CLAA150XC01 is 15.0" color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module
composed of LCD panel, driver ICs, control circuit and backlight.
By applying 8 bit digital data, 1024×768, 16.7M-color images are displayed on the 15.0"
diagonal screen. Input power voltage is 5.0V for LCD driving.
Inverter for backlight is not included in this module. General specification are summarized in the
following table:
ITEM SPECIFICATION
Display Area(mm) 304.1(H)×228.1(V) (15.0-inch diagonal)
Number of Pixels 1024(H)×768(V)
Pixel Pitch(mm) 0.297(H)×0.297(V)
Color Pixel Arrangement RGB vertical stripe
Display Mode normally white TN
Number of Colors 16.7M(8bits/color)
Brightness(cd/m^2) 300(cd/m2)(Typ.)
Viewing Angle -75~75(H),-60~50(V)(Typ.)
Wide Viewing Angle Technology Optical Compensation Film
Surface Treatment Anti-glare
Electrical Interface CMOS(VIN=3~5V,2 pixel/clock)
Total Module Power(W) 16.5(Typ.)
Optimum Viewing Angle 6 o’clock
Module Size(mm) 326.0(W) ×255.0(H)×15.5(D)
Module Weight(g) 1350(typ)
Backlight Unit 4 CCFLs edge-light(top/bottom)
The LCD Products listed on this document are not suitable for use of aerospace equipment,
submarine cables, nuclear reactor control system and life support systems. If customers intend to use
these LCD products for above application or not listed in "Standard" as follows, please contact our
sales people in advance.
Standard: Computer, Office equipment, Communication equipment, Test and Measurement
equipment, Machine tool, Industrial robot, Audio and Visual equipment, Other consumer
products.
2. ABSOLUTE MAXIMUM RATINGS
ITEM SYMBOL MIN. MAX. UNIT
Power Supply Voltage for LCD VCC 0 7.0 V
Logic input Voltage
Operation Temperature *1) Top 0 50
Storage Temperature *1) Tstg -20 60
ITEM SYMBOLMIN TYP MAX UNIT Remark
Power Supply Voltage for LCD VCC 4.5 5.0 5.5 V Note1
Power Supply Current for LCD ICC - 300 500 mA Note2
Permissive Input Ripple Voltage VRP - - 100 mVp-p Vcc=5.0V
VCC-dip conditions should also follow the VCC-turn-on conditions.
VCC
4.5V
VCC Min
td
[Note 2] Typical current situation : 256-gray-bar pattern, 768 line mode, VCC=+5.0V
(b)Backlight
3
CPT Confidential
/18
CLAA150XC01 - 2003/06/10
CPT CHUNGHWA PICTURES TUBES, LTD.,
p
p
ITEM SYMBOL MIN TYP MAX UNIT REMARK
Lamp Voltage VL - 570 - V IL=6.0mA
Lamp Current IL 3.5 6.5 8.0 mA Note1
Interter Frequency FL 40 - 70 kHz Note2
Starting Lamp Voltage VS
Lamp life Time LT - 50000 - hr
1400 - - V
1200 - - V
Ta=0℃
Ta=25℃
Note3
IL=6.0Ma
Continuous
Operation
[Note 1]
Lamp Current measurement method ( The current meter is inserted in cold line)
[Note 2]
Lamp frequency of inverter may produce interference with horizontal synchronous
frequency,and this may cause horizontal beat on the display.Therefore,please adjust
lamp frequency,and keep inverter as far from module as possible or use electronic
shielding between inverter and module to avoid the interference.
The degrees of unbalance: less than 10%
The ratio of wave height: less than
√2 ±10%
I
I-
The degrees of unbalance = Ip-I-p /Irms*100(%)
The ratio of wave height = Ip(or I-p)/Irms
Ip: lamp current high side peak, I-p: lamp current low side peak
[Note 3]
Definition of the lamp life time
Luminance: L under 50% of specification
Starting Lamp Voltage: VS < 1400V, Ta=0