One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
1. OVERVIEW
CLAA170EA10 is 17.0” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module
composed of LCD panel, driver ICs, control circuit and backlight. By applying 8 bit digital data(6
bit+Hi-FRC),1280×1024, 16.7M-color images are displayed on the 17.0” diagonal screen. Input power
voltage is 5.0V for LCD driving. Inverter for backlight is not included in this module. General
specifications are summarized in the following table:
ITEMSPECIFICATION
Display Area(mm)337.920(H)x270.336(V)(17.0-inch diagonal)
Number of Pixels1280(H)x1024(V)
Pixel Pitch(mm)0.264(H)x0.264(V)
Color Pixel ArrangementRGB vertical stripe
Display Mode normally white, TN
Number of Colors16.7M (6 Bit+Hi-FRC)
Brightness(cd/m^2)250cd/m2(Typ.)(Center point, Lamp current=8.0 mA)
Viewing Angle160 / 160(Typ.)
Surface TreatmentAnti-glare
Power consumption(W)13.1 (Typ.)
Module Size(mm)358.5(W)x296.5(H)x17.5(D)(max)
Module Weight(g)
Backlight UnitCCFL, 2 tables, edge-light(top*1/bottom*1)
1900g(typʼ ˄˃˃
CPT Confidential2/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
2. ABSOLUTE MAXIMUM RATINGS
ITEMSYMBOLMIN.MAX.UNITREMARK
Power Supply Voltage for LCDVCC06V
Lamp VoltageVL540690Vrms
Lamp Current ILO38.5mArms*4). 7)
Lamp FrequencyFL4080kHz
static electricity
Operation TemperatureTop050
Storage TemperatureTstg-2060
Delayed Discharge TimeTD--1sec*8)
[Note]
1).The relative temperature and humidity ranges are as below sketch, 90%RHMax.(Ta40).
2).The maximum wet bulb temperature39(Ta 40) and without dewing.
VESDt-200200V
VESDc-80008000V
*5)
*1). 2). 3). 6)
*1). 2). 3)
3).If you use the product in a environment which over the definition of temperature and humidity too
long to effect the result of eye-aching.
4).The life time of the lamp is related to the current of the lamp, so please according to the description
of the “(b) backlight” on page 7.
5).Test Condition: IEC 1000-4-2
VESDt: Contact discharge to input connector; VESD
: Contact discharge to module
C
6).If you operate the product in normal temperature range, the center surface of panel should be under
60.
7).When lamp current is out of the absolute maximum range, the life will fall rapidly or shown
unusual sign.
IL min 2mA only for test only, but we can’t guarantee the lifetime and performance.
8).Delay lighting testing needs the volt above start voltage Vrms. Before the procedure tube needs
typical lighting for 1 minute and stay in the temperature 25±2 for 24 hours and then testing in the
same condition in dark room.
CPT Confidential3/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
www.panelook.com
Global LCD Panel Exchange Center
y
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
3. ELECTRICAL CHARACTERISTICS
(1).TFT-LCD
Ta=25
ITEMSYMBOLMINTYPMAXUNITRemark
Power Supply Voltage for LCD Vcc4.55.05.5V*1)
Power Supply Current for LCD Icc-700950mA*2)
Permissive Input Ripple VoltageVRP--100mVp-pVcc=5.0V
Differential impedanceZm90100110Ω
Logic input voltage
LVDS:IN+IN-
Common
Mode Voltag
Differential
Input Voltage
Threshold
Voltage(High)
Threshold
Voltage(Low)
VCM1.1251.251.375V
|VID|250350450mV
VTH--100mV
*3)
VTL-100--mV
LCD Inrush CurrentInrush3A*4)
Power consumptionP3.54.75W*2)
[Note]
1).VCC-turn-on conditions:
0.5mst110ms1 sect4
0t250ms200mst5
0t350ms200mst6
Vin=5.0V
4.5V
LCD Power Supply
Logic Signal
0.5V
Backlight Power Suppl
t2
t1
Data: RGB DATA, DCLK, DENA
data
VL
t5t6
VCC-dip conditions:
t3
4.5V
0.5V
0.5V
t4
(1) When 3.6VVcc (min) <4.5V & td10 ms, module works well.
(2) When VCC <3.6 V, VCC-dip conditions should also follow the VCC-turn-on conditions.
CPT Confidential4/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
www.panelook.com
Global LCD Panel Exchange Center
g
t
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
2).Typical current situation: 64 gray scale level,1280 line mode, VCC=5.0V, Fh=64Khz,Fv=60Hz,
f
=54 MHz.
CLK
3).LVDS Signal definition:
VID = VIN
VCM =VCM
VID =VID
– VIN- ,
+
+
–VCM-,
+
–VID-,
VID+ = VIH+–VIH-,
VID- = VIL+–VIL-,
VCM = (VIN
VCM+ = (VIH
VCM- = (VIL
+VIN-)/2,
+
+VIH-)/2,
+
+VIL-)/2,
+
4).Irush Measurement Condition
VIN+= Positive differential DATA & CLK Input
VIN- = Ne
ative differential DATA & CLK Inpu
CPT Confidential5/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
(2).Backlight
1. Electrical specification
ITEMSYMBOLMINTYPMAXUNITREMARK
B/L VoltageVL
B/L Current IL388.5mArms
B/L operating current ILO7.588.5mArms
B/L power consumptionWL
Inverter FrequencyFI455055kHz
Starting Lamp VoltageVS
CPT Confidential6/24
540600649
Vrms
Vrms
IL=8.0mA
Ta=25
*1) Ta=25
*1) Ta=25
9.6
W
IL=8.0mA
Ta=25
*2) Ta=25
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
1600Vrms
1100Vrms
Ta=0
Ta=25
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
2. Lamp life time
ITEM
Lamp life TimeMin. 50,000Min. 50,000Min. 50,000--hr
Rated time
(turn on/off)
ILO at 2.0 mA ILO at 3.0 mA ILO at 8.0 mA ILO at 8.5 mA--
Min.100,000time*4)
UNIT REMARK
[Note ] Measuring inverter TypeCVT SIT-22FA3
If the waveform of light up-driving is asymmetric, the distribution of mercury inside the lamp
tube will become unequally or will deplete the Arm gas in it. Then it may cause the abnormal
phenomenon of lighting-up. Therefore, designers have to try their best to for fill the conditions
under the inverter designing-stage as below:
The degrees of unbalance10%
The ratio of wave height√2 ±10%
Continuous
Operation
*3)
1) Lamp Current measurement method (The current meter is inserted in cold line)
2) a.Frequency in this range can mala the characterisitics of electric and optics maintain in +/- 10%
except hue.
b.If the lamp frequency can be maintain in 50~60KHz, the better charactristics of the electrical
and the optical can be presented.
CPT Confidential7/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
CPTCHUNGHWA PICTURES TUBES, LTD.,
c.If the operating frequency is 40~80 KHz, the life time and the reliability of the lamp will not be
affect.
d.Lamp frequency of inverter may produce interference with horizontal synchronous
frequency,and this may cause horizontal beat on the display.Therefore, please adjust lamp
frequency, and keep inverter as far from module as possible or use electronic shielding
between inverter and module to avoid the interference.
3) Definition of the lamp life time Luminance (L) under 50% of specification starting lamp
voltage or starting lamp voltage is more than 130% of the initial value
4) The condition of Turn-on and Turn-off operation is as below:
a. Lamp current is 8.0mA
b. Frequency is 10 sec.(on)/10 sec.(off)
c. Repeat it for 10 thousand times
d. The result of eye-etching of the lamp hue is normal, and can switch the lamp.
It should not have motion fail when starting lamp voltage is lower than 130% of the initial
value.
5) It is necessary to consider the maximal value when design inverterin order to assure lighting.
6) The equation of power consumption WL=IL x VL x 2.(IL=8.0mATa=25)
7) For keeping good lighting situation, when design the inverter, it must be considered that the
voltage large than starting lamp voltage.
8)WL=IL x VL x2(IL=8.0mATa=25)
9) The Starting Lamp Voltage (VS) of inverter must be driven large than one second.
10) The output voltage of inverter (Vn) must be the same phase of between any lamps.
11) The difference in voltage between any lamps(V) must be smaller than 300V at the same time.
ExampleV300VV =V1(t)-V2(t)
−VLVLVnrms
%15≤
12)
n=12… 4nthe number of lamp
V
˩˄ʻʼ
˩˅ʻʼ
CPT Confidential8/24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
CLAA170EA10-Digital Decade-SPEC-Ver.1-20090715
www.panelook.com
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.