Coyote CJAKTCS30, CJAKTCS36, CJAKTCC2 Instructions

25

1

/2"

C2SL36 INSTALL GUIDE

DIMENSIONAL RENDERINGS

32

1

/2"

23"

1

/2"

35

1

20

10 1/4"

/2"

35

32 1/2"

35 3/4"

3

/4"

22

1

/8"

20 1/2"

22 1/8"

/8"

5

37

Overall Product Dimensions

Model No. Height Width Depth

C2SL36

CJAKTCS36

 When using a Coyote insulated jacket, you will want to build your island to the jackets Cutout and Overall Dimensions

listed above (detailed on 2nd page). Once the jacket is installed, the grill will rest on/inside the insulated jacket

Model No. Gas Supply BTU's Regulator WC Pressure Max PSI Electrical Requirements

C2SL36LP Propane 90,000

C2SL36NG Natural Gas 90,000

23"

11"

35 1/2"

37 5/8"

23"

11"

25 1/2"

23"

20 lb Tank Regulator

1/2" Female Pipe

utout Dimensions for Island

C

Model No. Height Width Depth

C2SL36

CJAKTCS36

11" .5 PSI Qty 1 - 120 VAC 60 Hz Grounded Plug
4" .5 PSI Qty 1 - 120 VAC 60 Hz Grounded Plug

10 1/4"

11"

11"

Important Note to Installer This file is not intended to replace your Owners' Manual which contains specific safety

requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your builtin grill.

www.coyoteoutdoor.com

C2

SL36 INSTALL GUIDE

NON-COMBUSTIBLE CONSTRUCTION

Insulated Jacket NOT Required

1 1/2"

GRILL

24"

10 1/4"

OPENING

HEIGHT

INCLUDING

COUNTERTOP

24"

20 1/2"

OPENING

DEPTH

TOP VIEW

CONNECTION

32 1/2"

OPENING WIDTH

2 1/2"

GAS

OPENING

2"

G

2 1/2"

21/2"

G

1 5/8"

24"

1 1/2"

GRILL

OVERHANG

1 1/2" MIN

COMBUSTIBLE CONSTRUCTION

Insulated Jacket Required - Model # CJAKTCS36

7

/8"

LINER

OPENING

4 1/8"

GAS

CONNECTION

2 3/4"

G

4 1/8"

4 1/8"

G

1 3/4"

7

/8"

JACKET

OVERHANG

1 1/2" MIN

11"

OPENING

HEIGHT

22 1/8"

OPENING

DEPTH

TOP VIEW

35 3/4"

OPENING WIDTH

DOORS / DRAWERS

OPENING WIDTH

FRONT VIEW

 Combustible material can not be within 24" of the grills frame
 This applies to all directions - horizontal & vertical
 Shaded area above on "TOP VIEW" illustrates the 24" minimum

requirement (not to scale for rendering purposes)

 The grill is designed to hang from the counter top with no support

underneath

 Minimum rear clearance for the hood to open is 2"
 If you have a wall/partition behind the grill, the minimum rear clearance

to that wall should be at least 7" to allow for ventilation of the exhaust

 Regardless if you are using a combustible or non-combustible building material, you must include at least two vents within

the island.

 These vents must be at least 20 sq. in. each and allow fresh air to move from the grill cabinet to the exterior environment.
 For a propane setup, the vents should be installed lower as propane is heavier than air.
 For a natural gas setup, the vents should be located higher in the island, as natural gas is lighter than air.
 Do not locate the two vents on the same wall of the island. Cross ventilation is key to allow any excess heat or trapped

gas to dissipate.

OPENING

HEIGHT

Ventilation Requirements:

Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety

requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill.

INCLUDING

COUNTERTOP

 If using combustible material within 24" of the grill frame, you MUST use

the corresponding Coyote Insulated Jacket

 Using a insulated jacket, does not waive any other standard installation

procedure (ventilation, connections, etc)

 The jacket is designed to hang from the counter top with no support

underneath

 Minimum clearance for hood to open is 2"
 If you have a wall/partition behind the grill, the minimum rear clearance

to that wall should be at least 7" to allow for ventilation of the exhaust

DOORS / DRAWERS

OPENING WIDTH

FRONT VIEW

OPENING

HEIGHT

www.coyoteoutdoor.com