Page 1
RIDE-ON MOWER
Models
A14011M
16.5HP, 19.5HP B&S 32” & 38”
A14111M
16HP HONDA 32” & 38”
OWNER/OPERATORS MANUAL
READ THIS MANUAL BEFORE OPERATING MACHINE
DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS IN
THIS MANUAL ARE FOLLOWED
NOTE: Bring this Manual when Service & or Warranty work is required.
Revised 05/04/2013
Page 2
11 June 2015 Page 2 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
ISSUED BY:
ISSUED TO:
OWNERS INFORMATION
MACHINE CODE NO:__________________________
SERIAL NO:_______________________
Located on label inside transmission housing
B&S ENGINE MODEL NO:______________TYPE____________ CODE_______________
HONDA ENGINE TYPE NO:____________________SERIAL NO____________________
Located on engine refer Engine Owners Manual
DATE OF PURCHASE:__________________________________
OWNERS NAME:
ADDRESS:
TOWN/CITY:
STATE:
AUTHORISED DEALER/
DISTRIBUTOR:
ADDRESS:
TOWN/CITY:
STATE:
PRE DELIVERY CHECK LIST
Check parts Assemble Service Instruction
LAWN BOSS
ALWAYS KEEP THIS MANUAL IN A SAFE PLACE.
Page 3
11 June 2015 Page 3 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Read, understand, & follow all instructions in the
Owner/Operators manual.
Know the controls and how to stop the engine
quickly in an emergency.
Allow only responsible adults, who are familiar with
the instructions in this manual, to operate the machine.
Clear the area to be mowed of loose objects such as
sticks, stones, bones, wire, toys, debris, etc., which
could be picked up and thrown by the blades.
DO NOT mow whilst people, especially children, or
pets are in the mowing area.
DO NOT mow either direction on slopes beyond 15
degrees (1 in 3.75).
Exercise extreme caution on slopes.
Reduce speed on slopes and in sharp turns to pre-
vent overturning or loss of control.
Start or stop slowly when on slopes.
Mow up and down slopes, not across the slope.
Stay alert for holes or bumps in the terrain and other
hidden hazards.
Watch out for traffic when crossing or operating the
mower near roadways.
Stop the blades rotating before crossing surfaces
other than grass.
When using attachments, never direct discharge of
material toward bystanders nor allow anyone near
the machine while it is in operation.
Before leaving the operators position-
a] Disengage all clutches and secure cutting units;
b] Return drive pedal to neutral position and set the
parking brake;
c] Stop the engine and remove the key.
Disengage drive to attachments and stop engine-
a] Before refueling;
b] Before checking, cleaning or working on the
mower;
c] After striking a foreign object (check the mower
for damage and make repairs before restarting and
operating the equipment);
d] If machine starts to vibrate abnormally (check
immediately).
Disengage drive to attachments when transporting or
not in use.
A mower operator should be in good physical and
mental health and not under the influence of alcohol
or any drug which might impair vision, co-ordination
or judgment.
Never mow while barefoot or wearing open sandals
or thongs. Wear long trousers and heavy shoes.
It is advisable to wear suitable eye protection when
operating a mower.
Mow only in daylight or good artificial light.
Before using, always visually inspect to see that
blades, bolts and cutter assembly are not worn or
damaged. Replace worn or damaged blades and
bolts in sets to preserve balance.
Check all nuts, bolts, and screws often; always be
sure the mower is in safe operating condition.
Keep safety devices (guards and switches) in place
and in working order.
Never use the mower unless the guards provided by
the manufacturer, are in position.
Ensure any replacement parts used comply with the
original manufacture’s recommendations and specifi-
cations.
Replace worn or faulty silencers.
Keep machine free of grass, leaves or other debris,
excessive oil, grease, or spilt fuel. These can be a
fire hazard.
Refuel outdoors only. Do not smoke while fueling
engine. Never remove the cap of the fuel tank or add
petrol while the engine is running or the engine is
hot. Remove fuel cap slowly to relieve any tank pressure. If fuel is spilled, do not attempt to start the
engine but move machine away from the area of the
spill and avoid creating any source of ignition until
fuel vapors have dissipated.
Check for fuel leaks while refueling, before and while
using the mower. If a fuel leak is found, do not start
or run the engine until the fuel leak is fixed and
spilled fuel is wiped away.
Do not operate engine in a confined space where
exhaust fumes (carbon monoxide) can collect.
Always mount the mower from the left or the oppo-
site side to the discharge chute.
Start the engine carefully with the cutting means dis-
engaged.
Do not over-speed the engine or alter governor set-
tings. Excessive speed is dangerous and shortens
mower life.
Stop the engine whenever you leave the mower,
even for a moment.
Store the mower in a well-ventilated room away from
naked flames such as may be found in hot water
heaters.
Do not lend or sell the mower, without the owners/
operators Manual.
SAFETY INSTRUCTIONS
Page 4
11 June 2015 Page 4 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Roll Pin type steering wheel
PRE-DELIVERY INSTRUCTIONS
INTRODUCTION:
The purpose of this procedure is to ensure the dealer/
distributor has made the necessary installations, adjustments and checks, before the machine is operational. This
procedure begins upon receiving the crated mower and is
finalised once the mower has been either sold or leaves the
dealer/distributors premises. This is the minimum amount of
work required, however it should not be limited to only the
areas detailed in this procedure.
RESPONSIBILITY:
It is the responsibility of the dealer/distributors to ensure
that before a machine is delivered to a customer, it is in
perfect operational condition.
PROCEDURE:
CHECK ACCESSORIES SUPPLIED IN SEAT PROTECTION BAG
Engine owners manual
Owner/Operator manual
Ignition keys (AM015)
Spark plug spanner (AM295)
Spark plug spanner (AM005G0 16HP Honda)
Spark plug Spanner 13HP Honda
Tommy bar (AM007)
Steering wheel (SW13)
Roll Pin (DP10)
Set Screws M8X20 X 2
Nuts M8 Nyloc x 2
Seat Springs x 2 (13060)
Washer W05M202 x 2
Warranty Card
Pre-delivery Instruction Sheet
Remove the four seat bolts, shakeproof washers and plain
washers to remove the plastic bag protection from around
seat. Install the four seat bolts, shakeproof washers and
plain washers, making sure that the seat is adjusted into the
desired position by using the seat transmission slots, tighten
bolts.
TYRE PRESSURE
Before operation ensure that all tyre pressures are equal.
The maximum pressure allowed is 140 kpa (20 P.S.I.).
ENGINE OIL
Before operation ensure that engine oil level is to the full
mark on the dipstick. (Check engine owners manual if oil
needs to be added).
FUEL TAP
Ensure the fuel tap at the bottom of the LH side of fuel tank
is turned to the on position before attempting to start engine. (Use unleaded fuel only).
Turn off fuel tap after use.
ASSEMBLE STEERING WHEEL TO MOWER
Roll Pin Type—To attach the steering wheel, align the hole
in the steering wheel boss to the hole in the steering shaft
and use a hammer and suitable punch to drive the DP10 roll
pin in, through the hole in the steering shaft cover into the
steering wheel and shaft. Ensure that the pin is situated
centrally in the steering wheel boss and that the steering is
free to turn.
Keyed Type— Remove tape attaching woodruff key to
steering shaft. Remove the screw & washers attached to
the steering shaft. Lubricate taper on steering shaft with
grease or anti-seize. Place steering wheel with keyway
aligned with woodruff key on shaft. Assemble the screw and
washers onto the shaft with 1/2”a/f socket, extension &
wrench & tighten to 23Nm.
Press the steering wheel center cover into place using hand
pressure only.
SEAT SPRINGS
Install and tighten the two seat springs, bolts and nuts to
the bracket welded to the rear of the chassis, which is situated under the seat/transmission cover.
SAFETY SWITCHES
Park brake switch - With cutter lever disengaged, attempt
to start the engine without setting the park brake. Engine
should not start.
Disengagement Switch - While sitting on machine with
park brake set and cutter engaged, attempt to start machine. Engine should not start.
Seat Switch - While sitting on machine start engine, engage cutter and lift weight from seat. Engine should cut
out.
CUTTER BELT
Ensure that when the cutter belt is in the disengaged position that the belt does not overlap when squeezed together,
if this occurs adjust the cutter engage lever until correct
disengagement is achieved.
Bonnet shown in closed
position underneath dash
pa n el e x t e n s i o n b e f o r e
attaching bonnet strap.
Roll Pin type steering wheel
Page 5
11 June 2015 Page 5 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
IMPORTANT
RECOMMENDED FUEL
Unleaded fuel is recommended by all manufacturers of
engines fitted to Cox products.
SAFETY MICRO SWITCHES
Before operating machine, ensure that all micro-safety
switches are operating correctly. Do not operate machine
with faulty, missing or damaged safety micro-switches.
STARTING MACHINE
When starting machine; Ensure parking brake is set. Ensure
that cutter is disengaged, otherwise electric starter motor will
not engage. If engine is cold move throttle to cold start
position and return to desired throttle setting when engine
starts. Do not attempt to operate engine with throttle lever in
cold start (choke) position. (Note electric start engines fitted
with recoil can be manually started with cutter disengaged
and ignition on).
BLADE WARNING
Do not use mowing attachment with broken or bent blades,
damaged or worn bolts and nuts or damaged cutter disc,
otherwise damage and premature wear will result from
vibration. Replace blades, bolts and nuts only in pairs to
maintain correct balance. Recommended blade nut torque is
36-40Nm. Do not over tighten.
Keep both feet and hands clear at
all times of the mowing attachment
while attempting to start or operate
the machine.
WARNING
DO NOT OPERATE WITHOUT MOWING
ATTACHMENT DEFLECTOR FITTED & DOWN.
Safety footwear is recommended when operating machine.
Mount and dismount only from left hand side of machine.
Reference to left or right hand side of machine is determined
by sitting in the operating position on the machine.
Ensure machine has parking brake engaged when attempting
to start engine.
Never allow engine revs to exceed more than 3600 RPM.
TO OPERATE
BEFORE STARTING/SWITCHING OFF:
See Engine Maintenance/Instruction Sheet. When stopping
engine disengage cutter return throttle to slow position and
switch off
ENGAGING & DISENGAGING MOWING ATTACHMENT:
The Disengaging lever is situated on the right hand side by
the steering column. Before starting, disengage mowing
attachment by pulling lever fully to the operator. Before
engaging mowing attachment ensure cutter height
adjustment is in high position. Select preferred cutting height
after engaging mowing attachment. For safety it is advisable
at all times, other than when mowing, that the mowing
attachment be kept in the disengaged position.
TO DRIVE FORWARD/REVERSE:
Power is regulated by the throttle, set throttle control to
desired engine power. Press down on the forward section of
the drive pedal for forward movement, on the rear of the
drive pedal for reverse. The amount of movement controls
the ground speed, less movement from the neutral position
results in less ground speed, use this feature especially in
heavier conditions.
MANOEUVRING:
The forward and reverse operation makes the machine very
manoeuvrable and the sharpest turns can be negotiated easily
and quickly, however;
Owing to the hydrostatic transmission, when manoeuvring the
machine you must allow the machine to come to a complete
stop before moving off in the opposite direction. This means
that if you are travelling forward and need to reverse out of
an area etc, you must return the pedal to the neutral position
come to a complete stop and then select reverse drive and
Vice Versa for travelling from reverse to forward.
TO BRAKE:
The drive pedal may be used to slow/brake the machine. If
travelling forward ease the pedal back into the neutral
position and the machine will slow and stop. When travelling
in reverse ease the pedal forward into the neutral position.
Should a failure to drive occur during operation use the brake
pedal situated on the left side of the mower.
PARKING AND TRANSPORTATION BRAKE:
TO ACTIVATE: Fully depress the brake pedal situated at the
left side of the mower. Raise park brake knob protruding out
of the right hand side of the console and release brake pedal
to engage the park brake in lock & release knob. Depress
pedal and the mechanism will release.
Do not engage parking brake unless the machine has
completely stopped.
Do not attempt to drive with park brake engaged.
CUTTING HEIGHT ADJUSTMENT:
The height adjustment lever is located on the left hand side of
the machine and may be altered to suit varying conditions.
NOTE: When mowing slopes, keep drive pedal in
forward or reverse, depending on direction of travel.
The low gearing will prevent it from picking up
excessive speed. If very steep it may be necessary to
throttle back slightly and /or, decrease pedal travel.
OPERATING INSTRUCTIONS
!
Page 6
11 June 2015 Page 6 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
It is the owner’s responsibility to ensure that all-periodical
checks, necessary adjustments and services are carried out.
STOP ENGINE - Never attempt any maintenance with
the engine running, remove spark plug lead and ensure
the blades have stopped rotating. Before servicing,
disconnect spark plug wire and ground it, disconnect battery at
negative terminal, to prevent accidental starting.
1. OIL CHANGING & FILTER REPLACEMENT (ENGINE): See
Engine Maintenance/Instructions Sheet and carry out as per Engine
Manufacturers Recommendations.
SERVICING ENGINE AIR CLEANER FOAM PRE-CLEANER— See
engine owners manual for correct method to check and service engine air
cleaner and or foam pre-cleaner.
TRANSAXLE— Type of Oil- top up with 10w30 oil At 50 hours replace
with 5W50 synthetic oil and every 250 hours thereafter— Quantity
2300mls.
2. LUBRICATION OF MACHINE: Lubrication of machine must be
carried out every 25 hours of operation or once a month, whichever falls
first. More frequently when operated under adverse conditions.
A. OILING: A few drops of oil should be placed at the following
points: Steering linkages and pivot points, disengaging linkages and
height adjustment mechanism.
B. CHAIN: Use only chain lube for lubrication of the steering
chain.
3. TO CHECK BLADES: Stop engine. Remove spark plug lead.
Side Discharge Only, lift deflector and height adjustment control to
highest position. If necessary simply remove the blade bolt and nut
using a suitable spanner and replace worn parts.
4. ENGINE TO PTO VEE BELT ADJUSTMENT: Loosen the four
engine mounting bolts. Move engine forward and adjust belt firmly.
Do not over tension. While maintaining tension on the engine
re-tighten bolts. Check belt tension at machine service period
(25hrs B&S) (50hrs Honda) or more frequently under heavy mowing
conditions.
5. PTO TO CUTTER VEE BELT ADJUSTMENT: Tension is
automatically adjusted by the belt tensioning springs. However, as
the belt stretches it will be necessary to lower the rear of the cutter
housing by loosening the rear lifting link nut, and visa versa when a
new belt is fitted.
6. CUTTER HEIGHT ADJUSTMENT: If the Mowing Attachment can
not be positioned to give a satisfactory grass cut height using the
available notches on the chassis the adjustable link can be used to
raise the Mowing Attachment to the desired height. Position the
mower on a smooth level surface and engage the mowing
attachment, lock the park brake on, and lower the Mowing
Attachment to the notch above the desired cut height. Place equal
height spacers of the desired height under the mowing attachment
that can support the mowing attachments weight and lower the
Mowing Attachment onto them. Loosen the 2 Screws located
together on the front of the Rear Link located below the front of the
left foot rest. Push the Rear Link rearwards until it stops and
retighten the 2 screws. Adjust the rear lifting link located on the
middle rear of the mowing attachment by tightening the nut until it
just lifts the rear oif the mowing attachment of the spacers. Lift the
Mowing attachment off the spacers and remove the spacers and
check the cut height is as desired and the deck is level to slightly
higher (3—5 mm) at the back. Adjust height again if required.
7. CUTTER BRAKE ASSEMBLY ADJUSTMENT: With
disengagement handle in engaged position and mowing attachment
in low cut, normal clearance between cutter head pulley and cutter
head brake pad is approximately 3mm (1/8"). To adjust clearance,
remove 'R' pin from brake pull rod, adjust to give required
clearance, replace brake pull rod and 'R' pin. Check operation after
adjustment.
8. DISENGAGING ADJUSTMENT: With the engine switched off,
engage the mowing attachment, then fully lower. Place a straight
edge vertically against the front of the front axle beam and in line
with the disengagement lever. Measure the distance between the
straight edge and the 8mm dia pin fitted with the small ‘R’ pin for
the threaded adjuster. Disengage mowing attachment and using the
same method, check the new distance. The difference should be 20
– 22mm. Engage mowing attachment, remove ‘R’ pin and adjust
threaded adjuster accordingly. Install ‘R’ pin and re-check
measurement. Due to normal wear in transmission to cutter vee
belt, the disengagement lever will move lower and touch the foot
rest. When this occurs the amount of travel will need to be readjusted. If a new vee belt is installed the above settings will apply.
Start engine and raise cutter to full height stop, cutter belt should
not engage. If this occurs switch off engine, engage cutter then
screw adjuster out 1 – 2 turns then retest.
9. TO ADJUST STEERING CHAIN: Adjust chain by loosening the
four bolts which hold the steering idler shaft mounting brackets
(AM255) in position, slide forward to tension chain then retighten
bolts.
10. TO REMOVE MOWING ATTACHMENT: Fully lower mowing
attachment and engage, remove weight compensating spring,
remove 'R' pin from rear lifting link and disconnect, remove ‘R’ pin
from cutter brake adjusting rod and disconnect, disengage mowing
attachment, remove belt, remove front pivot pin, Turn steering
wheel to the left to slide out mowing attachment. To refit, reverse
the above.
11. MOWING ATTACHMENT VEE BELT ADJUSTMENT: Automatic
by springs on mowing attachment.
12.TYRE PRESSURE: 140 Kpa (20.P.S.I.) approximately front and
rear. Uneven pressure can give an uneven finish when mowing and
may cause damage to tyres and/or tubes.
13. BATTERY MAINTENANCE: Maintain electrolyte fluid level just
above plates by topping regularly with distilled water. When not in
use, a battery discharges by as much as 1% a day, more when the
climate is warm. To make up for this loss, a boosting charge should
be given once a month. Disconnect battery terminals to charge,
then allow to stand minimum 1/2hr before re-connecting (re-check
electrolyte level). If a battery is not used for a period of more than
three (3) months, the terminals should be disconnected and trickle
charged at two (2) amps for two (2) hours once every three (3)
months or before use.
14. SEAT ADJUSTMENT: Loosen four seat mounting bolts and slide
seat into desired position in slots and re-tighten bolts.
15. CLEANING AND POLISHING POLYETHYLENE BONNET
AND REAR MUDGUARD: To keep scratches on bonnet and
mudguard to minimum, do not rub or brush off with bare hands, use
a soft cloth or a light flow of compressed air. For dirt, wash with a
steady stream of water only (no detergent), then blow off excess
water with air. To polish remove excess dust or dirt. When surface
is dry, spray on an automotive type plastic preservative and leave on
for 30 to 60 seconds. Using a dry soft cloth (i.e. cheesecloth) wipe
off to bring up lustre.
16. GENUINE SPARE PARTS: Always use Genuine Cox Factory
Made Spare Parts. Use of non-genuine COX spares will void your
warranty.
17. SAFETY FIRST: The use of any mechanical appliance can cause
injury if incorrect procedures are used. Please ensure that all family
members of intended operators read this manual thoroughly.
TORQUE SETTINGS
1/4” UNC BOLT/NUT 10Nm (84lbf in)
5/16” UNC BOLT/NUT 20Nm (180lbf in)
3/8” UNC BOLT/NUT 36Nm (27lbf ft)
7/16” UNF BOLT 68Nm (50lbf ft)
6mm BOLT/NUT 9Nm (80lbf in)
20mm NUT 100Nm (74lbf ft)
5/8” UNF NUT 100Nm (74lbf ft)
MAINTENANCE INSTRUCTIONS
We are proud that you have purchased a Cox product and urge you to follow these instructions
to obtain the maximum life for your machine. If in doubt check with your supplier.
Page 7
11 June 2015 Page 7 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
BEFORE EXTENDED STORAGE
BEFORE EXTENDED STORAGE
BEFORE EXTENDED STORAGE
MAINTENANCE SCHEDULE
BEFORE EACH USE & EVERY 5 HOURS
BEFORE EACH USE & EVERY 5 HOURS
BEFORE EACH USE & EVERY 5 HOURS
Check engine oil level, adjust if required
Check engine air cleaner foam pre-cleaner, service if required
Check engine rotating screen/finger guard, clean if required
Check operation of safety switches, service if required
Check foot brake operation
Check tyre pressures, adjust if required
Check for loose fasteners, tighten if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s,
housing, and guards for wear or damage, replace if required
Check transaxle vent cap and oil
Change engine oil - Clean machine - Lubricate as per required
DATE / / HOURS..........................DEALER................................................
EVERY 5 HOURS
EVERY 5 HOURS
EVERY 5 HOURS
Check engine oil level, adjust if required
Check engine air cleaner foam pre-cleaner, service if req.
Check engine rotating screen/finger guard, clean if required
Check operation of safety switches, service if required
Check foot brake operation
Check tyre pressures, adjust if required
Check for loose fasteners, tighten if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
1 MONTH OR 5 HOURS W
1 MONTH OR 5 HOURS W
1 MONTH OR 5 HOURS W
HICH EVER OCCURS FIRST
HICH EVER OCCURS FIRST
HICH EVER OCCURS FIRST
Change engine oil
Check engine air cleaner foam pre-cleaner , service if required
Check engine rotating screen/finger guard, clean if required
Check foot brake operation, adjust if required
Check operation of safety switches, service if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,
and guards for damage, replace if required
Check and adjust engine to transmission vee belt if required..
Check for loose fasteners, tighten if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
DATE / / HOURS.......................CUSTOMER................................................
3 MONTH OR 25 HOURS
3 MONTH OR 25 HOURS
3 MONTH OR 25 HOURS
WHICH EVER OCCURS FIRST
WHICH EVER OCCURS FIRST
WHICH EVER OCCURS FIRST
Change engine oil if operating under heavy load or high ambient temperature Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check foot brake operation
Check operation of safety switches and replace if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,
and guards for wear or damage, replace if required
Check and adjust engine to transmission vee belt if required..
Check battery condition, service if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
Check for loose fasteners, tighten if required
*Service more often under dusty conditions, or where air borne debris is present
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS..........................DEALER................................................
Change engine oil if operating under heavy load or high ambient temperature
Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check foot brake operation
Check operation of safety switches and replace if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,and guards for wear or damage, replace if required
Check for loose fasteners, tighten if required
Check and adjust engine to transmission vee belt if required..
Check battery condition, service if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
6 MONTH OR 50 HOURS
6 MONTH OR 50 HOURS
6 MONTH OR 50 HOURS
WHICH EVER OCCURS FIRST
WHICH EVER OCCURS FIRST
WHICH EVER OCCURS FIRST
Page 8
11 June 2015 Page 8 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
9 MONTHS OR 75 HOURS WHICH EVER OCCURS F
9 MONTHS OR 75 HOURS WHICH EVER OCCURS F
9 MONTHS OR 75 HOURS WHICH EVER OCCURS F
IRST
IRST
IRST
Change engine oil if operating under heavy load or high ambient
temperature
Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check foot brake operation
Check operation of safety switches and replace if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,
and guards for wear or damage, replace if required
Check for loose fasteners, tighten if required
Check battery condition, service if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
Check and adjust engine to transmission vee belt if required.
12 MONTHS OR 100 HOURS WHICH EVER OCCURS FIRST
12 MONTHS OR 100 HOURS WHICH EVER OCCURS FIRST
12 MONTHS OR 100 HOURS WHICH EVER OCCURS FIRST
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS...............CUSTOMER/DEALER................................................
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS................CUSTOMER/DEALER................................................
18 MONTHS OR 150 HOURS WHICH EVER OCCURS FIRST
18 MONTHS OR 150 HOURS WHICH EVER OCCURS FIRST
18 MONTHS OR 150 HOURS WHICH EVER OCCURS FIRST
Change engine oil filter
Change engine oil
Check engine spark plug, clean, adjust, or replace if required
If fitted clean engine exhaust spark arrester
Check engine air cleaner foam pre-cleaner , service if required *
Check engine air cleaner cartridge, service if required*
Clean engine cooling system*
Replace in-line fuel filter
Check foot brake operation
Lubricate stub axles Check for loose fasteners, tighten if required
Check operation of safety switches, service if required
Check tyre pressures, adjust if required
Check steering chain an sprockets or wear, adjust if required
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
Re-tension rear wheel retaining nut/s
Check battery condition, service if required
Check belts for wear or damage, replace if required
Check and adjust engine to transmission vee belt if required..
Check transmission to cutter vee belt and adjust cutter housing
level if required
15 MONTHS OR 125 HOURS WHICH EVER OCCURS FIRST
15 MONTHS OR 125 HOURS WHICH EVER OCCURS FIRST
15 MONTHS OR 125 HOURS WHICH EVER OCCURS FIRST
DATE / / HOURS..........................DEALER................................................
*Service more often under dusty conditions, or where air borne debris is present
Change engine oil if operating under heavy load or high ambient temperature
Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check operation of safety switches and replace if required
Check foot brake operation
Lubricate stub axles Check tyre pressures, adjust if required
Check battery condition, service if required
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
Check for loose fasteners, tighten if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
Check and adjust engine to transmission vee belt if required..
21 MONTHS OR 175 HOURS WHICH EVER OCCURS FIRST
21 MONTHS OR 175 HOURS WHICH EVER OCCURS FIRST
21 MONTHS OR 175 HOURS WHICH EVER OCCURS FIRST
Change engine oil if operating under heavy load or high ambient
temperature
Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check foot brake operation
Check operation of safety switches and replace if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,
and guards for wear or damage, replace if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
Check and adjust engine to tranmission vee belt if required..
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS...............CUSTOMER/DEALER................................................
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS..........................DEALER................................................
Change engine oil
If fitted clean engine exhaust spark arrestor
Check engine air cleaner foam pre-cleaner , service if required *
Check engine rotating screen/finger guard , clean if required *
Check engine air inlet console screen , clean if required *
Check foot brake operation
Check operation of safety switches, service if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check steering chain an sprockets or wear, adjust if required
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
Check belts for wear or damage, replace if required
Check mowing attachment brake pad for wear, replace if required
Check clutch arm action, adjust if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check and adjust engine to transmission vee belt if required..
Check Transmission to cutter vee belt and adjust cutter housing level if
required
Page 9
11 June 2015 Page 9 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
*Service more often under dusty conditions, or where air borne debris is present
Change engine oil if operating under heavy load or high ambient temperature
Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check foot brake operation
Check operation of safety switches and replace if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,
and guards for wear or damage, replace if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
Check and adjust engine to transmission vee belt if required..
24 MONTHS OR 200 HOURS WHICH EVER OCCURS FIRST
24 MONTHS OR 200 HOURS WHICH EVER OCCURS FIRST
24 MONTHS OR 200 HOURS WHICH EVER OCCURS FIRST
Replace engine oil filter
Change engine oil
Check engine spark plug, clean, adjust, or replace if required
If fitted clean engine exhaust spark arrestor
Check engine air cleaner foam pre-cleaner , service if required *
Check engine air cleaner cartridge, service if required
Clean engine cooling system*
Check foot brake operation
Check operation of safety switches, service if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check steering chain and sprockets for wear, adjust if required
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
Check belts for wear or damage, replace if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check and adjust engine to transmission vee belt if required..
Check transmission to cutter vee belt and adjust cutter housing level if
required
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS..........................DEALER................................................
27 MONTHS OR 225 HOURS WHICH EVER OCCURS FIRST
27 MONTHS OR 225 HOURS WHICH EVER OCCURS FIRST
27 MONTHS OR 225 HOURS WHICH EVER OCCURS FIRST
DATE / / HOURS................CUSTOMER/DEALER................................................
30 MONTHS OR 250 HOURS WHICH EVER OCCURS FIRST
30 MONTHS OR 250 HOURS WHICH EVER OCCURS FIRST
30 MONTHS OR 250 HOURS WHICH EVER OCCURS FIRST
Change engine oil
If fitted clean engine exhaust spark arrestor
Check engine air cleaner foam pre-cleaner , service if required *
Check engine rotating screen/finger guard , clean if required *
Check foot brake operation
Check operation of safety switches, service if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check steering chain an sprockets or wear, adjust if required
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
Check belts for wear or damage, replace if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check and adjust engine to transmission vee belt if required..
Check transmission to cutter vee belt and adjust cutter housing level if
required
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS..........................DEALER................................................
33 MONTHS OR 275 HOURS WHICH EVER OCCURS FIRST
33 MONTHS OR 275 HOURS WHICH EVER OCCURS FIRST
33 MONTHS OR 275 HOURS WHICH EVER OCCURS FIRST
Change engine oil if operating under heavy load or high ambient
temperature
Check engine air cleaner foam pre-cleaner, service if required *
Check engine rotating screen/finger guard, clean if required *
Check foot brake operation
Check operation of safety switches and replace if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing ,
and guards for wear or damage, replace if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check transmission to cutter vee belt and adjust cutter housing level if
required
Check and adjust engine to transmission vee belt if required..
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS.................CUSTOMER/DEALER................................................
36 MONTHS OR 300 HOURS WHICH EVER OCCURS FIRST
36 MONTHS OR 300 HOURS WHICH EVER OCCURS FIRST
36 MONTHS OR 300 HOURS WHICH EVER OCCURS FIRST
Replace engine oil filter
Change engine oil
Check engine spark plug, clean, adjust, or replace if required
If fitted clean engine exhaust spark arrestor
Check engine air cleaner foam pre-cleaner , service if required *
Check engine air cleaner cartridge, service if required
Clean engine cooling system*
Check foot brake operation
Check operation of safety switches, service if required
Check tyre pressures, adjust if required
Lubricate stub axles
Check steering chain an sprockets or wear, adjust if required
Check mowing attachment cutter blades, bolts, nuts, disc/s, housing,
and guards for wear or damage, replace if required
Check belts for wear or damage, replace if required
Check battery condition, service if required
Check for loose fasteners, tighten if required
Check and adjust engine to transmission vee belt if required..
Check transmission to cutter vee belt and adjust cutter housing level if
required
*Service more often under dusty conditions, or where air borne debris is present
DATE / / HOURS..........................DEALER................................................
Page 10
11 June 2015 Page 10 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Chassis & Components 13HP HONDA, 16.5HP & 19.5HP B&S ONLY for serial nos before
CR9605S S/N 3058, CR9607S S/N 10082, CR9610S S/N 521, CR9611S S/N 986, CR9612S S/N 211
Page 11
11 June 2015 Page 11 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
ITEM PART NUMBER DESCRIPTION QTY
1 NM6NT Nut 2
2 NM8NT Nut 7
3 SH0820M Screw 6
4 SH0620M Screw 3
5 W06MN Washer 5
6 SPPK6X20 Screw, Pan 2
7 W040818 Washer 2
8 SPPK5X16 Screw, Pan 7
9 WSR12 Washer, Seal 7
10 W030820 Washer 7
11 A141173L Nose, Bonnet 13HP Honda Only 1
A140073L11M Nose, Bonnet 1
12 96043 Cowl, Bonnet 1
13 WS040816 Washer, Lock, Spring 5
14 SH0616M Screw 5
15 13060 Spring, Seat 2
16 W05M202 Washer 2
17 A119214L08L Stand, Tank, Fuel 1
18 A131009 Cover, Shaft, Steering 1
19 SPPK5X16 Screw, Pan 2
20 96114 Strap, Bonnet 2
21 PR04M4.8 Rivet 2
22 NCM5X2.5X9.5 Nut, Cage 2
23 NCM6X1.6X9.5 Nut, Cage 2
24 96044 Mudguard 1
25 A135021L Door, Console 1
26 A116109 Sub-Assy, Seat 1
27 A116009L Mount, Seat, Medium 1
28 90112 Seat Switch Mounting Plate 1
29 SP1PNCSM Switch, Plunger 1
30 SPST04CX0.37 Screw, Pan 3
31 SH0816M Screw 4
32 WS050216 Washer, Lock, Spring 4
33 W052003 Washer 4
34 A139036L Cover, Rear 1
35 NCM6X1.6X9.5 Nut, Cage 3
36 A140075B Baffle, Hot Air, Bonnet, B&S, 19.5 1
37 SPM6X12 Screw, Pan 2
38 W06MN Washer 2
39 NM6NT Nut 2
Chassis & Components 13HP HONDA, 16.5HP & 19.5HP B&S ONLY for serial nos before
CR9605S S/N 3058, CR9607S S/N 10082, CR9610S S/N 521, CR9611S S/N 986, CR9612S S/N 211
Page 12
11 June 2015 Page 12 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Chassis & Components 13HP HONDA, 16.5HP & 19.5HP B&S ONLY for serial nos from
CR9605S S/N 3058, CR9607S S/N 10082, CR9610S S/N 521, CR9611S S/N 986, CR9612S S/N 211
Page 13
11 June 2015 Page 13 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Chassis & Components 13HP HONDA, 16.5HP & 19.5HP B&S ONLY for serial nos from
CR9605S S/N 3058, CR9607S S/N 10082, CR9610S S/N 521, CR9611S S/N 986, CR9612S S/N 211
ITEM PART NUMBER DESCRIPTION QTY
1 NM6NT Nut 2
2 NM8NT Nut 6
3 SH0820M Screw 6
4 SH0620M Screw 2
5 W06MN Washer 5
6 SPPK6X20 Screw, Pan 2
7 W040818 Washer 2
8 SPPK5X16 Screw, Pan 7
9 WSR12 Washer, Seal 7
10 W030820 Washer 7
11 A141173L Nose, Bonnet 13HP Honda Only 1
A140073L11M Nose, Bonnet 1
12 96043 Cowl, Bonnet 1
13 WS040816 Washer, Lock, Spring 5
14 SH0616M Screw 5
15 13060 Spring, Seat 2
16 W05M202 Washer 2
17 A119214L08L Stand, Tank, Fuel 1
18 A131009 Cover, Shaft, Steering 1
19 SPPK5X16 Screw, Pan 2
20 96114 Strap, Bonnet 2
21 PR04M4.8 Rivet 2
22 NCM5X2.5X9.5 Nut, Cage 2
23 NCM6X1.6X9.5 Nut, Cage 2
24 96044 Mudguard 1
25 A135021L Door, Console 1
34 A139036L Cover, Rear 1
35 NCM6X1.6X9.5 Nut, Cage 3
36 A140075B Baffle, Hot Air, Bonnet, B&S, 19.5 1
37 SPM6X12 Screw, Pan 2
38 W06MN Washer 2
39 NM6NT Nut 2
40 A140009L Mount, Seat 1
41 W0620HD Washer 4
42 13247 Washer 4
43 WS06081.5 Washer, Lock, Spring 4
44 B0620C Bolt 4
45 BHSSC0410 Screw, Button 2
46 WS040816 Washer, Lock, Spring 2
47 W040818 Washer 2
48 AM16512F Switch, Seat 1
48.1 SP1PNCSM Switch, Plunger 1
49 A140110 Seat 1
Page 14
11 June 2015 Page 14 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Chassis & Components 16HP HONDA ONLY for serial nos before CR9604T S/N 456, CR9606S S/N 2098
Page 15
11 June 2015 Page 15 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
ITEM PART NUMBER DESCRIPTION QTY
1 A141040L Bumper, Front 1
2 SH0816M Screw 6
3 NM8NT Nut 8
4 13060 Spring, Seat 2
5 W05M202 Washer, Flat 2
6 SH0820M Screw 2
7 NM6NT Nut 4
8 A119075B Baffle, Hot Air, Bonnet, Front 1
9 SPPK5X16 Screw, Pan 7
10 A119073L10G Nose, Bonnet, Sloping 1
11 WSR12 Washer, Seal 7
12 W030820 Washer, Flat 7
13 96043 Cowl, Bonnet 1
14 W051216 Washer, Flat 2
15 WS050216 Washer, Lock, Spring 4
16 W052003 Washer, Flat 4
17 SH0620M Screw 4
18 W06MN Washer, Flat 4
19 SPPK6X20 Screw, Pan 2
20 NHCM8 Nut 2
21 W040816 Washer, Flat 1
22 SH0616M Screw 1
23 W041216 Washer, Flat 4
24 NHM6 Nut 2
25 A131009 Cover, Shaft, Steering 1
26 SPPK5X16 Screw, Pan 2
27 WS040816 Washer, Lock, Spring 3
28 96114 Strap, Bonnet 2
29 PR04M4.8 Rivet 2
30 NCM5X2.5X9.5 Nut, Cage 2
31 96044 Mudguard 1
32 A116009L11D Mount, Seat, Medium 1
33 90112 Seat Switch Mounting Plate 1
34 A116110 Seat, Medium 1
35 SP1PNCSM Switch, Plunger 1
36 SPST04CX0.37 Screw, Pan 3
37 A135021L Door, Console 1
38 NCM6X1.6X9.5 Nut, Cage 3
39 A139036L Cover, Rear 1
40 SH0612M Screw 2
Chassis & Components 16HP HONDA ONLY for serial nos before CR9604T S/N 456, CR9606S S/N 2098
Page 16
11 June 2015 Page 16 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Chassis & Components 16HP HONDA ONLY for serial nos from CR9604T S/N 456, CR9606S S/N 2098
Page 17
11 June 2015 Page 17 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Chassis & Components 16HP HONDA ONLY for serial nos from CR9604T S/N 456, CR9606S S/N 2098
ITEM PART NUMBER DESCRIPTION QTY
1 A141040L Bumper, Front 1
2 SH0816M Screw 2
3 NM8NT Nut 8
4 13060 Spring, Seat 2
5 W05M202 Washer 2
6 SH0820M Screw 2
7 NM6NT Nut 4
8 A119075B Baffle, Hot Air, Bonnet, Front 1
9 SPPK5X16 Screw, Pan 7
10 A119073L10G Nose, Bonnet, Sloping 1
11 WSR12 Washer, Seal, Epdm Rubber 7
12 W030820 Washer 7
13 96043 Cowl, Bonnet 1
14 W051216 Washer 2
17 SH0620M Screw 4
18 W06MN Washer 4
19 SPPK6X20 Screw, Pan 2
20 NHCM8 Nut, Hex, Conelok 2
21 W040816 Washer 1
22 SH0616M Screw 1
23 W041216 Washer 4
24 NHM6 Nut 2
25 A131009 Cover, Shaft, Steering 1
26 SPPK5X16 Screw, Pan 2
27 WS040816 Washer, Lock, Spring 3
28 96114 Strap, Bonnet 2
29 PR04M4.8 Rivet 2
30 NCM5X2.5X9.5 Nut, Cage 2
31 96044 Mudguard 1
37 A135021L Door, Console 1
38 NCM6X1.6X9.5 Nut, Cage 3
39 A139036L Cover, Rear 1
40 SH0612M Screw 2
41 A140009L Mount, Seat 1
42 W0620HD Washer 4
43 13247 Washer 4
44 WS06081.5 Washer, Lock, Spring 4
45 B0620C Bolt 4
46 BHSSC0410 Screw, Button 2
47 WS040816 Washer, Lock, Spring 2
48 W040818 Washer 2
49 AM16512F Switch, Seat 1
49.1 SP1PNCSM Switch, Plunger 1
50 A140110 Seat 1
Page 18
11 June 2015 Page 18 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Steering Components
Page 19
11 June 2015 Page 19 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Steering Components
ITEM PART NUMBER DESCRIPTION QTY
1 13242 Pin, Pivot, Front Axle 1
2 B0850M Bolt 2
3 NM8NT Nut 4
4 13203 Axle, Stub, Left 1
5 13204 Axle, Stub, Right 1
6 AM336 Washer, Sealing, Shaft 2
7 C02 Circlip 2
8 GNTF3 Nipple, Grease 2
9 A139032 Wheel 2
9.1 VSS Valve, Tubeless 1
9.2 BB204212N Bearing, Ball 2
9.3 AM021 Sleeve, Spacer, Bearing 1
10 W20MN Washer, Flat 2
11 13107 Washer 2
12 WS06081.5 Washer, Lock, Spring 2
13 SH0620F Screw 2
14 A116060 Cap, Hub 2
15 AM255 Steering Idler Shaft Mtg Brkt 2
16 AM215 Idler Bush 2
17 90271 Idler, Steering 1
18 AM256 Tie Rod Inc. Nuts 2
18.1 N06F Nut 2
19 RE38INTSTUD End, Rod 2
20 AM337 End, Rod 2
21 N06FC Nut 4
22 B0624F Bolt 2
23 AM018 Chain, Steering 1
24 95006 Shaft, Steering, Lower 1
25 C05 Circlip 1
26 W092016 Washer, Flat 1
27 AM017C1 Steering Shaft Bush With Collar 2
28 89100 Fastener, Pushon 1
29 89097 Steering Shaft Yoke 2
30 OC21 "O" Clip 2
31 AM25399J Disc, Universal Joint 1
32 A131087Z Shaft, Steering, Upper 1
33 13012 Bush, Flanged, Nylon 1
34 A131089Z Shaft, Steering, Top 1
35 B0630M Bolt 1
36 W041216 Washer, Flat, Bright 6
37 NM6N Nut 1
38 W122414 Washer, Flat 1
39 B0625M Bolt 4
40 NM6NT Nut 6
41 DP10 Pin, Roll 1
42 SW13 Wheel, Steering, 13" Incl Cover 1
43 SW13T Wheel, Steering, 13", 3/4" Taper Hub+ Cover 1
44 A131109Z Shaft, Steering, Top, 3/4" Taper 1
45 SK09 Key, Woodruff 1
46 W052003 Washer, Flat 1
47 WS050216 Washer, Lock, Spring 5
48 SH0512F Screw 1
49 W05M202 Washer, Flat 6
50 SH0512C Screw 4
51 A139103L Beam, Axle, Front 1
Page 20
11 June 2015 Page 20 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Drive Components
Page 21
11 June 2015 Page 21 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Drive Components
ITEM PART NUMBER DESCRIPTION QTY
1 Sub-Assy, PTO 1
2 A116013 Cushion, Drive 1
3 A116025 Spline, Driven, Cushion, Large 1
4 89048 Washer 1
5 A139012 Transaxle, Hydro 1
6 14022 Bracket, Thrust, Hub 2
7 B0860M Bolt 4
8 W05M202 Washer 4
9 W051218 Washer 4
10 NM8NT Nut 4
11 W203806 Washer 2
12 A116139 Wheel 2
12.1 VSS Valve, Tubeless 1
12.2 TT16X 650-8SS Tyre, Tubeless 1
13 W122414 Washer 2
14 C02 Circlip 2
15 A116060 Cap, Hub 2
16 14126 Key 2
17 A139092Z Guide, Belt, Left 1
18 A139094Z Guide, Belt, Right 1
19 B0830M Bolt 4
20 WS050216 Washer, Lock, Spring 4
21 W051218 Washer 11
22 B0850M Bolt 1
23 90293 Boss, Idler 1
24 90294 Boss, Idler 1
25 PIFBB126598A Idler, Flat 1
26 NM8NT Nut 6
27 A108103 Spacer, Pulley, Engine 1
28 A108101 Pulley, Engine 1
29 A108104 Key 1
30 GS0505C Screw, Set 1
31 W072004 Washer 1
32 WS071006 Washer, Lock, Spring 1
33 W071416 Washer 1
34 SH0720F Bolt 1
35 B0860M Bolt 4
36 B0840M Bolt 1
37 A111018 Spring, Extension 1
38 89052 Control Rod 1
39 A111013L Pedal, Drive 1
40 AM230 Bush - Plastic 2
41 W052003 Washer 1
42 RP01 Pin, 'R' 1
43 A116015Z Pivot, Pedal, Drive 1
44 SH0616M Screw 2
45 W041216 Washer, Flat 2
46 NM6NT Nut 2
47 CP2-512 Pin, Split 1
48 14157 Fastener, Push On, Round 1
49 A111017Z Pin, Locking, Brake+Drive 1
50 A111050Z Bush, Pin, Locking 1
51 14038 Knob 1
52 V55 Belt V 1
53 96051 Rod, Select Free Wheel 1
54 RP04 Pin, 'R' 1
55 V13 Belt, V (32” cut only) 1
56 W092016 Washer 1
Page 22
11 June 2015 Page 22 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Drive PTO Components
Page 23
11 June 2015 Page 23 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Drive PTO Components
ITEM PART NUMBER DESCRIPTION QTY
1 A139024 Pulley, PTO, Socket, Cushion 1
2 BB305513NS Bearing, Ball 2
3 A139031 Sleeve, Spacer, Bearing 1
4 A139025 Fan, Transaxle 1
5 SPM4X12 Screw, Pan 3
6 W04MN Washer, Flat 3
7 WSM4X1.2X1.2 Washer, Lock, Spring 3
8 A139026L Mount, PTO, Vented 1
9 A139028Z Retainer, Recessed, Bearing 1
10 CHSBM10X75 Bolt, Cap 1
11 NM10NT Nut 1
12 W10MN Washer, Flat 1
13 A116013 Cushion, Drive 1
14 A116025 Spline, Driven, Cushion, Large 1
15 89048 Washer 1
16 T1A646083060 Washer, Wave 1
17 W092016 Washer 1
Page 24
11 June 2015 Page 24 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Transaxle Components
Page 25
11 June 2015 Page 25 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Transaxle Components (TUFF TORQ)
ITEM PART NO. DESCRIPTION QTY
1 A139012 Transaxle 1
3 T1A646084163 Lower Case 1
4 T1A646024460 Reservoir Tank 1
5 KIT232 Hose incl Clamp 1
6 CH12 Clamp 2
7 T19485924252 Vent Valve 15 1
9 T1A646024370 Magnet Holder 1
11 T19215427281 Spring 25 1
12 T1A646089510 Bypass Shaft B 1
13 T1A632029520 Bypass Lever 1
14 T19216829570 Ring 10 1
15 T1C655036300 Sealing Cap 30 1
16 T22252000350 Snap Ring C 35 1
21 T26476080552 Tapping Screw 8 * 55 1
22 T26476080302 Tapping Screw 8 * 30 1
23 T1A646024480 Tank Support 1
24 T1A646024910 Center Case K 1
25 T19216824760 Pin 3 * 9.8 1
26 T19216324950 Filter 1
27 T26106100752 Bolt 10 * 75 1
28 T1A646024800 Ids Valve 1
29 T1A646024761 Ids Spring 1
30 T1A646024790 Ids Filter 300 1
31 T19216825111 Cylinder Block Kit 1
32 T1A646025200 Spring 1
33 T1A646025251 Pump Shaft 1
35 T24101062020 Bearing 6202c3 1
36 T19216824210 Motor Housing 1
37 T19216324240 Thrust Bearing 51106 1
38 T19216825210 Cylinder Block Kit 1
39 T19216825230 Washer 12 * 24 * 1 1
40 T1A646025271 Motor Shaft 1
41 T19215425310 Snap Ring S15 1
42 T1A646085400 Motor Gear 12t 1
43 T24102062020 Bearing 6202 Duc3 1
44 T19216327060 Thrust Metal 1
45 T1A646024700 Swash Plate 1
49 T1A646029911 Control Shaft 1
50 T1A646029920 Fulcrum 1
51 T1A646029800 Torsion Spring, Standard 1
52 T1A646029900 Control Arm E 1
53 T1A646029851 Control Lever C 1
54 T1A646029350 Jerky Plate 1
55 T22137120000 Washer 12 1
56 T1A646029940 Cotter Pin 1/8" * 3/4" 1
57 T22351060036 Spring Pin 6 * 36 1
ITEM PART NO. DESCRIPTION QTY
67 T1A646033531 Final Pinion Gear (10t) 1
68 T1A646089430 Axle Shaft Left 1
69 T1A646089440 Axle Shaft Right 1
70 T19216334261 Thrust Washer 1
71 T19216834270 Ring 17 1
73 T19216834350 Bushing 1
75 T1A646036121 Brake Shoe 1
76 T1A646036160 Brake Lever 1
77 T1A646036171 Brake Shaft 1
78 T1A646036180 Brake Return Spring 1
79 T1A646036200 Brake Actuator 1
80 T22351050032 Pin 5 * 32 1
82 T22351040016 Spring Pin 4 * 16 1
86 T1A646083060 Wave Washer 1
89 T1A646024302 Upper Case Kit 1
90 T22351030020 Pin 3.0a * 20 1
95 T22351030016 Spring Pin 3.0a * 16 1
100 T26106080122 Drain Bolt 8 * 12 1
199 T1A646088150 Bearing 1
200 T1A646099140 K46 Seal Kit (All Models) 1
201 T46005 Repair Kit 1
58 T22351060040 Roll Pin 6 * 40 1
60 T26776120002 Nut 12 1
61 T1A646031510 Differential Gear Kit 1
62 T1A646033520 Final Gear (54t) 1
63 T1A646033250 Final Pinion Collar 1
64 T1A646033410 Reduction Shaft 1
65 T19216833420 Washer 12 * 32 * 3.2 1
66 T1A646083450 Reduction Gear 31t 1
Page 26
11 June 2015 Page 26 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Engine Ancillary Components B&S ONLY
Page 27
11 June 2015 Page 27 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Engine Ancillary Components B&S ONLY
ITEM PART NUMBER DESCRIPTION QTY
1 W051218 Washer, Flat 4
2 NM5NT Nut 2
3 BHSSM5X12 Screw, Control, Throttle 2
NM5NT Nut, Control, Throttle 2
4 A131101 Assy, Control, Throttle 1
5 Engine 1
A108109B09H Engine Plate 1
6 CHSS0512C Screw, Cap 2
7 Side muffler 1
8 Side muffler manifold 1
9 Gasket B&S 2
10 Side muffler deflector 1
11 ST0806 Screw 4
12 Side muffler screw 2
13 Side muffler bracket 1
14 WS050216 Washer, Lock, Spring 4
15 WS071008 Washer, Lock, Spring 1
16 80033 Tank, Fuel 1
17 CF01 Cap, Fuel 1
18 AM294 Grommet, Fuel Tap 1
19 AM293 Fuel Tap 1
20 14107 Fuel Hose 1
21 AM078B0 Mount, Plate 2
22 B0524C Bolt 4
23 A108103 Engine Pulley Spacer 2
24 GS0505C Screw, Set 1
KIT204 Engine Pulley Kit (incl pulley, spacer, key & screw) 1
25 A108104 Key, Engine Pulley 1
26 W072004 Washer, Flat 1
27 SH0724F Bolt 1
W071416 Washer, Flat 2
28 A105007B Bracket. Restrain, Fuel Tank 1
29 80037 Grommet 1
30 SPM5x12 Screw 2
AM295 Spark Plug Spanner 1
Page 28
11 June 2015 Page 28 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Engine Ancillary Components 13HP Honda ONLY
Page 29
11 June 2015 Page 29 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Engine Ancillary Components 13HP Honda ONLY
ITEM PART NUMBER DESCRIPTION QTY
1 80035 Sub-Assy, Tank, Fuel 1
1.1 CF01 Cap, Fuel 1
1.2 AM294 Grommet, Fuel Tap 1
1.3 AM293 Petrol Tap 1
1.4 14107 Line, Fuel, L=180 1
1.5 KIT167 Kit, Tank, Fuel 1
1.5.1 Tank, Fuel 1
1.5.2 Decal, Warning, Fuel 1
2 80037 Grommet 1
3 A107007B Bracket, Restrain, Fuel Tank 1
4 A107114Z Plate, Mount, Engine, 13.0 Hon, Left 1
5 A108101 Pulley, Engine 1
6 A108103 Spacer, Pulley, Engine, L=28 1
7 A108104 Key 1
8 A108109B09H Plate, Base, Engine 1
CP07 Clip 1
BHSSM5X12 Screw 1
NM5N Nut 1
9 AM078B0 Engine Mount Bolt Plate 1
10 B0524C Bolt 2
11 B0520F Bolt 2
12 SH0724F Bolt 1
W071416 Washer, Flat 2
13 SPM5X12 Screw, Pan 2
14 W051218 Washer, Flat 4
15 W072004 Washer, Flat 1
16 WS050216 Washer, Lock, Spring 4
17 WS071008 Washer, Lock, Spring 1
18 PR0306 Rivet 2
19 NCM5X2.5X9.5 Nut, Cage 2
20 A133033 Control, Speed, Engine, 13.0HP 1
Page 30
11 June 2015 Page 30 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Engine Ancillary Components 16HP HONDA ONLY
Page 31
11 June 2015 Page 31 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Engine Ancillary Components 16HP HONDA ONLY
ITEM PART NUMBER DESCRIPTION QTY
1 A119121C Pipe, Exhaust, Left 1
2 A119123C Pipe, Exhaust, Right 1
3 A119125Z Bracket, Muffler, 16.0 Hon 1
4 80033 Tank, Fuel 1
5 CF01 Cap, Fuel 1
6 80037 Grommet 1
7 A105007B Bracket, Restrain, Fuel Tank 1
8 90167 Muffler, Exhaust 1
9 80025 Deflector, Exhaust Gas 1
10 90168 Clamp, Hose, T-Bolt 4
11 AM294 Grommet 1
12 AM293 Petrol Tap 1
13 B0408TFS Screw 4
14 A119127B09G Baffle, Hot Air, Engine, Front 1
15 A119129 Fuel Line 1
16 SPM5X12 Screw, Pan 2
17 A116208Z Plate, Mounting, Engine, Right 1
18 A116207Z Plate, Mounting, Engine, Left 1
19 W05M202 Washer 4
20 A108101 Pulley, Engine 1
21 A108103 Spacer, Pulley, Engine 1
22 A108104 Key 1
23 WS071008 Washer, Lock, Spring 1
24 SH0724F Bolt 1
W071416 Washer, Flat 2
25 W072004 Washer 1
26 GS0505C Screw, Set 1
27 SH0850M Screw 4
28 NHCM8 Nut 4
A133133 Control, Speed, Engine 1
BHSSM5X12 Screw, Control, Throttle 2
NM5NT Nut, Control, Throttle 2
A119135 Clamp, Cable 1
NM8NT Nut 1
SH0616M Screw 1
W041216 Washer 1
AM295 Spark Plug Spanner 1
AM005G0 Spark Plug Spanner 16HP Honda Only 1
Page 32
11 June 2015 Page 32 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Page 33
11 June 2015 Page 33 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Electrical Components Schematic 16.5HP & 19.5HP B&S Only
ITEM PART NUMBER DESCRIPTION QTY
Engine, B&S 1
1 AM16512F Switch, Seat 1
1.1 SP1PNCSM Switch, Plunger 1
2 SKIT132 Switch, Plunger , Inc Cover 1
3 Battery, Automotive, 12V, CMFU1, 9PL, 240CCA 1
4 13125 Switch, Key 1
5 AM015 Pair, Key, Ignition 1
6 SH0616M Screw 2
7 AM159 Solenoid, Starter 1
NM6NT Nut 2
SH0620M Screw 2
8 SKIT133 Switch, Plunger, Inc Cover 1
9 NHM6 Nut 2
10 A143026 Harness, Wiring, Main 1
11 89082 Lead, Battery, Red, L= 295 1
12 AM265 Lead, Battery, Red, L= 490 1
13 15235 Lead, Battery, Black, 3term 1
14 N04C Nut 2
15 W040818 Washer 2
16 A143112 Harness, Wiring, Engine, B&S 1
17 Fuse, Glass, 3ag, 15 Amp 1
18 AM211 Hour Meter, Optional
Page 34
11 June 2015 Page 34 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Page 35
11 June 2015 Page 35 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Electrical Components Schematic 13HP HONDA Only
ITEM PART NUMBER DESCRIPTION QTY
Engine, Honda, 13.0 Hp
1 AM16512F Switch, Seat 1
1.1 SP1PNCSM Switch, Plunger 1
2 SKIT132 Switch, Plunger , Inc Cover 1
3 Battery, Automotive, 12V, CMFU1, 9PL, 240CCA 1
4 13125 Switch, Key 1
5 AM015 Pair, Key, Ignition 1
6 SH0620M Screw 2
7 AM159 Solenoid 1
NM6NT Nut 2
SH0616M Screw 2
8 SKIT133 Switch, Plunger , Inc Cover 1
9 NHM6 Nut 2
10 A143026 Harness, Wiring, Main 1
11 89082 Lead, Battery, Red, L= 295 1
12 AM265 Lead, Battery, Red, L= 490 1
13 15235 Lead, Battery, Black, 3term 1
14 N04C Nut 2
15 W040818 Washer 2
16 A143111 Harness, Wiring, Engine, Hon, 13.0 Hp 1
17 13149 Lead, Earth, Fuel Pump 1
18 Fuse, Glass, 3ag, 15 Amp 1
19 AM211 Hour Meter, Optional
Page 36
11 June 2015 Page 36 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Page 37
11 June 2015 Page 37 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Electrical Components Schematic 16HP HONDA Only
ITEM PART NUMBER DESCRIPTION QTY
Engine, 16.0hp, V2cyl, Elec, Hon, GXV530
1 AM16512F Switch, Seat 1
1.1 SP1PNCSM Switch, Plunger 1
2 A143026 Harness, Wiring, Main 1
3 13369 Lead, Battery, Black, 3term 1
4 13125 Switch, Key 1
5 Battery, Automotive, 12V, CMFU1, 9PL, 240CCA 1
6 Regulator/Rectifier, Honda 1
7 SKIT132 Switch, Plunger, Inc Cover 1
8 SKIT133 Switch, Plunger, Inc Cover 1
9 A143113 Harness, Wiring, Engine, Hon, 16.0 Hp 1
10 AM015 Pair, Key, Ignition 1
14 84132 Lead, Battery, Red 1
16 Fuse, Glass, 3 Ag, 15 Amp 1
17 NHM8 Nut 2
18 B0635M Bolt 2
19 NHM6 Nut 2
NM6NT Nut 2
20 SH0616M Screw 2
21 AM211 Hour Meter, Optional
Page 38
11 June 2015 Page 38 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Cutter Control Components
Page 39
11 June 2015 Page 39 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Cutter Control Components
ITEM PART NUMBER DESCRIPTION QTY
1 NM8NT Nut 4
2 NM6NT Nut 3
3 W05M202 Washer 3
4 A139104L Link, Drop, Disengagement, Cutter 1
5 AM369 Bush 2
6 KIT235 Kit, Link, Drag Inc Bushes 1
7 AM369 Bush 4
8 90022 Pin, Pivot 1
9 13016 Pin 2
10 90012 Connecting Link Adjuster Bracket 1
11 SH0825M Screw 2
12 SH0616M Screw 3
13 AM012 Height Adjustment Pawl Push Rod Spring 1
14 AM013Q2 Height Adjustment Pawl Push Rod Button 1
15 A108003Z Rod, Adjust, Height, Cut 1
16 W041216 Washer 1
17 RP04 Pin, 'R' 1
18 AM040 Spring, Extension 3
19 A139008Z Link, Adjust, Suspend, Front 1
20 & 21
A141010Z Link, Float, Suspend, Rear Mowing Attachment 32” & 38” 1
22 SH1025M Screw 2
23 W10MN Washer 2
24 NM10NT Nut 2
25 W10MN Washer 2
26 SH1030M Screw 1
27 NHCM10 Nut 2
28 W0620HD Washer 1
29 CP3-220 Pin, Split 1
30 B1040M Bolt 1
31 NFM10 Nut 1
32 NM8NT Nut 1
33 WSM10X3.7X2.5 Washer, Lock, Spring 1
34 AM009 Hand Grip 1
35 SH0825M Screw 1
36 W051218 Washer 1
37 A139020Z Link, Adjust, Disengagement 1
38 A139018Z Link, Disengagement 1
39 W10M Washer 3
40 A135105L Lever, Disengage, Cutter 1
41 RP01 Pin, 'R' 1
42 AM185BO Cutter Lifting Link 1
43 RP03 Pin, 'R' 1
44 NF06CN Nut 1
45 AM145 Spring, Extension, Weight Compensating 1
A118039 Spring, Extension, Wt Compensating, 38" Mowing Attachment 1
46 KIT235 Kit, Link, Drag, Attachment, Mowing, Inc Bushes 1
47 AM230 Bush - Plastic 4
Page 40
11 June 2015 Page 40 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
BEFORE & INCLUDING CR9606S s/n 2107, CR9607S s/n 10891, CR9610S s/n 600
32” Cutter Attachment & Components
Page 41
11 June 2015 Page 41 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
BEFORE & INCLUDING CR9606S s/n 2107, CR9607S s/n 10891, CR9610S s/n 600
32” Cutter Attachment & Components
Page 42
11 June 2015 Page 42 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
FROM CR9606S s/n 2108, CR9607S s/n 10892, CR9610S s/n 601
32” Cutter Attachment & Components
Page 43
11 June 2015 Page 43 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
FROM CR9606S s/n 2108, CR9607S s/n 10892, CR9610S s/n 601
32” Cutter Attachment & Components
ITEM PART NUMBER DESCRIPTION QTY
1 13016 Pin 1
2 251301 Rod, Adj, Cutter Brake 387mm 32"Cut 1
3 A100010 Lever, Brake, Cutter, Lawnboss 1
4 Arm, Lever, Brake, Cutter, Lawnboss 1
5 AM033I95 Pad, Brake, Cutter 1
6 PR0205 Rivet 2
7 AM034H0 Cutter Head Brake Adj Brkt 1
8 AM035 Spring, Compression, Cutter Brake 1
9 AM07604A Disc, Cutter 1
10 AM259 Deflector, Cox Logo 1
11 B0620C Bolt 4
12 KIT199 Kit, Housing, Cutter, 805(32") 1
13 Deck, Cutter, 805(32"),Lawnboss 1
14 A100030L Guard, Cutter, 805(32") 1
15 A100003 Spring, Torsion, Deflector 1
16 AM274 Fastener, Pushon, Round, 1/4" 1
17 BCHSNM8X20 Bolt, Cup, Sq Neck 3
18 NM8NT Nut 2
19 DEC116 Decal, Danger, Mowing Attachment 2
20 W051218 Washer 2
21 KIT253 Kit, Head, 25, Cutter, 805(32"),Lawnboss 1
22 A100050Z Spacer, Sleeve 1
23 A100052 Key 1
24 A100056 Pulley,Cutter, Ci 1
25 A100062 Kit, Sub-Assy, Spindle, Flanged, 25, Lawnboss 1
26 Spindle, Flanged, Cutter 1
27 A100060Z Washer 1
28 BB305513NS Bearing, Ball 1
29 WSM10X3.66X2.69 Washer, Lock, Spring 1
30 SH1030M10.9 Screw 1
31 WW0616 Washer, Wave 1
32 W10MN Washer 1
33 A100064 Sub-Assy, Housing, Bearing, Cutter 1
34 Housing, Bearing 1
35 A100013Z Guide,Belt,Cutter 2
36 A100027Z Brace,Guide,Belt 2
37 B0635M Bolt 2
38 NM6N Nut 2
39 BB255215NN Bearing,Ball 1
40 W103506 Washer 1
41 N06CN Nut 4
42 NF06CN Nut 4
43 NM8NT Nut 3
44 NS05C Nut, Sqr 1
45 SH0612C Screw 4
46 SH0820M Screw 2
47 SKIT54N Pair, Blade+Bolt+Washer+Nut 1
48 SKIT01D1 Blade Bolt & Nut Set 1
49 Nut 2
50 Washer, Wave 2
51 Blade Bolt Grade 8 2
52 Blade, Mower, Swingback, Standard, 198 2
53 W051218 Washer 2
54 RP01 Pin, 'R' 1
55 NM6NT Nut 1
56 SH0616M Screw 1
57 V13 Belt,V 1
Page 44
11 June 2015 Page 44 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
960mm 38” Cutter Attachment Components
Page 45
11 June 2015 Page 45 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
960mm 38” Cutter Attachment Components
ITEM PART NUMBER DESCRIPTION QTY
1 NM10NT Nut 12
2 NCM8X4.75 Nut, Cage 2
3 A152043Z Axle, Tensioner 1
4 AM017C1 Steering Shaft Bush With Collar 1
5 14025 Boss, Idler 1
6 WS050216 Washer, Lock, Spring 1
7 SH0825M Screw 1
8 PIFBB03 Idler, Flat 1
9 A152017Z Arm, Tensioner, Belt 1
10 B1090M Bolt 1
11 V59 Belt, V 1
12 A152153L Guard, Pulley, Left 1
13 A152155L Guard, Pulley, Right 1
14 NCM6X1.6X9.5 Nut, Cage 4
16 NM8NT Nut 4
17 SH0825M Screw 2
18 A152172 Arm, Brake, Cutter, 38", Lawnboss 1
18.2 AM033I95 Pad, Brake, Cutter 1
18.3 PR0205 Rivet 2
19 SH0820M Screw 4
20 WS050216 Washer 2
21 W08MN Washer 2
22 WS040816 Washer, Lock, Spring 4
23 W06MN Washer 4
24 SH0620M Screw 6
25 AM073 Belt Guides 2
26 NM6NT Nut 3
27 AM264 Spring 1
28 A152062 Wheel 3
29 AM25703H Wheel 1
30 AM258 Flotation Wheel Bush 1
31 B0648C Bolt 1
32 N14MN Nut 3
33 NHM14 Nut 3
34 B1480M Bolt 3
35 W092016 Washer 12
36 AM259 Deflector 1
37 A100003 Spring, Torsion, Deflector 1
38 AM274 Fastener, Pushon 1
39 AM034H0 Cutter Head Brake Adj Brkt 1
40 AM035 Spring, Compression, Cutter Brake 1
41 13317 Rod, Adjust, Brake, Cutter 1
42 NS05C Nut, Sqr 1
43 N06CN Nut 1
44 W10M Washer 1
45 13016 Pin 1
46 SH0616M Screw 1
47 V61 Belt, V 1
48 W051218 Washer 1
49 RP01 Pin, 'R' 1
50 KIT242 Deck, Mower, Side, 960(38"), Fab, Bk, +Decals 1
50.1 DEC116 Decal, Danger, Mowing Attachment 2
Page 46
11 June 2015 Page 46 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
960mm 38” Cutter Attachment Spindle Components
Page 47
11 June 2015 Page 47 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
960mm 38” Cutter Attachment Spindle Components
ITEM PART NUMBER DESCRIPTION QTY
1 A152103L Frame, Reinforce 1
2 A152005B Housing, Bearing, Flange, Short 2
3 BB205215NS Bearing, Ball 2
4 A15202012K Kit, Spindle, Flanged, Cutter 2
5 A118012Z Shield, Bearing 2
6 BB255215NN Bearing, Ball 2
7 A152011B Spacer, Disc, Cutter 2
8 A152013B Disc, Cutter 2
9 BHSSM10X30 Screw, Button 8
10 NM10NT Nut 8
11 SKIT41N Pair, Blade+Bolt+Washer+Nut, Airflow 2
12 SKIT01D1 Blade Bolt & Nut Set 2
13 Nut 1
14 Washer, Wave 1
15 Blade Bolt Grade 8 1
16 SMB137A Pair, Blade, Mower, Swingback, Airflow 1
17 SH1030M Screw 12
18 NM10NT Nut 11
19 A118003 Pulley, Cutter, CI 2
20 A100025 Key 2
21 WSM10X3.7X2.5 Washer, Lock Spring 2
22 SH1030M10.9 Bolt 2
23 9801611M Flange 1
24 A152183 Sleeve, Spacer, Bearing 1
25 BB255215NN Bearing, Ball 2
26 A152181 Pulley, Transfer 1
27 W103506 Washer 1
28 WS103.52.2 Washer, Lock, Spring 1
29 A152115L Axle, Flanged 1
Page 48
11 June 2015 Page 48 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
DECALS
ITEM PART NUMBER DESCRIPTION QTY
1 13094 Pad, Non-Skid, Running Board 2
2 DEC08505K Decal, Warning, Fuel 1
3 8906608A Non-Skid, Pedal, Drive 1
4 95067 Non-Slip, Brake Pedal 1
5 DEC116 Decal, Danger, Mowing Attachment 2
6 DEC269 Decal, Lawn Boss, Proudly Australian 1
7 DEC270 Decal, Lawn Boss Bonnet 2
8 DEC124 Decal, Brake 1
9 DEC125 Cutter Disengage 1
10 DEC127 Mount This Side Only 1
11 DEC135 Decal, Caution, Hot Muffler 1
12 DEC136 Decal, Drive Pedal 1
13 DEC248 Decal, Lawn Boss, Console Top 1
14 DEC275 Decal, Lawn Boss, Dash 1
15 DEC271 Decal, Lawn Boss, 13 Hp 2
DEC272 Decal, Lawn Boss, 16 Hp 2
DEC273 Decal, Lawn Boss, 16.5 Hp 2
DEC274 Decal, Lawn Boss, 18.5 Hp 2
DEC296 Decal, Lawn Boss, 19.5 Hp 2
16 DEC199 Decal, Guard Infill, Lawn Boss L/H 1
17 DEC200 Decal, Guard Infill, Lawn Boss R/H 1
18 DEC224 Decal, Park Brake, Lawn Boss 1
DEC299 Decal, Oil Transaxle 1
Page 49
11 June 2015 Page 49 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Page 50
70 Landseer Street
Acacia Ridge Qld 4110
Australia
PH 07 3323 2222 FAX 07 3344 6233
Web Site Address: www.coxmowers.com.au
Email: sales@coxmowers.com.au
Loading...