CPT CPRT-104 Assembly Instructions Manual
Circle Guide For Router Table
Model: CPRT-104
Web Site: www.circleperfecttools.com
Facebook: www.facebook.com/circleperfecttools
Tutorials: www.circleperfecttools.com/#!VIDEOS/c20ku
FAQ: www.circleperfecttools.com/#!faq/cavw
Contact Us: info@circleperfecttools.com
©2014 Circle Perfect Tools, LLC. All rights reserved
GENERAL SAFETY RULES
Safety is a combination of common sense, staying alert and knowing how to use a tool.
WARNING: To avoid mistakes that could cause serious injury, do not attach Circle Guide for Router Table until
you have read and understood the following:
1.
READ and become familiar with the entire installation instructions on
how to attach Circle Guide for Router Table to your Router table.
2.
LEARN the tool's application, limitations and possible hazards.
3.
REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of
checking to see that keys and wrenches are removed from router table.
before turning ON.
4.
KEEP WORK AREA CLEAN. Clutter areas and benches invite accidents.
5.
DON'T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in
damp or wet locations, or expose them to rain.
Keep work area well lighted.
6.
KEEP CHILDREN AWAY. All visitors should be kept at a safe distance
from work area.
7.
MAKE WORKSHOP CHILDPROOF with padlocks.
8.
DON'T FORCE THE TOOL. It will do the job better and safer at the
rate for which it was designed.
9.
USING THE RIGHT TOOL. Do not force tool or attachments to do a
job for which it was not designed.
10.
USE PROPER EXTENSION CORD. Make sure your extension cord is in condition.
11.
DRESS PROPERLY. Do not wear loose clothing, neckties, or jewelry that
can get caught and draw you into moving parts. Wear protective
hair covering to contain long hair.
12.
ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday
eyeglasses have only impact resistant-lenses, they are NOT
safety glasses.
13.
SECURE WORK. Use clamps or a vise to hold work when practical,
it is safer than using your hand and frees both hands to operate
the tool.
14.
DO NOT OVERREACH. Keep proper footing and balance at all times
15.
DISCONNET TOOLS. When not in use or when changing attachments,
blades, bits, cutter, etc. all tools should be disconnected from
power source.
16.
AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging
in any tool.
17. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF.
DO NOT LEAVE TOOL UNTIL IT COMES TO A COMPLETE STOP.
18.
PROTECT YOUR LUNGS. Wear a face or dust mask if the operation
is dusty.
19.
PROTECT YOU HEARING. Wear hearing protection during extended
periods of operation.
20. KEEP FINGERS AWAY FROM REVOLVING CUTTER.
UNPACKING
This product requires assembly
Carefully remove the product and any accessories from
the box. Makes sure that all items listed in the packing
list are included. Inspect the product carefully to make
sure no breakage or damage occurred during shipping.
1 Centering Bit (Steel) ( .25 inch x 2 1/2) (1) 9 Wood Screws (#8 1 inch) (6)
2 Centering Tool (PVC) (1) 10 Alignment Plate (PVC) (1)
3 Center Pins (PVC/Steel) (3) 11 Slide Plate (PVC) (1)
4 Alignment Pin (Steel) (1) 12 Fender Washer (4)
5 Slide Plate Brackets (PVC) (2) 13 Hex Nuts (1/4" x 20) (4)
6 Brackets (Metal) (3) 14 Hex Key (5/32 SA) (1)
7 Lock Down Knob (1)
8 Mounting/Lock Down Bolts-1/4 inch (6)
ASSEMBLY
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
15 Safety Stops (PVC) (2)
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product. If any parts are damaged or missing, please
contact us via email at info@circleperfecttools.com.
WARNING:
Do not connect power supply until assembly is
complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
Loading...