Page 1
MANUAL
CM-15
Wall remote 1 channel
English
Page 2
CM-15 is a wall remote with 1 channel for operating and programming
blinds at the push of a button. Blinds can be moved to any desired position
or to a preset favourite position. The remote control can be used separately
from the wall plate as as a hand-held remote separately.
Channels Max.
15 Unlimited
Frequency Range Frequency
blinds
433.925
MHz
30 m with
1 concrete
wall
Power
emission
power
≤2.32dBm
Length Width Height Working
supply
CR2430
120 mm 45 mm 14 mm -10°C~50°C
3.0V
For the latest information and updated manuals,
visit rtube.nl/cm-15
temperature
Certificates
Safety
WARNING: Important safety instructions.
Follow all instructions, since incorrect
installation can lead to severe injury.
Do not let children play with the blind
and/or remote control.
Take care that the blind can move
freely and is not blocked by any objects.
Do not paint the device.
Keep the device dry.
Do not drop, knock, or shake the device.
Rough handling can break internal
circuit boards.
Do not ingest battery, Chemical Burn
Hazard" or equivalent wording
This product contains a coin / button
cell battery. If the coin / button cell
battery is swallowed, it can cause
severe internal burns in just 2 hours
and can lead to death.
Keep new and used batteries
away from children.If the battery
compartment does not close securely,
stop using the product and keep
it away from children. If you think
batteries might have been swallowed
or placed inside any part of the body,
seek immediate medical attention.
Replacement of a battery with an
incorrect type that can defeat a
safeguard.
Page 3
Disposal of a battery into fire or a
hot oven, or mechanically crushing or
cutting of a battery, that can result in
an explosion.
Leaving a battery in an extremely high
temperature surrounding environment
that can result in an explosion or the
leakage of flammable liquid or gas.
A battery subjected to extremely low
air pressure that may result in an
explosion or the leakage of flammable
liquid or gas.
Cleaning
Follow these general rules when
cleaning the outside of the device and its
components:
Use a damp, soft, lint-free cloth. Avoid
getting moisture in openings.
Do not use aerosol sprays, solvents,
alcohol, or abrasives.
Service & Support
Do not perform repairs yourself. Do
not attempt to open the device or
disassemble it. You run the risk of electric
shock and voiding the limited warranty.
No user-serviceable parts are inside.
Warranty Service
First follow the advice in this manual. If
the product appears to be damaged or
does not function properly, go to your
local dealer for instructions on how to
obtain warranty service.
Recycle
This marking indicates that this
product should not be disposed
with other household wastes
throughout the EU. To prevent possible
harm to the environment or human
health from uncontrolled waste disposal,
recycle it responsibly to promote the
sustainable reuse of material resources.
To return your used device, please use the
return and collec-tion systems or contact
the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
EU Declaration
Hereby, Coulisse declares that the radio
equipment type CM-15 is in compliance
whith directive 2014/53/EU. The full
text of the EU declaration of conformity
is available at the following internet
address: www.my.coulisse.com
Page 4
FCC Manual I FCC ID: ZY4CM15
Regulatory Information
1 FCC Information for User
This product does not contain any user-serviceable
components and is to be used with approved antennas
only. Any product changes or modifications will
invalidate all applicable regulatory certifications and
approvals.
2 FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received,
including interference that may cause undesired
operation.
3 FCC Radio Frequency Interference
Statement
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio-frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area may
cause harmful interference, in which case the user will
be required to correct the interference at their own
expense.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance separating the equipment and
receiver
Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV
technician for help
Page 5
1 2
Buttons Activate the remote
Left
Down
The center button has two functions:
press to stop the blind, hold to move
the blind to its favorite position.
Indicator
Up
Centre
(stop/favourite)
Right
1. BUTTONS 2. ACTIVATE THE REMOTE
Pair
button
Page 6
3
Changing the battery
1
When the indicator is flashing at a high
frequency, the battery needs to be
replaced.
2
+
-
CR2430 3,0V
3. CHANGING THE BATTERY 3. CHANGING THE BATTERY
3
Click!
Click!
Page 7
4
Remote holder
Different materials require
different types of fittings.
Always choose screws
and plugs that are specially
suited to the material.
PICO-WBX-ADAPT
(ABC-27)
Claro wallplate
(ABC-27)
4. REMOTE HOLDER 4. REMOTE HOLDER
Claro wallplate
(ABC-27)
Page 8
5
Pair a remote
Repeat steps 5.1 - 5.2 to remove a blind
from a channel.
5. PAIR A REMOTE 5. PAIR A REMOTE
Shortly press the program button on the motor. The
5.1
blind will start stepping, indicating that program mode
has been activated.
(The blind keeps stepping until the program mode is
deactivated)
Press the pair button on the back of the remote control
5.2
to pair the blind with the remote control.
The blind will shortly stop stepping, indicating that the
remote has been paired with the blind.
Pair
button
Page 9
of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form, by any means, electronic, mechanical, photocopying, recording, digital or otherwise
without the written permission of the publisher.
Although this manual has been composed with the utmost care, Coulisse b.v. does not
accept any responsibility for damage due to mistakes and/or faults in this manual.
Coulisse b.v. reserves the right to revise the manual and to revise and/or change its
content at any time, without obligation to notify any person or entity of such revisions
or changes.
motion-blinds.com
CM15U-R3
Loading...