CPS FT806A Series, FT800FN Series, FT806M Series Owner's Manual

OWNER’S MANUAL

ECCENTRIC CONE FLARING TOOLS

FT800FN,FT806A,FT806M Series

FEATURES

• Forms a burr-free 45° flare.

• Suitable for soft materials such as copper and aluminum.

• FT800FN designed specifically for R-410A systems

• Heat treated, black oxide finished steel flaring bars

• Precision machined yoke assembly incorporating a 3/8” sq. drive

• Professional grade 3/8” sq. drive ratchet and carrying case included

Yoke Handle

Yoke

Stop Screw

3/8” Drive Ratchet

Flaring Bar

Clamp Handle

Protective Carrying Case

OPERATION INSTRUCTIONS

ECCENTRIC TYPE FLARING TOOL

Angle: 45°
Uses: Suitable for soft copper tube, aluminum tube and other soft tubes, etc.

1) Turn both yoke and clamp handles counter-clockwise until yoke slides freely. Move yoke to
far end of flaring bar up against the stop screws (Fig. 1).

2) Spread flaring bar and insert tube into hole that corresponds to tube diameter. Close bar
and position tube approximately 1mm above horizontal plane of flaring bar (Fig 2 & Fig.3).

3) Slide yoke above tube, align red arrow on yoke with positioning mark on flaring bar. Turn
clamp handle clockwise to tighten and secure (Fig. 4).

4) Use supplied ratchet or manually turn yoke handle clockwise until clutch releases.
Continue to turn another 2-3 revolutions (Fig. 5).

5) Turn yoke handle counter-clockwise until free from flared tubing. Loosen clamp handle and
slide yoke to end of flaring bar. Spread flaring bar and remove tube (fig. 6).

*Always wear eye protection and hand gloves when working with hand tools.

clamp
handle

flaring bar

flaring bar

yoke

yoke handle

Fig. 1

flaring bar

Fig. 2

0-1 mm

arrow

positioning mark

Fig. 4

Fig. 5

tube

Fig. 3

Fig. 6

MAINTENANCE INSTRUCTIONS

1. Keep 45° place of the circular cone clean away from copper dust after using (Fig. 7).

2. Apply lubricating grease to all threaded parts on the yoke.

3. Apply lubricated grease to the bearing located under the flaring cone mechanism.

circular cone

brush

SPARE PARTS

FTX800B410 R-410A bar: 3/16, 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 inch
FTX800BA Standard imperial bar: 3/16, 1/4, 5/16, 3/8, 1/2, 5/8 and 3/4 inch
FTX800BM Standard metric bar: 6, 8, 10, 12, 15, 16 and 18 millimeter
FTX800R 3/8” sq. drive ratchet
FTX800Y Yoke assembly.

1010 East 31st Street, Hialeah, Florida 33013, USA,

Tel: [phone], Fax: [phone]

www.cpsproducts.com. e-mail: [e-mail]

4605 Crysler Ave. Niagara Falls, Ontario L2E 3V6

Phone - 905-358-3124; Fax - 905-358-7187

Toll Free - 1-866-629-3895; e-Mail: [e-mail]

109 Welland Avenue, Welland, South Australia 5007

Tel: [phone], Fax: [phone]

Ruby Industrial Complex #06-10, Genting Block 80 Genting Lane

CPS PRODUCTS, INC.

CPS CANADA

Krijgsbaan 241, 2070 Zwijndrecht, Belgium
T

CPS PRODUCTS N.V

el: (323) 281 30 40; Fax: [phone]

CPS AUSTRALIA PTY. LTD.

e-mail: [e-mail]

CPS ASIA

Singapore 349565

el: (65) 8461056, Fax: [phone]

T

e-mail: [e-mail]

FT800OM

Bedienungsanleitung

Exzentrischer Konus für Bördelgerät

Metrische Version,Inch Version,Speziell für R-410-A Systeme

Merkmale

• Fertigt einen gradfreien Bördel

• Einsetzbar für weiche Materialien, wie z.B. Kupfer, Aluminium

• FT800FN ist speziell für R-410A gefüllte Systeme geeignet

• Wärmebehandelt, Schwarz oxidiert, aus Stahl hergestellte Bördelleiste

• Maschinell hergestellter Börderkörper inkl. einen 3/8“ Vierkant Antrieb

• Einschließlich mit professionellen 3/8“ Ratschenschlüssel und Tragekoffer

Bördel-Handgriff

Bördelkörper

Begrenzungs-Schraube

3/8“ Ratschenschlüssel-Antrieb

Bördel-Leiste

Arretierungs-Drehgriff

Tragekoffer