Craftsman 113235300 Owner’s Manual

_- Save This Manual _'_

For Future Reference

SWARS

owner's

manual

Model No.

113.235300

Serial Number

Model and serial numbers may be found on a plate

attached to your saw, at the side of the Miter Saw arrn.

You should record both model and serial number in a sate

place for future use

FOR YOUR

SAFETY

READ ALL

INSTRUCTIONS

CAREFULLY

Sears Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A.

Pad No. SP6000

CRi:IFT$1qi:lN

10 INCH COMPOUND

MITER SAW

• assembly

• operating

• repair parts

Printed in Taiwan

FULL ONE YEAR WARRANTY ON CRAFTSMAN BENCH TOP TOOLS

If this miter saw fails due to a defect in materia! or workmanship within one year from the date of pur- chase, RETURN IT TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES, and Sears

will repair it, free of charge. If this miter saw is used for commercial or rental purposes, this warranty will apply for ninety days

from the date of purchase. This warranty applies only while this product is in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817 Wa Hoffman Estates, IL 60179

Safety Instructions For Miter Saw

Safety is a combination of common sense, staying alert and knowing how your miter saw works. Read this manual to understand this miter saw

Safety Signal Words

DANGER: means if the safety information is not followed someone will be seriously injured or killed.

Before Using The Saw

WARNING: to avoid mistakes that could cause

serious, permanent injury, do not plug the miter saw in until the following steps have been satisfac-

torily completed.

• Assembly and alignment (See "Alignment!Adjustment" section )

• Learn the use and function of the ON-OFF switch,

Read the Manual before u._ing this sa'# 5 Kf-ep hancl_ away lro_ the moVll_g blade I DOUBLE INSULATED Wear safety qoClgles that rn_et ANSI Z8 t 1 6 DO hal p_lerm any np_'ralir}n freehand I When serv}ci_g use ,_nly

Stand_Id_ 7 Do no! reach a_ound or behind saw blade II_¢l!_tc_l _replacemel_t parts TIg_qle_ arbor screw and all clamps b_fore 8 Ui}plug _,aw befor_ changincI blacie or serv,circl _lec'trIca_: 120 vr}lts _,aw_ng 9 Fleiease triggsr and wai! for blade 1o s_cp 60 H2 AC only Do no! o_,u ale this saw wllhoul cluards in be!o_e movir_ a workpiece el changing _e_-up 15 ar_ps

Keep Hancls Outside Table Cflrcle:_

Fingers Can Be CUT OFF! ,

_lace 10 TO 8void electric shock, do not expose t_ rain 4980 RPM _'o_f

When Installing Or Moving The Miter Saw

Before moving the saw lock the miter bevel and power head positions Unplug the powerco_d

To avoid back injury, get help when you need to lift the saw more than 10 inches

Never carry the tool by the cord or power head handle Damage to insulation could cause an electric shock

Damage to wire connections could cause a fi_e

Avoid Dangerous Environment. Use the miter saw m dry Indoor place protected from rain Keep work a_-a

we!l Iigt-,ted

Place the saw so neither the user nor bystanders are torced to stand in line with the blade. Thrown debris

COhl]dinjure people in its path

To avoid injury from unexpected saw movement:

• Place the miter saw on a firnq level surface where there

WARNING: means if the safety information ts not fol-

lowed someone could be seriously injured or killed.

CAUTION: means it the safety information is not followed someone might be iniured.

upper and lower blade guards, handle latch, bevel clamp, cover plate stop screw, and fence clamps. (See "Getting to Know Your Miter Saw" section.)

• Review and understand all safety instructions and operating procedures in this manual

• Review the maintenance methods for this miter saw (See 'Maintenance and Lubrication" section.)

Find and read the following labels on the miter saw:

_, WARNING

is plenty of room for handling and properly supporting the workpiece

• Support the miter saw so the table is level and the saw does not rock.

• Bolt or clamp the saw to its supped

• Never Stand On Tool. Serious injury could occur if the tooitips or you accidentally hit the cutting tool Do not

store anything above or near the tool where anyone might stand on the tool to reach them.

To avoid injury or death from electrical shock:

• This Tool Is Double Insulated to give you added pro- tection Double insulation does not take the place or

normal safety precautions when operating this tool When servicing this double insulated tool, use only

identical parts,

• Make sure your fingers do not touch the plug's metal

prongs when plugging or unplugging the miter saw

Before Each Use

Inspect your miter saw. Disconnect The Miter Saw To avoid injury from acci

dental starting, unplug the saw, before changing the setup, changing the blade or adjusting anything

Compare [he direction of rotation arrow on the guard to the direction arrow on the blade. The blade teeth should

always point downward at the front of the saw. Tighten the arbor screw Tighten tile cover plate stop screw Check Damaged Parts. Check for:

Alignment of moving parts, Damaged electric cords, Binding of moving parts,

Broken parts. Stable mounting,

Function of arm return spring and lower guard: Push

the aim all the way down then let _t rise up unti! it stops by itself Check the lower guard to see if tclosed fully If it did not. follow the instructions in the Trouble Shooting section

• Other conditions that may affect the way the miter saw works

Keep Guards In Place In working order and in proper adjustment

If any partofthis miter saw is missing bent. or brokenm any way, or any electrical parts don't work turn the saw off and unplug it. Replace damaged missing _r failed parts before using the saw again

Maintain Tools With Care. Keep the miter saw clesn for best and safest performance Follow instructions for lubn

cating. DON'T put lubricants on the blade while it's spin ning

Remove Adjusting Keys And Wrenches fr)m tool before turning it on

To Avoid Injury From Jams, Slips Or Thrown

• Use Only Recommended Accessories. (See "Sears Recommends The Following Accessories" section)

Consult this Owner's manual for recorT)rT)er;ded acces series. Follow the instructions that come with the

accessories The use of improper accessories may cause risk of injury to persons

• Choose the right !0-inch diameter blade for the mate+ rial and the type of cutting you plan to do

• Make sure the [)lade is sharp undamaged and prop erly aligned. With the saw unplugged, push the power

head all the way down. Hand spin the blade and check for clearance Tilt the power-head to 45 degree bevel and repeat the check If the blade Mts anything, make

Pieces

Cutting Capacity section

• Make sure the blade and arbor coltam ale clean

• Make sure the collars' recessed sides are fa;ing the blade

• Using 1/2-inch box end wrench make sure the arbor cap screw is firrnly t',and tightened

• Make sure all clamps and locks are t_ght and there _s no excessive play m any pads

• Keep Work Area Clean. Cluttered areas and bencher_ invite accidents Floor must not beslippen/

To avoid burns or other tim damage never use the saw near flammable[[quids vapors(rl gases

the adjustments shown in the Maintaining Maximt.m

Plan Ahead To Protect Your Eyes, Hands, Face, Ears

Know Your Miter Saw. Read and understand the owner's manual and labels affixed to the tool Learn its

application and limitations as well as the specific poten- tial hazards peculiar to this tool

To avoid injury from accidental contact with rnoving parts. dent do layout, assembly, or setup work on the miter saw

while any parts are moving Avoid Accidental Starting. Make sure switch is "OFF"

before plugging miter saw into a power outlet Plan your work. Use The Right Tool. Dont force tool or attachment to do

a jot) it was not designed to do Use a different tool for any workpiece that cant be held in a solidly braced, fixed

_osition

CAUTION: This machine is not designed for cut- ting ferrous metals (steel, iron and iron based met- als}. Use this miler saw to cut only wood, wood like products or soft metals like aluminum. Other mate-

rial may shatter, bind on the blade, or create other

dangers.

CAUTION: When cutting any metals, sparks or hot fragments could cause a fire. To avoid this. dis- connect any dust collecting hose from the miter

saw, and remove all traces of wood dust from inside dust traps in the miter saw.

Any power miter saw can throw foreign objects into tne

eyes This car! result in permanent eye damage Wear safely goggles (not glasses) that comply with ANS! Z87 1 (shown on package) Everyday eyeglasses have only impact resistant lenses They are not safety glasses Safety goggles are available at Sears retail stores

Glasses or goggles not in compliance with ANSI Z87 could seriously hurt you when they break

Dress for safety

f i WEAR Y,'3U R

Safety Instructions For Miter Saw (continued)

• Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches) They can get caught and draw

you into moving parts

• Wear nonslip footwear.

• Tie back long hair.

Inspect Your Workpiece

• Make sure there are no nails or foreign objects in the part of the workpiece to be cut.

Plan your work to avoid THROWBACKS - when the

workpiece binds on the blade and is torn from your

hands. Plan the way you will hold tile workpiece from start to fin-

ish: Avoid .awkward operations and hand positions where a

sudden slip could cause fingers or hand to move into the

blade Don't Overreach. Keep good footing and balance

Keep your face and body to one side, out of line with a possible throwback.

Never cut Freehand:

• Cut only one workpiece at a time

• Brace your workpiece solidly against the fence and table lop so it will not rock or twist during the cut

• Make sure there's no debris between the workpiece and its supports

• Make sure no gaps between the workpiece, fence and table will let the workpiece shift after it is cut in two.

• Keep the cut off piece free to move sideways after it's cut oft. Otherwise, it could get wedged against the

blade and thrown violently

• Clear everything except the workpiece and related support devices off the table before turning the miter

SaW on.

• Secure Work. Use clamps or a vise to help hold the work when it's practical.

Use extra caution with large, very small or awkward workpieces:

• Use extra supports (tables, saw horses, blocks, etc.) for any workpieces large enough to tip when not held

• Roll long sleeves above the elbow

• Noise levels vary widely. To avoid possible hearing damage, wear ear plugs or muffs when using miter

saw for hours at a time.

• For dusty operations, wear a dust mask along with

safety goggles.

down to the table top.

• Never use another person as a substitute for a table

extension, or as additional support for a workpiece that is longer or wider than the basic miter saw table or to help feed, support or pull the workpiece.

• Do not use this saw to cut pieces too small to let you

easily hold the work while you keep the thumb side of your index (pointer) finger against the outside edge of

the fence.

• When cutting irregularly shaped workpieces, plan your

work so it will not slip and pinch the blade and be torn from your hands. A piece of molding, for example, must lie flat or be held by a fixture or jig that will not let it twist, rock or slip while being cut.

• Properly support round material such as dowel rods. or

tubing. They have a tendency to roll while being cut. causing the blade to "bite." To avoid this. always use a fixture designed to properly hold your workpiece.

WARNING: If planning to cut aluminum or other

non-ferrous metals: Under adverse conditions, the blade can grab and throw the workpiece suddenly

and unexpectedly. To avoid injury, follow all appli-

cable safety instructions, as you normally would,

and:

• Use only sawblades specifically recommended for non-ferrous metal cutting.

• Do not cut metal workpieces that must be hand held. Use auxiliary clamps or other equipment as

needed.

• Cut non-ferrous metals only if you are experi- enced or under the supervision of an experienced

person.

Whenever Saw Is Running

WARNING: don't allow familiarity (gained from fre-

quent use of your miter saw) cause a careless mis-

take. A careless fraction of a second is enough to

cause a severe injury.

Before starting your cut, watch the miter saw while it runs. If it makes an unfamiliar noise or vibrates a lot, stop immediately Turn the saw off Unplug the saw. Do not restart until finding and correcting the problem.

Keep Children Away Keep all visitors a safe distance from the miter saw. Make sure bystanders are clea_ of

the miter saw and workpiece

Never confine the piece being cut off. Never hold it clamp it, touch it, or use length stops against it while the

blade is spinnmg. It must be free to move sideways on its

own. If confined, it could get wedged against the blade and thrown violently.

Let the blade reach full speed before cutting. Don't Force Tool. It will do the job better and safer at its

designed rate, Feed the saw into the workpiece only fast

enough to let the blade cut without bogging down or binding

Before freeing jammed material:

• Turn switch "OFF"

• Unplug the miter saw.

• Wait for all moving parts to stop.

After finishing a cut:

• Keep holding the power head down

•Release the switch, and wait for all moving parts to stop before moving your hands

• If blade doesn't stop within 6 seconds, unplug the saw and follow the instructions in the Trouble Shooting sec-

tion for fixing the blade brake before using the saw again.

Before Leaving The Saw

Never Leave Tool Running Unattended.Turn power Make workshop child-proof. Lock the shop Disconnect off Wait for all moving parts to stop. master switches Store tool away from children and oth-

ers not qualified to use the tool.

Glossary of Terms for Woodworking

Arbor

The shaft on which a cutting tool is mounted Bevel Cut

An angle cutting operation made through the face of the workpiece.

Compound Cut A simultaneous bevel and miter cutting operation

Crosscut A cutting operation made across the width of the work

piece. Freehand

Performing a cut without the use of fence (guide), hold down or other proper device to prevent the workpiece from twisting during the cutting operation. Twisting of the workpiece can cause it to be thrown

Gum

A sticky, sap based residue frorn wood products.

Heel Misalignment of the blade

Kerr The amount of material removed by the blade in a

through cut or the slot produced by the blade in a non-

through or partial cut.

Miter Cut

An angle cutting operation made across the width of the workpiece. Resin

A sticky, sap based substance that has hardened. Revolutions Per Minute (RPM) The number of turns completed by a spinning object in

one minute. Sawblade Path

The area of the workpiece or table top directly in line with

either the travel of the blade or the part of the workpiece which will be, or has been, cut by the blade. Set

The distance that the tip of the sawblade tooth is bent (or set) outward from the face of the blade

Workpiece The item on which the cutting operation is being per-

formed The surfaces of a workpiece are commonly referred to as faces, ends, and edges.

End

Z_--Edge

Motor Specifications and Electrical Requirements

Power Supply and Motor Specifications The A C motor used on this tool is an universal non-revers

WARNING: To avoid electrical hazards, fire haz- ards or damage to the tool, use proper circuit pro-

tection. Your tool is wired at the factory for Voltage 120 operation using the voltage shown. Connect tool

to a power line with the appropriate voltage and a Amperes 15 15-amp branch circuit. Use a 15-amp time delay Hertz (Cycles) 60

type fuse or circuit breaker. To avoid shock or fire, Phase Single

if power cord is worn or cut, or damaged in any

! way, have it replaced immediately. RPM 4900

ible type, having the following specifications:

Max Developed HP 3

Shaft Rotation Clockwise Brake Automatic

Motor Specifications and Electrical Requirements (continued)

General Electrical Connections

DANGER: To avoid electrocution:

1. Use only identical replacement parts when ser-

vicing. Servicing should be performed by a qualified service technician.

2. Do not use in rain or where floor is wet.

This tool is intended for indoor residential use

only.

110-120 Volt, 60 Hz. Tool Information

Double Insulated

The miter saw is double insulated to provide a double thickness of insulation between you and the tool's electri-

cal system. All exposed metal parts are isolated from the internal metal motor components with protectin_j insula

tion

Polarized Plug Your unit has a plug that looks like the one shown.

To reduce the risk of electrical shock, this appliance has

a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. if the plug does not fit fully in the outlet, reverse plug If it still does not fit contact a qualified electrician to install the proper

outlet. Do not change the plug in any way

WARNING Do not permit fingers to touch the ter-

minals of plug when installing or removing the

plug to or from the outlet.

If power cord is worn or cut, or damaged in any way have it replaced immediately

WARNING: Double insulation does not take the I place of normal safety precautions when operating

this tool.

Motor Safety Protection

IMPORTANT: To avoid motor damage, this motor should be blown out or vacuumed frequently to keep sawdust flora interfering with normal motor ventilation.

1.Connect this tool to a 120v, 15-amp branch circuit with a 15-amp time delay fuse or circuit breaker. Using the

wrong size fuse can damage the motor

2 If the motor won't starL release the trigger switch

immediately. UNPLUG THE TOOL. Check the saw blade to make sure it turns freely. If the blade is free. try to start the motor again. If the motor still does not start, refer to the "Motor Trouble-Shooting Chart."

3 If the motor suddenly stalls while cutting wood, release

the trigger switch, unphlg the tool. and free the blade

from the wood. The motor may now be lestarted and

the cut finished.

Wire Sizes

NOTE: Make sure the proper extension cord is used and is in good condition.

The use of any extension cord will cause some loss of

power To keep this to a minimum and to prevent over- heating and motor burn-out, use the table shown to

determine the minimum wire size (AW.G) extension

cord.

4.Fuses may "blow" or circuit breakers may trip fro quently if:

a. Motor Is Overloaded-Overloading can occur il you feed

too rapidly or make too many staWstops in a short time

b.Voltages not more than 10% above or below the

nameplate voltage can handle normal loads For heavy loads howeve_ the voltage at motor terminals must equal the voltage speciiled on nameplate

5.Most motor troubles may be traced to loose or incorrect connections, overload, low voltage (su(h as small size wire in the supply circuit) or to overly long supply circuit wire, Always check the connections, the load and the supply circuit whenever motor doesn't work wetl Check

wire sizes and length with the Wire Size Chart bel_!w

Extension Wire Sizes Required

i Cord Length for (A.W.G.)

O-25 Ft. 14

26-5O Ft 12

Table of Contents

'v%'arra n[y

Safety "st',_cttuns Fur M_ter 5a_',

Safety S!gnal Words Before Us ng The Saw When nsta nng Dr Mov nc Tr'e Miter 3a',_

Before Each use ToAvod n)u% From Jams ShusOr Thrown Pieces

Plan Ahead To PrntectYou rEdes manr_s Face Ears Dress for safet,

I_spect ¢OLlr Workoqece Whenever Saw s _tmning Be'ore eav ng The Raw

G ossary cf Terms for Woodworking Motor Specifications ano Electrical ae(]dlremenfs

Powe _S.@piy and Motcr SDectflcatlcns General Electrical Connections

119-!2C Volt 60 m/ -oo rfforrratlon

Mater Satety Protection Wre Szes

mabie of Contents Unpack "g anu 2heck no Contepts

Too s Needed

Unpacking Getling To Know four Mite r Saw Ahgnme_t/Adj_,sTme n:s

Unpacking and Checking Contents

Tools Needed

2 Mounhng The Saw ........... 13

2 Safety' Instructions for Basic Saw Operations 15

2 Before Using the Saw ................ 15

2 When !nstalling or Moving the Miter Saw !5

2 Before Each Use .................... 15

3 To Avold lnjury From Jams Slips Or Thrown Pieces .... 16

3 P an Ahead To Protect Your Eyes Hands. Face. Ears 16 3 Dress for safety 16

3 Inspect Your Workpiece 16 _1 Whenever Saw Is Running 17

4 Before Leaving The Saw !7

5 Basic Saw Operahons ........... 18

5 He pful Hints When CuEing Compound Miters .... 22

5 Maintenance And Lubrication ...... 24

6 Lubncation .................... 24

6 Sears Recommends the Following Accesso;les . 24

6 Recommended Accessones ........... 24

6 TroubIeshootmg Guide .......... 25

7 Motor ........... 25

7 General ......... 25

7 VVinng Diagram 26

Maintenance .......... 24

Repatr Darts 28 Notes 34

q::i:il:', 3:',i:i;;J;I

Combination Square

1/2" Wrench

15116" Box End/Open

#2 Phillips Screwdriver

Adjustable Wrench

5/16" Hex "L" Wrench

Wrenches-Two Needed

15t16" Sockets &

Socket Wrenches

Unpacking

WARNING: to avoid injury from unexpected start-

ing or electrical shock, do not plug the power cord

into a source of power during unpacking and assembly, this cord must remain unplugged when- ever you are working on the saw.

This Miter Saw is shipped complete in one box

avoid back injury, get help whenever you have to

I WARNING: although small, this saw is heavy, to I

lift the saw more than 10 inches.

1Remove the miter saw from the carton by lifting the

saw by the base

WARNING: if any part is missing or damaged, do

not plug the saw in until the missing or damaged

part is correctly replaced, to avoid electric shock,

use only identical replacement parts when servic-

ing double insulated tools.

Combination Square Must be True

Straight Edge of

Draw Light Board 3/4" Thick Line on Board This Edge Must be

Along this Edge _,, Perfectly Straight

Should be no Gap or Overlap when Square is Flipped Over in Dotted Position

2.Place the saw on a secure stationary work surface and look the saw over carefully.

3.Mount rubber dust elbow onto the guard

Getting To Know Your Miter Saw

Elbow Upper Blade

Guard Lock Off

Button

Switch

Fence

7 Miter Saw

/ Handle

1 Warning

Label

;) Handle

Latch

Miter Scale 4 Miter Lock

Handle

1.Warning label

2.Handle Latch-The miter saw can be locked in the low- ered position for compact storage

3 Fence Lock Handles-The fence has two positions for

increased crosscut capacity The lock handles secure the fence to the base. The saw is shipped with the fence in the front position.

t" "1

I NOTE: If the fence is being used in the rear position, I

the two fence lock handles must be loosened before

changing the miter angle. Then tighten the fence han-

die at the desired miter angle before starting a cut.

L. J

4. Miter Lock Handle The miter lock handle securely

locks the miter saw at a desired miter angle. Index points have been provided at 0.22 5 R/L, and 45 R/L.

Power Cord

5.Bevel Lock Handle-The bevel lock handle locks the miter saw at a desired bevel angle

6.Lower Blade Guard-The blade guard helps protect your hands from the blade in the raised position To avoid binding on the workpiece, it retracts as the blade

is lowered.

7.Miter Saw Handle-The saw handle contains the trigge_ switch with a lock-off button. The blade is lowered into

the workpiece by pushing down on the handle, The

saw will return to its upright position when the handle is

I released. I 8.OntOff Trigger Switch

To prevent the trigger from being accidentally engaged, a lock-off button is provided. To start the tool, press in the lock-off button and squeeze the trigger.

Release the trigger to stop the miter saw.

3 Fence Lock 5 Bevel Lock

Handle Handle

Alignment/Adjustments

WARNING: To avoid injury from unexpected start- ing or electrical shock, do not plug the saw in. The

power cord must remain unplugged whenever you are working on the saw.

Step One-Blade Square to Table NOTE: The miter saw was assembled aligned, and

irrspected before shipment. Alignment should be checked and any adjustments made to insure accurate cuts.

1Check miter lock handle setting. The miter lock handle

should be at the 0' position. To reset the miter angle, turn the miter lock handle counter clockwise and press

down the index spring.

2.Lower the blade and lock the handle latch Use the combirlation square to check blade squareness to

table. It the blade does not contact the full length of the square, follow the alignment procedure

a Loosen bevel lock handle. b.Grasping metal upper guard, move the cutting head

left or right until blade makes contact with the full length of the square

{: Tighten the bevel lock handle.

3 Check the bevel indicator. If indicator needs adjust-

menl use a phillips screwdriver and slide the indicator

to the 0" on the scale,

Step Two-Checking and Aligning Blade with Turn Table Slot

1 The blade should took like it's parallel to the sides of

the turn table slot. The blade should be 1/8" closer to

left side than right

2If blade looks parallel with turn table slot proceed to

step three If necessary realign blade with turn table slot, adjust as follows.

a. Use a 5/16" hex "L" wrench to loosen (but do not

remove) the two cap screws that attach pivot support

to turn table Move blade power head so it is parallel with turn table slot. Securely tighten cap screws

Recheck blade position and readjust if necessary

Always check blade clearance to table when the

miter saw is tully tilted to the left

Cap

Turn Table

Slot

Alignment/Adjustments (continued)

Step Three-Checking and Adjusting Blade Squareness to Fence (Front Fence Position)

1 To check blade squareness to fence, use a combina-

tion square. Place the square against the fence and

next to the blade as illustrated Place the square so the set in the teeth won't hold it from the blade. The blade

should contact the full length of the square.

2.If blade contacts full length of square, proceed to next step, If blade is not square to the fence, follow the alignment procedure. a,Loosen miter lock handle a half turn. The latch han-

dle should still be secured with blade in lowered posi tion.

NOTE: Take the saw off its stand, bench or plywood base if readjustment is necessary

CAUTION: To keep from losing control of the unit, steady the base with one hand while loosening the two bolts with the other hand.

b.With the unit securely resting on a large stable sur-

face, tilt the unit by lifting up on one side or the other of

the base. Loosen the two miter arm bolts on the

underside of the turn table with a 1/2" wrench or socket Tilt the unit by lifting up on one side or the

other of the base

c. Return the saw to its normal resting position. Make

sure the miter lock handle is loose but do not release the index spring.

d Use the miter saw handle to turn the turn table and

saw so that the blade contacts the full length of the square. Watch out for tooth set. Turn the miter lock

handle clockwise to lock saw square to fence. e.Tilt saw as in Step B and tighten bolts. f. Recheck blade squareness to fence and readjust if

necessary

Adjustment of Miter Scale Indicator

1 Loosen the phillips screw that holds the indicator in

place Reposition the indicator and retighten screw WARNING: do not start the miter saw without checking for interference between the blade and

the turn table structure. Damage could result to the

blade if it strikes the turn table structure during operation of the saw. Broken saw parts could hit you or others.

Step Four-Pivot Adjustments NOTE: These adjustments were made at the factory and

normally do not require readjustment.

1.The miter saw should rise completely to the up position by itself. At least one thread of the bolt should stick out

past the nut. If the saw will not raise by itself or if there

is play in the pivot joints the following adjustments are

necessary.

Travel Pivot Adjustments

a,Hold the pivot bolt with an adjustable or 15/16"

wrench. Loosen the hex lock nut with an adjustable or 15/16" wrench.

b.Recheck the saw travel. Saw should rise freely to its

up travel stop. Check to see that the saw will raise from all positions and there is no looseness in the

pivot. If saw still won't fully rise. have Sears Service check and repair it

Bevel Pivot Adjustment

1.The miter saw should bevel easily by loosening the bevel lock handle and tilting the power head to the left.

At least one thread of the bolt should stick out past the

nut. If movement is tight or if there is looseness in the

pivot follow the adjustment procedure a. Loosen the bevel lock handle.

b Turn the hex lock nut with an adjustable wrench. c Recheck bevel movement of tile miter saw. Read-

just if necessary

Depth Stop The depth stop limits the blades downward travel. It allows the blade to go below the work table enough to

maintain full catting capacities. The depth stop positions the blade 1/4" from the cast iron table support. The depth stop is factory set and should never need adjustment

Maintaining Maximum Cutting Capacity

WARNING: to avoid injury from unexpected start-

ing or electrical shock, do not plug the saw in. The power cord must remain unplugged whenever you are working on the saw.

Unplug the saw before any adjustment is attempted. This tool is factory set to provide maximum cutting capac-

ity for the 10" saw blade provided. When the diameter of the blade has been reduced due to sharpening it may be

necessary to adjust depth stop to provide maximurn cut- ting capacity. When a new blade is installed, it is neces sary to check the clearance of the blade to the turn table

structure.

1.To adjust the depth stop use an adjustable wrench and loosen the hex nut at the rear of the miter saw arm

2Use a fiat blade screwdriver to adjust the depth stop

adJusting bolt. The saw blade is lowered by turning the bolt counterclockwise and raised by turning the bolt

clockwise.

3 Lower the blade into the slot of the turn table Check

blade clearance and maximum cutting distance (dis-

tance from fence where blade enters) to front of turn

table slot Readjust if necessary

Pivot Bolt

Hex Lock

Nut

Adjustable

Wrenches

Depth

Stop

Bevel Lock Adjustable

Handle Wrench

Hex Lock

Nut

WARNING: do not start the miter saw without

checking for interference between the blade and the turn table structure, damage could result to the blade it it strikes the turn table structure during

operation of the saw.

4.Tighten the hex nut with an adjustable wrench while carefully holding the depth stop adjusting bolt with the

flat blade screwdriver so it will not turn while tighteni_lg

hex nut

the depth stop slip and let the blade strike the saw

I WARNING: Failure to tighten the jam nut could let I

Itable. Broken saw parts could hit you or others.

+ 25 hidden pages