Coulisse CM18 User Manual

MANUAL CM-18

Pull remote 1 channel

English

CM-18 is a pull remote with 1 channel for operating single blinds or
shading networks with a simple pull. Blinds can be moved to any desired
position. Pull once to move the blinds to the end positions, pull again to
stop the blinds. Operating remotely controlled blinds has never been so
easy and intuitive: anyone can do it.

Max.

Fre-

Channels

blinds

1 Unlim ited

quency

433.925
MHz

Range Frequency

20 m
open
space

Power
emission
power

≤2.32dBm

Length Width Height Working

supply

2 x

19.5

LR44

mm ø

1.5V

For the latest information and updated manuals,
visit rtube.nl/cm-18

69.9
mm

temperature

-10°C~50°C

Certificates

Safety

WARNING: Important safety instructions.

Follow all instructions, since incorrect
installation can lead to severe injury.

Do not let children play with the blind

and/or remote control.

Take care that the blind can move

freely and is not blocked by any

objects.
Do not paint the device.
Keep the device dry.
Do not drop, knock, or shake the

device. Rough handling can break

internal circuit boards.
Do not ingest battery, Chemical Burn

Hazard" or equivalent wording

This product contains a coin / button

cell battery. If the coin / button cell
battery is swallowed, it can cause
severe internal burns in just 2 hours
and can lead to death.

Keep new and used batteries

away from children.If the battery
compartment does not close securely,
stop using the product and keep
it away from children. If you think
batteries might have been swallowed
or placed inside any part of the body,
seek immediate medical attention.

Replacement of a battery with an

incorrect type that can defeat a
safeguard.

Disposal of a battery into fire or a

hot oven, or mechanically crushing or
cutting of a battery, that can result in
an explosion.

Leaving a battery in an extremely high

temperature surrounding environment
that can result in an explosion or the
leakage of flammable liquid or gas.

A battery subjected to extremely low

air pressure that may result in an
explosion or the leakage of flammable
liquid or gas.

Cleaning

Follow these general rules when cleaning the
outside of the device and its components:

Use a damp, soft, lint-free cloth. Avoid

getting moisture in openings.

Do not use aerosol sprays, solvents,

alcohol, or abrasives.

Service & Support

Do not perform repairs yourself. Do
not attempt to open the device or
disassemble it. You run the risk of electric
shock and voiding the limited warranty.
No user-serviceable parts are inside.

Warranty Service

First follow the advice in this manual. If
the product appears to be damaged or
does not function properly, go to your

local dealer for instructions on how to
obtain warranty service.

Recycle

This marking indicates that
this product should not be
disposed with other household

wastes throughout the
EU. To prevent possible harm to the
environment or human health from
uncontrolled waste disposal, recycle it
responsibly to promote the sustainable
reuse of material resources. To return
your used device, please use the return
and collec-tion systems or contact

the retailer where the product was
purchased. They can take this product for
environmental safe recycling.

EU Declaration

Hereby, Coulisse declares that the radio
equipment type CM-18 is in compliance
whith directive 2014/53/EU. The full
text of the EU declaration of conformity
is available at the following internet
address: www.my.coulisse.com

FCC Manual I FCC ID: ZY4CM18

Regulatory Information

1 FCC Information for User

This product does not contain any user-serviceable
components and is to be used with approved antennas
only. Any product changes or modifications will
invalidate all applicable regulatory certifications and
approvals.

2 FCC Electronic Emission Notices

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received,
including interference that may cause undesired
operation.

3 FCC Radio Frequency Interference
Statement

This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio-frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.

Operation of this equipment in a residential area may
cause harmful interference, in which case the user will
be required to correct the interference at their own
expense.

If this equipment does cause harmful interference to
radio or television reception, which can be determined

by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:

Reorient or relocate the receiving antenna
Increase the distance separating the equipment and

receiver

Connect the equipment to an outlet on a circuit

different from that to which the receiver is connected

Consult the dealer or an experienced radio/TV

technician for help

1 2

Buttons

Pair

Button

1. BUTTONS 2. CHANGING THE BATTERY

Changing the battery

1

+

-

LR44 1.5V

2

3

Pair a remote

Repeat steps 3.1 - 3.2 to remove a blind
from a channel.

3. PAIR A REMOTE 3. PAIR A REMOTE

Shortly press the program button on the motor. The

3.1

blind will start stepping, indicating that program mode
has been activated.
(The blind remains stepping until the program mode is
de-activated.)

Press the pair button on the remote control to pair the

3.2

blind to the remote control. The blind will shortly stop
stepping indicating that the remote has been paired to
the blind.

Pair

button

4

Connect a chain

3

1

2

4. CONNECT A CHAIN 4. CONNECT A CHAIN

4

5

5

Attach to a blind

Roller blind bracket Roller blind cassette

RCU-21

drill a ø 5 mm hole

5. ATTACH TO A BLIND

5. ATTACH TO A BLIND

Roman blind Venetian blind

drill a ø 5 mm hole

drill a ø 5 mm hole

5. ATTACH TO A BLIND 5. ATTACH TO A BLIND

6

Control

After the blind has reached its end position, the
consecutive ”STOP” command is eliminated after
60 seconds. The next pull will directly operate the blind.

6. CONTROL

Pull once to move the

6.1 6.2 6.3

blind to its end position.

Pull again to stop the
blind.

6. CONTROL

Pull again to move the blind
in the opposite direction.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form, by any means, electronic, mechanical, photocopying,
recording, digital or otherwise without the written permission of the publisher.
Although this manual has been composed with the utmost care, Coulisse b.v. does not
accept any responsibility for damage due to mistakes and/or faults in this manual.
Coulisse b.v. reserves the right to revise the manual and to revise and/or change its
content at any time, without obligation to notify any person or entity of such revisions
or changes.

motion-blinds.com

CM18U-R3