Page 1
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
CM-15
1 Channel Wall Remote
Left
Down
Up
Centre (stop/
favourite)
Right
CM-16
4 Channel Wall Remote
Up
Down
Centre (stop/
favourite)
1 Channel Tassel Remote
CM-18
CM-20
Motion Bridge
English
Pair
Button
Pair
Button
Pair
Button
See manual CM-20
Page 2
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
1 5
Install the blind
2
Click!
2.1
2.32.2
Click!
3
Pair a remote
Pair a remote control that is able to program blinds. See pages 4 and 5
for remote controls details. In this manual CM-12 is displayed.
Shortly press the program button on the
5.1
motor. The blind will start stepping, indicating
that program mode has been activated.
(The blind remains stepping until the program
mode is de-activated.)
Select a desired channel for the blind using the
5.2
channel selection button on the remote control.
Press the pair button on the back of the remote
5.3
control to pair the blind to the selected channel.
The blind will shortly stop stepping indicating
that the remote has been paired to the blind.
Repeat steps 5.1 - 5.3 to remove a blind from
a channel.
Channel
Selection
Channel
Indicator
Button
Pair
English
English
Activate the motor
4
Activate the motor by charging it with a micro
USB cable. A green LED will start flashing.
The motor can be used during charging.
(To activate the motor without a micro
USB cable see step 24)
End limits must be programmed to use a blind properly and to prevent it from being damaged.
Proceed to step 11 if end limits are already set.
6
Check direction of rotation
WARNING: risk of damage.
Stop the blind before reaching
the end positions.
Up
Down
Shortly press the down button to check if the
6.1
blind unrolls the right way. If the blind moves
up, the direction of rotation must be changed.
Simultaneously press the up and down button
6.2
to change the direction of rotation.
Page 3
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
7
Set bottom position
Down
Press and hold the down button until the
7.1
blind reaches the desired bottom position.
WARNING: Risk of damage.
Slowly approach the bottom position.
9
Set top position
Up
Press and hold the up button until the blind
9.1
reaches the desired top position.
WARNING: Risk of damage.
Slowly approach the top position.
English
8 10
Simultaneously hold the centre and the up
8.1
Centre
Up
button until the blind stops stepping and
starts stepping again.
The bottom position has been saved.
Centre
Down
Simultaneously hold the centre and the down
10.1
button until the blind stops stepping and
starts stepping again.
The top position has been saved.
Page 4
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
11
Set favourite position (optional)
Centre
Move the blind to a desired favourite position.
11.1
Hold the centre button to save this favourite
11.2
position. The blind shortly stops stepping,
indicating the favourite position has been
saved.
13
Operate the blind
Centre
Channel
Selection
Pull control: Pull once to move the blind to the
end positions. Pull again to stop the blind.
Up
Down
Remote control: Choose the channel to which the blind
has been paired using the channel button.
Press the up or down button to operate the blind.
Press the centre button to stop the blind.
English
12
De-activate program mode
Shortly press the program button to de-activate
12.1
program mode. The blind stops stepping and can
be operated.
14
Operate to favourite position
Centre
Pull control: Pull and hold to move the blind to
the favourite position.
Remote control: Press the centre button to
move the blind to the favourite position.
Page 5
MOTION CM-08 LI-ION END MOTOR MOTION CM-08 LI-ION END MOTOR
15
Reset favourite position
15.1
Move the blind to a desired favourite position.
Press the program button on the motor to activate
Centre
15.2
program mode. The blind starts stepping.
Hold the centre button to save this favourite position. The blind shortly
15.3
stops stepping indicating the favourite position has been saved succesfully.
Press the program button on the motor to de-activate
15.4
program mode. The blind stops stepping.
De-activate direct control Recharge the battery
When pressing the up or down button on the remote control the blind directly moves to
its end positions (direct control). To operate the blind with smaller steps using the up and
down button, direct control can be de-activated. Now, the blind only directly moves to its end
positons when the up or down button is held longer than two seconds.
17
Reset the blind
It is possible to only delete end limits or to do a factory reset.
Factory reset will delete the end limits and remove the connection to any paired remote.
17.1
Press the program button on the motor to activate program mode.
Delete end limits: To delete the end limits of the blind hold the program button
until the blind stops stepping for the first time, keep holding the button until the
blind stops stepping for the second time. (approximately 10 seconds)
Factory reset: To reset the blind to factory defaults hold the button for at least 20 seconds.The blind will
stop stepping twice. After the second stop the blind will give one extra step to confirm factory reset.
1816
A fully discharged CM-08 will need approximately
12 hours to recharge.
English
Use a micro USB cable
to charge the motor.
Press the program button on the motor to activate
16.1
program mode. The blind starts stepping.
Hold the program button until the blind stops stepping (approximately 5 seconds)
16.2
to de-activate or re-activate direct control.
LED light flashes
red during operation;
charge the battery.
LED light flashes
green;
battery is charging.
LED light constantly
green;
battery is fully charged.
Loading...