONLY. thetable/workareawhenthemachineis running.

28.

15.CONNECTTableSawtoaproperlygroundedoutlet only.Seegroundinginstructions.

NEVER reset the thermal-overload button before you have turned the table saw "OFF".

16.ALWAYSUSEtheguardswheneverpossible. Checktoseethattheyareinplace,securedand

workingcorrectly.

17.AVOIDKICKBACKby:

• Keepingbladesharpandfreeofrustandpitch.

• Keepingripfenceparalleltosawblade.

• Usingsawbladeguardandsplitterassemblyfor

everypossibleoperation,includingallthrough- sawing.

• Pushingtheworkpiecepastthesawbladepriorto

release.

• Neverripaworkpiecethatis twistedorwarped,

ordoesnothavea straightedgetoguidealong thefence.

• Usingfeatherboardswhenthebladeguardand

splitterassemblycannotbeused. Neversawingalargeworkpiecethatcannotbe

controlled. Neverusingthefenceasaguidewhencross-

cutting.

• Neversawingaworkpiecewithlooseknotsor

otherflaws.

18.REMOVEcut-offpiecesanddebrisfromthetable beforestartingthesaw.Thevibrationofthesaw

maycausethemtomoveintothesawbladeandbe thrownout.Aftercutting,turnthesawoff. When

thebladehascometoacompletestop,unplugthe sawandremovealldebris.

19.NEVERSTARTthesawwiththeworkpieceagainst theblade.

20.NEVERperform"free-hand"operations.Useeither thefenceormitergaugetopositionandguidethe

workpiece.Holdtheworkpiecefirmlyagainstthe mitergaugeorfence.

21.USEa pushstick(s)for rippinga narrowworkpiece.

22.AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause a hand to move into the blade.

23. KEEP arms, hands and fingers away from the blade.

24. NEVER have any part of your body in line with the path of the saw blade.

25. NEVER reach around or over the blade.

26. NEVER attempt to free a stalled blade without first turning the machine "OFF" and unplugging it from

the power source.

29.

PROPERLY SUPPORT long or wide workpiece.

30.

TURN THE SAW "OFF" and unplug from power source. Clean off the table/work area before leav-

ing the saw. LOCK the START/STOP switch with padlock provided to prevent unauthorized use.

31.

ALWAYS position auxiliary fence at least 2-inches in front of saw blade when using auxiliary fence as

a stop when cross cutting.

32.

The right extension wing MUST BE completely assembled and motor cover closed and fastened

before table saw is to be connected to the power source.

33.

ADDiTiONAL iNFORMATiON regarding the safe and proper operation of this product is available

from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201 in the Accident

Prevention Manual for Industrial Operation and also in the Safety Data Sheets provided by the NSC.

Please also refer to the American National Standards Institute ANSi 01.1 Safety Requirements

for Woodworking Machinery and the U.S. Department of Labor OSHA 1910.213 Regulations.

34.

SAVE THESE iNSTRUCTiONS. Refer to them frequently and use them to instruct other users.

Information regarding the safe and proper operation of this tool is available from the following sources:

Power Tool Institute 1300 Summer Avenue

Cleveland, OH 44115-2851 www.powertoolinstitute.org

National Safety Council 1121 Spring Lake Drive

Itasca, IL 60143-3201

American National Standards Institute 25 West 43rd Street 4th floor

New York, NY 10036 www.ansi.org

ANSi 01.1 Safety Requirements for Woodworking Machines, and the U.S. Department of Labor regulations www.osha.gov

AVAILABLE ACCESSORIES

Visit your Sears Hardware Department or see the Sears Power and Hand Tool Catalog for the following acces-

sories. ITEM STOCK NUMBER

* Auxiliary Fence, Rip fence 29878 * Miter Gauge Extension & Stop 29879 * Stock Clamp, Miter Gauge 29880

* Dust Chute with Dust Port 22102 * Micro-Adjustment Assembly 29881

* Table Insert - Standard 29882 * Table Insert - Dado 29885 * Table Insert - Molding Cutterhead 29887

* Saw Blade - Leitz; 10-in. x 40 tooth 29888

variable pitch blade

* Fence Guide System 32371

CONSTRUCTING A FEATHERBOARD

Fig. 2A

24"

Sears may recommend other accessories not listed in this manual.

See your nearest Sears Hardware Department or Sears Power and Hand Tool Catalog for other accessories.

Do not use any accessory unless you have completely read the Owner's Manual for that accessory.

Use only accessories recommended for this table saw. Using other accessories may cause serious injury and

cause damage to the table saw.

Figure 2A illustrates dimensions for making a typical featherboard. The material, which the featherboard is

constructed of, should be straight piece of wood that is free of knots and cracks. Featherboards are used to

keep the work in contact with the fence and table and help prevent kickbacks. Clamp the featherboard to the

fence and table so that the leading edge of the feather- board will support the workpiece until the cut is com-

pleted.

Use featherboards for all non-through cutting opera- tions where the guard and splitter assembly must be removed. Always replace the guard and splitter assembly when the non-through cutting operations

are finished. See figure 2B.

' 5" _1

Fig. 2B

CONSTRUCTING A PUSHSTICK

When ripping work less than 4 inches wide, a pushstick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in figure 2C.

Fig. 2C

The Pushstick should be made of 3/4 or 1/2 inch wood or a thickness less than the width of the workpiece to be cut.

Figure 2C should be copied and scaled so the grids are 1/2 inch square. This copy can be used to make your pushstick.

UNPACKING AND CHECKING CONTENTS Fig. 3-1

The table saw is a heavy machine, two people are required to unpack and lift the table saw.

This table saw w[[[ require some amount of assembly. This table saw and fence is shipped in one carton. This carton also contains a box of saw parts.

1. Remove parts from all of the cartons and lay them on a clean work surface.

2. Two or more people are required to lift the table saw off of the shipping pallet.

3. Remove any protective materials and coatings from all of the parts and the table saw. The protective coatings can be removed by spraying WD-40 on them and wiping it off with a soft cloth. This may need redone several times before all of the protec- tive coatings are removed completely.

CAUTION: DO NOT use acetone, gasoline or lacquer thin- ner to remove any protective coatings on your table saw.

4. After cleaning, apply a good quality paste wax to any unpainted surfaces. Make sure to buff out the wax before assembly.

5. Compare the items to figures below; verify that all items are accounted for before discarding the ship- ping box. If there are any missing parts, call Customer Helpline 1-800-897-7709.

The right extension wing must be completely assem- bled and motor cover closed and fastened before table

saw is to be connected to the power source.

If any parts are missing, do not attempt to plug in the power cord and turn "ON" the table saw. The table saw can only be turned "ON" after all the parts have been obtained and installed correctly.

TABLE SAW

1. Table saw assembly

2. Extension wing, stamped steel (2)

3. Handwheel (2)

4. Handwheel lock knob (2)

5. Splitter mounting rod

6. Splitter bracket assembly

7. Wrench hook

8. Fence hook (2)

9. Poly-V belt

10. Blade guard and splitter assembly

11. Leg assembly (2)

12. Tie bar (2)

13. Switch

14. Saw blade (not shown)

Fig. 3=2 20

21 22 23

FENCE

20. Rip fence assembly

21. Fence front rail, right

22. Fence front rail, left

23. Fence rear rail, right

24. Fence rear rail, left

Fig. 3=3

25. Fence rear rail connector

26. Front rail end cap, right

27. Front rail end cap, left

28. Fence front rail alignment bar (2)

MITER GAUGE

40. Miter gauge

Hardwarepacksarenotidentifiedorlabeled.Seehardwarediagramtohelpinfindingthecorrectpart.Seefigure3-4.

Fig. 3=4

HEX HEAD SCREW _Sx|.a5 x a5ete_ HEX NUT _8xl.a5

@ @8

HEX HEAD SCREW MSxl.a5 × 30rtt,, HEX NUT 5116"-18

@ ® u

EARRIA6E HEAD SCREW 5/|6-|8 X 5/8"

SOuARE HEAD SCREW _BxL25 X 35_ @ I

HEX SOCKET

HEAD CAP SCREW MBx|.25 x 25_

FLAT WASHER _8

HEX SOCKET

HEX HEAD SCREW M6 x 12Be_

ROUND HEAD SELF-TAP SCREW _F4 x B_

ROUND HEAD SELF-TAP SCREW _ × |6_e_

Hardware Pack for Extension Wings (#0R92013) includes:

Flat Washer M8 (8) Lock Washer M8 (8)

Hex Head Screw M8xl.25 x 30mm (8)

Hardware Pack for Rear Rail (#0R92016) includes:

Flat Washer M8 (8) Lock Washer (6)

Button Head Cap Screw M8x1.25 x 25mm (4) Button Head Cap Screw M8x1.25 x 35mm (2)

Hex Nut M8 (2)

Hardware Pack for Front Rail (#0R92017) includes:

Flat Washer M8 (4) Lock Washer M8 (4)

Square Head Screw M8x1.25 x 35mm (4) Hex Nut M8 (4)

HEAD CAP SCREW NSx|,25 x 35_e_

©l

FLAIr WASHER 5/|6"

LOCK WASHER N8

LOCK WASHER 9/|6"

Hardware Pack for Cabinet Legs (#0R92020) includes:

Flat Washer M8 (16) Flat Washer 5/16" (8)

Lock Washer M8 (8) Lock Washer 5/16" (8)

Hex Head Screw M8x1.25 x 25mm (8) Carriage Head Screw 5/16-18 x 5/8" (8)

Hex Nut M8 (8) Hex Nut 5/16" (8)

Hardware for ON/OFF Switch: (Hardware finish is Black Oxide) Hex Head Screw M6 x 12mm (2)

Square Nut M6 (2) Miscellaneous Hardware:

Sheet Metal Screw M4 x 8mm (6) Sheet Metal Screw M4 x 16mm (4)

2 4 5 6 7 8

1. Splitter assembly

2. Blade guard

3. Anti-kickback fingers

4. Blade

5. Align-a-cut insert

6. Rear fence hold down

7. Table surface

8. Rip fence

9. Rear rail

10. lO-in, stamped steel wing

11. Front rail with scale

12. Rip fence lock handle

13. Motor cover

14. Bevel scale

15. Blade height handwheel

16. Handwheel lock knob

17. 3/4 Cabinet

18. Cabinet leg

19. Rubber foot

20. Fence hook

21. On/Off switch

22. Bevel handwheel

23. Bevel handwheel lock knob

24. Miter gauge

25. Miter gauge groove

TOOLS REQUIRED

The following tools are needed for assembly and align- ment. Note: Two blade wrenches and five hex wrenches

are provided with your table saw. The remaining tools are typical shop tools and are not included with your

table saw.

18mm wrench 13mm wrench

10mm wrench

• The table saw is a heavy machine; two people are

required for certain assembly operations.

• DO NOT assemble the table saw until you are sure

the tool is unplugged.

• DO NOT assemble the table saw until you are sure

the power switch is in the "OFF" position.

• For your own safety, DO NOT connect the machine to

the power source until the machine is completely assembled and you read and understand the entire

Owner's Manual.

8mm wrench 3/16-in. hex wrench

#2 Phillips screwdriver

CABINET LEG ASSEMBLY

2. Attach leg assemblies (A) to the front (B) and rear (C) of the table saw cabinet by placing (D) eight

M8 x 25mm hex head screws and eight M8 flat washers down through the mounting holes in the

leg assembly and cabinet (E). Place an M8 flat washer, M8 lock washer and M8 hex nut onto each

of the eight screws attaching leg assembly to cabi- net. Do not completely tighten hardware at this

time. See figure 4-1.

3. Attach two tie bars (F) inside and between front and rear legs already attached to the cabinet with (G) eight 5/16-18 x 5/8" carriage head screws, 5/16" flat

washers, 5/16" lock washers and 5/16-18 hex nuts and securely tighten all hardware. See figure 4-1.

POLY=V BELT ASSEMBLY

MAKE CERTAIN the table saw is disconnected from the power source.

Figure 5=1

MAKE CERTAIN the table saw is disconnected from the power source.

1. Turn the table saw upside down onto its cast iron table. CAUTION: The table saw is heavy; two peo- ple are required for this operation. Be sure to lay cardboard on the floor to protect the table surface.

Figure 44

o " ll

Make sure all packaging material has been removed from inside the cabinet.

Open the motor cover and place the motor Poly-V belt (A) over the blade pulley (B). See figure 5-1.

Carefully lift the motor (C) and place the belt under the motor pulley (not shown). Make sure all the v-

notches in the belt are mated with the v-notches of the blade and motor pulley. See figure 5-1.

Carefully let the motor down and close motor cover.

EXTENSION WiNG ASSEMBLY HANDWHEEL ASSEMBLY

MAKE CERTAIN the table saw is disconnected from the power source.

The right extension wing must be completely assem- bled and motor cover closed and fastened before table

saw is to be connected to the power source.

Figure 64 A

o _

CAUTION: The extension wings are heavy; two people are required to assemble both extension wings to the table saw.

Assemble one of the extension wings (A) to the left side of the table saw. Align the four holes (B) in the extension wing with the four holes in the left side of

the saw table. Use four M8 x 30mm hex head screws, M8 lock washers and M8 flat washers.

Do not completely tighten hardware at this time. See figure 6-1.

MAKE CERTAIN the table saw is disconnected from the power source.

Figure 7=1

Place one of the handwheels (A) onto the bevel shaft (B) located on the side of the cabinet. Align

the groove (C) in the back of the handwheel with the pin (D). See figure 7-1.

Figure 7=2

Figure 6=2

3. Lay a straight edge (C) across the saw table (D) and extension wing (E). Make sure that the front

face of the extension wing (F) is flat to the front face of the saw table (G). Adjust the extension

wing so that its top surface is exactly flat to the saw table and securely tighten hardware. See figure 6-2.

4. Repeat steps 2 and 3 above to assemble the other extension wing to the right side of the table saw.

Thread the locking knob (E) onto the threaded end of the shaft (F). See figure 7-2.

Repeat the steps above to assemble the remaining handwheel and locking knob onto the blade raise/

lower shaft located on the front of the cabinet.

WRENCH AND FENCE HOOK ASSEMBLY Figure 9=2

MAKE CERTAIN the table saw is disconnected from the power source.

Figure 84

3. Place the splitter bracket assembly (C) onto the mounting splitter rod. See figure 9-2 and 9-3.

Figure 9=3

1. Assemble both of the fence hooks (A) to the left side of the cabinet (B) using four M4 x 8mm sheet

metal screws, not shown. See figure 8-1.

2. Assemble the wrench hook (C) above the fence hooks using two M4 x 8mm sheet metal screws, not

shown. See figure 8-1.

BLADE GUARD AND SPLITTER ASSEMBLY

MAKE CERTAIN the table saw is disconnected from the power source.

1. Loosen table insert retainer bolt and remove table

insert.

Figure 94

Place the front attachment point (D) of the blade guard and splitter assembly (H) down into the tool- less front attachment point (E) and the rear attach- ment slot (F) onto the threads of the splitter bracket knob (G); securely tighten splitter bracket knob. Note: The splitter bracket assembly will need to be positioned to fit the blade guard and splitter assem- bly on the mounting splitter rod. See figure 9-3.

2. Place the threaded end of the mounting splitter rod (A) through the hole (B) in the rear of the cabinet.

Place a M12 hex nut (not shown) onto the threaded end of the mounting splitter rod inside of the cabi-

net and tighten securely. See figure 9-1 and 9-2.

Note: Place an 18mm wrench on 12mm hex nut and a 13mm wrench on flats of the splitter rod and tighten.

Remove the hex nut (K) and outer flange (J) from the blade arbor (I). Note: The arbor has a right hand thread; to loosen the hex nut, turn it counterclock- wise. See figure 9-4.

Figure 9=4 Figure 9=6

Place 10" saw blade (Z) onto blade arbor (I); make sure the teeth of the blade are pointing down in the

front of the table saw. Place the outer flange (J) and hex nut (K) onto the blade arbor and snug hex

nut by hand. Place the open-end blade wrench (L) on the flats of the inner blade flange (not shown)

and the box-end blade wrench (M) onto the hex nut and securely tighten. Note: The blade arbor has a

right hand thread; to tighten the hex nut turn it clockwise. See figure 9-4.

Lay a straight edge (R) against the left side of the saw blade (S). Align the splitter (T) so that it is in a

straight line with the blade and tighten the one hex socket head screw (U) on top of the splitter bracket

assembly. See figure 9-6.

Replace table insert and tighten table insert retain- ing bolt removed in step 1.

10.

If there is any problem with the front splitter attach- ment bracket being out-of-square to the saw table

or blade alignment, see "AMGNING SPLITTER BRACKET" in the Operations and Adjustments

section of this manual.

Figure 9=5

Place a square (N) onto the saw table and against the splitter assembly (0) behind the kickback

fingers (P). Make adjustments to the splitter bracket assembly (Q) so that the splitter is square

to the saw table. Once square, tighten the two hex socket head screws on the bottom of the splitter

bracket assembly. See figure 9-5.

RiP FENCE ASSEMBLY

MAKE CERTAIN the table saw is disconnected from the power source.

Figure 10=1

Alignment bars (B) have set screws (A) already

1. Figure 10=3

installed. Make sure set screws are flush with face of alignment bar. See figure 10-1.

Place both fence front rails (C) on the saw table upside down. Make certain that the right fence rail

is on the right-hand side and the left front rail is on the left-hand side. Check that both scales on the

front rails have the 1-inch marking closest to each other. See figure 10-1.

Insert both alignment bars halfway into the back (D) and bottom (E) square nut grooves in the right front rail and slightly snug set screws to hold alignment

bar into the front rail. See figure 10-1.

Slide the left front rail onto alignment bars and against other half of front rail. Make sure both sec-

tions of the front rails are flat and straight to each other. Slightly snug set screws in both alignment

bars. Recheck that the front rail is flat and straight, then securely tighten all set screws.

Figure 10=2

5. Slide the heads of four M8 x 35mm square head screws (F), two from each end of the front rail into

the front rail. Note: The front rail is still positioned upside down on the saw table. Position the screws

so that they will align with the two holes in the front of the saw table and one hole (G) in each extension

wings. See figure 10-2.

6. Place front rail against front of saw table with the four screws going through the four holes in the saw

table and extension wings. Place an one M8 flat washer, M8 lock washer and M8 hex nut onto each of the four screws on the back side of the saw table

and extension wings. Do not completely tighten the four hex nuts at this point.

Raise saw blade (H) and place a straight edge (I) against right side of saw blade extending out over

front of saw table. Align the edge of the right front rail (J) with right side of saw blade using the

straight edge. See figure 10-3.

Figure 10=4

Using a combination square (K), make sure the front rail (L) is level across the saw table and exten-

sion wings, and then securely tighten the four hex nuts. See figure 10-4.

Figure 10=5

s M

Assemble the left side rear rail (M) to the left rear side of the table saw (N). Attach rear rail (M) to

table (N) with two M8 x 25mm hex button head screws, M8 flat washers, and M8 Iockwashers (O).

Attach rear rail to extension wing with one M8 x 35mm hex button head screw, M8 flat washer,

M8 Iockwasher, and M8 hex nut (P). Make sure that the rear rail is below the bottom of the miter

gauge slots (R) in the saw table. See figure 10-5 and 10-6.

10. Slide rear rail connector (S) into the left rear rail already assembled. See figure 10-5.

Figure 10=6

Figure 10=7

13. Assemble the two cursors (U) to the rip fence assembly (V) using four M5 x 16mm pan head screws and M5 lock washers (W). See figure 10-7.

14. Lift up on the rip fence handle (X) and place the fence down onto the saw table with the fence body

into front rail. With the rip fence lock handle up, you can slide the fence back and forth across the saw table. Pushing the rip fence lock handle down, this will lock the fence from moving. See figure 10-7.

15. Align left fence side (AB) at a distance from the right side (AC) of the right miter gauge groove and

lock the fence. See figure 10-7.

16. Use a measuring tape to measure the distance from the saw blade right side to the left fence side.

17. Assemble the cursor (U) to the right side of fence cross arm with two M5 x 16mm pan head screws

and M5 Iockwashers (W). Do not completely tighten screws. See figure 10-7.

11. Slide the right side rear rail (T) onto rear rail con- nector. Assemble the right rear rail with two M8 x 25mm hex button head screws to the saw table

and one M8 x 35mm hex button head screw, M8 flat washer, M8 lock washer and M8 hex nut to the

extension wing. See figure 10-6.

12. Using a combination square, make sure the rear rail is level to the saw table and extension wings and

below the bottom of the miter gauge slots, then securely tighten all hardware.

18. Align cursor with the scale (Z) so that the thin black line (Y) is on the same number as the distance

measured in step 16. Tighten the cursor screws.

19. Remove fence from table and reposition it on left side of saw blade. Align right fence side at a dis-

tance from the left side of left miter gauge groove and lock the fence.

20. Use a measuring tape to measure the distance from the saw blade left side to the right fence side.

21. Assemble the second cursor to left side of fence cross arm with two M5 x 16mm pan head screws

and M5 Iockwashers. Do not completely tighten screws.

22.

Align cursor with the scale so that the thin black line is on the same number as the distance measured in

step 20. Tighten the cursor screws.

Figure 10=8

AA Figure 11=2

23. Note: The rip fence comes with a rear hold down (AA) built into the end of the fence, to keep the rear of the fence from lifting while using a feather board. Engage the rear hold down by simply flipping down

on the hold-down arm so that it is under the rear rail, as shown. See figure 10-8.

24. Check and make sure the rip fence is square to the saw table and is parallel to the miter groove. If any adjustments are needed see "FENCE ADJUST- MENTS" in the Operation and Adjustments section

in this manual.

ON/OFF SWITCH AND END CAP ASSEMBLY

3. Slide the M6 square nuts and switch assembly (E) into the left end of the front rail (F). See figure 11-1.

4. Position the switch assembly to desired location and tighten hardware. CAUTION: Keep switch out

of saw blade path. Most common switch location is to the left side of the saw blade.

5. Place the left front rail end cap (A) into the end of the front rail (B). Attach end cap to rail with two M4 x 16mm sheet metal screws (C). See figure 11-2.

6. Repeat step above to attach right side front rail end cap.

MAKE CERTAIN the table saw is disconnected from the power source.

Figure 11=1

1. Place two M6 x 12mm hex head screws (A) up through the two holes (B) in the switch support (C).

See figure 11-1.

2. Thread two M6 square nuts (D) onto M6 x 12mm hex head screws about three turns. See figure 11-1.

CONNECTING SWITCH CORD TO MOTOR CORD

MAKE CERTAIN the table saw is disconnected from the power source.

Figure 12=1

1. Place the switch cord (A) through hole (B) in front of cabinet. See figure 12-1.

2. Open motor cover, plug switch cord (C) into motor BOLTING TABLE SAW TO THE FLOOR cord (D). See figure 12-2.

Fig. 12-2

Pull slack in switch cord into the cabinet.

Make a loop (E) from the slack of the switch cord and place it behind cord retaining bar (F).

See figure 12-2.

MAKE CERTAIN the table saw is disconnected from the power source.

If you wish, the table saw can be permanently mounted to the floor. To attach to the floor, see instructions

below.

Fig. 12A-1

Remove the four rubber footpads (A) from the table saw legs (B). See Figure 12A-1.

Position the table saw where you want it perma- nently mounted.

Mark the floor through the holes in the bottom of legs.

Move the table saw out of the way and drill pilot holes at the four locations marked.

Attach the table saw to the floor using appropriate hardware (not included).

CAUTION

• A separate electrical circuit should be used for your

table saw. The table saw comes pre-wired for 120-volt use. The circuit should not be less than #14 AWG wire

and should be protected with a 15-amp time lag fuse.

• Have a qualified electrician repair or replace damaged

or worn cord immediately.

• Before connecting the motor to the power line, make

certain the switch is in the "OFF" position and be sure that the electric current is of the same characteristics

as the motor nameplate. All line connections should make good contact.

• Running on low voltage or long extension cords will

damage the motor.

• DO NOT expose the table saw to rain or operate the

in damp locations.

• MAKE SURE all parts have been assembled correct-

ly and are in working order.

• KEEP table surface clear of tools and debris before

starting table saw.

2. To turn the table saw on, press the green "ON" button (A) in one-half inch. Note: There is a safety

feature on the switch to insure that the switch must be completely pressed before the saw will START.

See figure 13-1.

3. To turn the table saw off, press the large red "OFF" paddle (B) or lift the paddle and press directly on

the red "OFF" button. See figure 13-1.

LOCKING ON/OFF SWITCH

1. When the table saw is not in use, the "ON" button should be locked so that it cannot be started.

2. Using the padlock included with your table saw, lift the red "OFF23" paddle and place the padlock

through the holes (C) in the side of the "ON" button and then lock the padlock. Make sure keys have

been removed from padlock and placed where no children can get them. See figure 13-1.

3. To use the table saw, unlock and remove the pad- lock from the "ON" button.

THERMAL=OVERLOAD PROTECTION

STARTING AND STOPPING THE SAW

Figure 13=1

1. The ON/OFF switch is located under the front rail on the table saw.

• Turn the power switch "OFF" and unplug the power cord from its power source prior to doing or perform- ing any maintenance.

• Make certain that the OFF button has been depressed before pushing the thermal overload

reset button.

The motor supplied with your table saw has a resettable thermal-overload relay (D), see figure 13-1. If the motor shuts off during an operation (cutting a workpiece too fast or using a dull blade, using the saw beyond its capacity, or low voltage) press the OFF button and let

the motor cool three to five minutes. Push the reset thermal-overload button on the side of the ON/OFF

switch assembly. Make certain that the saw blade and work area has been cleared of debris before restarting

saw. The motor can now be turned on again.

RAiSiNG AND LOWERING THE BLADE

Figure 14=1

The blade height adjustment handwheel and handwheel lock knob are located on the front of the cabinet above

the blade bevel scale. To raise the saw blade, loosen the handwheel lock knob (A) (counter-clockwise) and

turn the handwheel (B) clockwise. When the saw blade is at its desired height, tighten the handwheel lock knob

(clockwise) until it is securely tightened. See figure 14-1.

ADJUSTING BLADE BEVEL POSITIVE STOPS

Figure 15=1

1. To adjust blade 90-degree blade bevel positive

stop, raise the saw blade (A) to its highest position. See figure 15-1.

To lower the saw blade, loosen the handwheel lock knob (counter-clockwise) and turn the handwheel counter-

clockwise. When the saw blade is at its desired height, tighten the handwheel lock knob (clockwise) until it is

securely tightened.

TILTING THE BLADE The blade bevel handwheel and handwheel lock knob

is located on the left side of the cabinet. To increase the saw blade-bevel, loosen the handwheel lock knob

(A) (counter-clockwise) and turn the handwheel (B) clockwise. When the saw blade is at its desired

degree, tighten the handwheel lock knob (clockwise) until it issecurely tightened. See figure 14-1

To return the saw blade bevel to zero degrees, loosen the handwheel lock knob (counter-clockwise) and turn

the handwheel counter-clockwise. When the saw blade is back to zero degrees it will come into contact with the

adjustable positive stop which will cause the blade to stop. Tighten the handwheel lock knob (clockwise) until it is securely tightened.

2. Using a combination square (B) check that the

blade is 90-degrees to the saw table (zero degrees on bevel scale). See figure 15-1.

3. If the blade will not tilt to 90-degree, turn (counter-

clockwise) the set screw (C) in the left hand side of the saw table until the blade can be positioned to

90-degrees. Tighten bevel handwheel lock knob, located on the left side of the cabinet. This will keep

the blade from further tilting and check that the set screw is contacting positive stop. See figure 15-1.

4. If the blade has been tilted to 90-degrees, tighten

bevel handwheel lock knob, located on the left side of the cabinet. This will keep the blade from further

tilting. Turn the set screw clockwise until it comes in contact with the positive stop.

Figure 15=2

To tilt the blade bevel to 45-degrees, loosen the hand- wheel lock knob (counter-clockwise) and turn the hand- wheel clockwise. When the saw blade is at 45-degrees it will come into contact with the adjustable positive stop which will cause the blade to stop, tighten the hand- wheel lock knob (clockwise) until it is securely tightened.

5. Toadjustblade45-degreebladebevelpositive stop,raisethesawbladeto itshighestposition.

6. Usinga combinationsquare(D)checkthatthe bladeis 45-degreestothesawtable(45-degrees

onbevelscale).Seefigure15-2.

7. Ifthebladewillnottiltto45-degrees,turn(counter- clockwise)thesetscrew(E)intherighthandside

ofthesawtableuntilthebladecanbepositionedto 45-degrees.Tightenbevelhandwheellockknob,

locatedontheleftsideofthecabinet.Thiswillkeep thebladefromfurthertiltingandcheckthattheset

screwiscontactingpositivestop.Seefigure15-2.

8. Ifthebladehasbeentiltedto45-degrees,tighten bevelhandwheellockknob,locatedontheleftside

ofthecabinet.Thiswillkeepthebladefromfurther tilting.Turnthesetscrewclockwiseuntilitcomes

incontactwiththepositivestop.

BEVEL ARROW ADJUSTMENT

1. Make certain that the blade is at 90-degrees to the table surface with a combination square. See

figure 16-1.

BLADE HEEL ALIGNMENT CHECKING BLADE ALIGNMENT

Blade heel is the misalignment of the blade to the miter slots. This means when the blade is not parallel to the miter slots it is heeling. The blade is set parallel at the factory and should not need any adjustments. You can check this by using a dial indicator (not included) or a combination square (not included). It is recommended to check the alignment before initial operation as

follows:

MAKE CERTAIN the table saw is disconnected from the power source.

Fig. 16A-1

Figure 16=1

2. Check that the bevel arrow (A) is pointing to the zero degree mark on the bevel scale (B) located on

the front of the cabinet. See figure 16-1.

3. To adjust arrow, loosen the Philips head screw (C) and reposition the bevel arrow and tighten screw.

See figure 16-1.

Raise the saw blade to its highest point.

Place a combination square (A) on the saw table with one edge (B) of the square against the left

miter slot (C). See Figure 16A-1.

Adjust the square so the rule (D) just touches the saw blade about 1 inch in from the outer diameter.

Make sure the rule is not touching any of the car- bide tips of the saw blade.

Lock the rule in this position.

This dimension should be around 5-1/2 inch, plus or minus 3/32 of an inch.

Fig. 16A-2 Fig. 16B=1

Rotate the saw blade back so that you take the measurement from the same spot on the saw

blade. See Figure 16A-2.

Take a reading at the rear of the blade (E) with the combination square. If there is a difference of more

than four pieces of standard printer paper between the rule and the blade then adjustment will have to

be made.

If an adjustment is necessary see "ADJUSTING BLADE ALIGNMENT".

To align the blade parallel to the miter slot, first loosen two hex head screws (A) under the left side of the table saw. This is the same side as the bevel

handwheel (B). See figure 16B-1.

Fig. 16B=2

ADJUSTING BLADE ALIGNMENT

Blade alignment is factory set and should not need adjustment. All saw blades have some runout. Therefore, readjusting the blade alignment should only be attempted if it becomes necessary (see checking blade alignment).

MAKE CERTAIN the table saw is disconnected from the power source.

Open motor cover located on the right side of the table saw. Loosen two hex head screws (C) locat-

ed directly above the opening. See Figure 16B-2.

The saw table is now loose and can be reposi- tioned until the blade is parallel to the miter slot.

Repeat steps in "CHECKING BLADE ALIGNMENT".

When blade is parallel to miter slot tighten all four hex head screws.

Recheck blade alignment.

Tilt the blade to 45 degrees, and rotate the saw blade by hand. Make sure the blade does not

contact the table insert.

+ 58 hidden pages