Coulisse CM05 User Manual

MOTION CM-05 LI-ION TUBULAR MOTOR MOTION CM-05 LI-ION TUBULAR MOTOR

8

Set bottom position

Down

Press and hold the down button until the

8.1

blind reaches the desired bottom position.

WARNING: risk of damage.

Slowly approach the bottom position.

10

Set top position

Up

Press and hold the up button until the blind

10.1

reaches the desired top position.

WARNING: risk of damage.

Slowly approach the top position.

English

9 11

Simultaneously hold the centre and the up

9.1

Centre

Up

button until the blind stops stepping and
starts stepping again.
The bottom position has been saved.

Centre

Down

Simultaneously hold the centre and the down

11.1

button until the blind stops stepping and
starts stepping again.

The top position has been saved.

MOTION CM-05 LI-ION TUBULAR MOTOR MOTION CM-05 LI-ION TUBULAR MOTOR

12

Set favourite position (optional)

Centre

Move the blind to a desired favourite position.

12.1

Hold the centre button to save this Favourite

12.2

position. The blind shortly stops stepping
indicating the favourite position has been
saved.

14

Operate the blind

Centre

Channel

Selection

Pull control: pull once to move the blind to the
end positions. Pull again to stop the blind.

Up

Down

Remote control: Choose the channel with which the
blind has been paired using the channel button.
Press the up or down button to operate the blind.
Press the centre button to stop the blind.

English

13

Deactivate program mode

Shortly press the program button to deactivate

13.1

program mode. The blind stops stepping and can
be operated.

15

Move to favourite position

Centre

Pull control: Pull and hold to move the blind to
the favourite position.

Remote control: press the centre button to move
the blind to the favourite position.

MOTION CM-05 LI-ION TUBULAR MOTOR MOTION CM-05 LI-ION TUBULAR MOTOR

16

Reset favourite position

16.1

Move the blind to a desired favourite position.

Press the program button on the motor to activate

Centre

16.2

program mode. The blind starts stepping.

Hold the centre button to save this favourite position. The blind shortly

16.3

stops stepping, indicating the favourite position has been saved succesfully.

Press the program button on the motor to deactivate

16.4

program mode. The blind stops stepping.

Deactivate direct control Recharge the battery

When pressing the up or down button on the remote control, the blind directly moves to
its end positions (direct control). To operate the blind with smaller steps using the up and
down button, direct control can be deactivated. Now, the blind only directly moves to its end
positions when the up or down button is held longer than two seconds.

18

Reset the blind

It is possible to only delete end limits or to do a factory reset.
Factory reset will delete the end limits and remove the connection to any paired remote.

18.1

Press the program button on the motor to activate program mode.

Delete end limits: to delete the end limits of the blind, hold the program button
until the blind stops stepping for the first time, and keep holding the button until
the blind stops stepping for the second time. (approximately 10 seconds)

Factory reset: to reset the blind to factory defaults hold the button for at least 20 seconds. The blind will
stop stepping twice. After the second stop the blind will give one extra step to confirm factory reset.

1917

A fully discharged CM-05 will need approximately
12 hours to recharge.

English

Use a micro USB cable

to charge the motor

Press the program button on the motor to activate

17.1

program mode. The blind starts stepping.

Hold the program button until the blind stops stepping (approximately 5 seconds)

17.2

to deactivate or reactivate direct control.

LED light flashes

red during operation;

Charge the battery

LED light flashes

green;

battery is charging

LED light constantly

green;

battery is fully charged

1

11

MOTION CM-05 LI-ION TUBULAR MOTOR MOTION CM-05 LI-ION TUBULAR MOTOR

Advanced options

20

Manual control

In case there is no remote control or pull control, the blind can
be operated with the program button on the motor.

Hold the program button to manually operate

20.1

the blind. The blind will move as long as the
button is being pressed. (max. 15 sec.)

To move the blind in opposite direction, release

20.2

the program button and repeat step 20.1.

Single select 5 channel remote

21

Single select makes it possible to activate program mode on a single blind through a
remote control, without having to physically press the program button on the blind.

Single select 15 channel remote

22

Single select makes it possible to activate program mode on a single blind through a
remote control, without having to physically press the program button on the blind.

To activate Single

22.1

select, simultaneously
hold the centre
button and press the
pair button.

Once a blind is found,

22.3

the channel number
will flash and the
blind starts stepping,
indicating that
program mode has
been activated. The
blind can now be (un)
paired to the remote
and/or programmed.

1

1

22.2

+

To search for

22.4 22.5

the next blind,
press the right
button. Search
mode will be
activated.
To find the
previous blind,
press the left
button.

The remote starts
searching for blinds
(search mode). This
is indicated by the
horizontal bars on the
remote.

To exit Single
select, press
the right
button during
search mode.
The display
shows the
letter O.

English

To activate

21.1 21.2

Single select,
simultaneously
hold the centre
button and press
the pair button.

Once a blind is found,
the channel LED will
flash and the blind starts
stepping, indicating that
program mode has been
activated. The blind
can now be (un)paired
to the remote and/or
programmed.

+

To search for

21.4 21.521.3

the next blind,
press the right
button. Search
mode will be
activated.
To find the
previous blind,
press the left
button.

The remote starts searching
for blinds (search mode).
This is indicated by the LEDs
flashing from left to right.

To exit
Single select,
press the
right button
during
search
mode.

1

3 3 3

3 3 3

3 3 3

3 3

MOTION CM-05 LI-ION TUBULAR MOTOR MOTION CM-05 LI-ION TUBULAR MOTOR

23

Channel select 5 channel remote

Channel select makes it possible to copy blinds in between channels/remotes without having
to physically press the program button on the motors.

Select the channel

23.1 23.2

from which the
blinds must be
copied.

To activate
channel select,
simultaneously
hold the channel
selection button
and press the pair
button.

Activate / deactivate the motor

25

To prevent the blind from getting damaged, the motor has a transport
mode that makes sure the blind will not be activated before installation.

Hold the program button and pull twice to activate or deactivate the motor.

25.1

The motor can also be activated by charging it with a micro USB cable.

+

+

or

All blinds in the selected

23.3

channel will start
stepping, indicating
program mode has been
activated. All blinds
can be copied to a new
channel on the same
remote or a different
remote. Select a new
channel on the (new)
remote.

24

Channel select 15 channel remote

Channel select makes it possible to copy blinds in between channels/remotes without having
to physically press the program button on the motors.

Select the channel

24.1

you would like to
copy.

All blinds in the selected

24.3 24.4

channel will start
stepping, indicating
program mode has been
activated. All blinds
can be copied to a new
channel on the same
remote or to different
remotes. Select a channel
on a (new) remote.

1

3

Press the pair

23.4 23.5

button on the (new)
remote to pair the
blinds with the new
channel.

To activate

24.2

channel select,
simultaneously hold
the channel selection
button and press the
pair button.

Press program
button on the (new)
remote to pair the
blinds with the
(new) remote.

1

To exit channel
select, go back to the
channel selected at
step 23.1 and repeat
step 23.2

+

To exit channel

24.5

select, choose
the channel you
selected at step 24.1
and repeat step 24.2

Frequently Asked Questions

Problem Cause Solution

Motor is in transport mode. Activate the motor. See step 25.

Motor battery is empty. Charge the motor. See step 19.

Remote battery is empty. (LEDS of
remote are flashing rapidly.)

Remote battery is inserted

Blind does not work.

Motor LED flashes red. The battery of the motor is empty. Charge the motor. See step 19.

Blind is not charging. Charger is not plugged in or does

Multiple blinds respond to a
remote. (Unable to program
a single blind)

Blind moves in small steps.

Favourite position can not
be programmed.

Blind lowers too far.

Blind moves in the opposite
direction.

The blind keeps moving up
and down.

incorrectly.

Radio-frequency interference Make sure that the antenna of the motor

The distance from the remote to
the motor is too far.

The remote is not connected to
the blind.

not work.

Multiple blinds are paired with a
single channel.

1) No end limits are programmed.

2) Direct control is deactivated.

No end limits are programmed. Program end limits.

End limits are programmed
incorrectly.
The rotational direction has been
set incorrectly.

The blind is in program mode.

Replace the battery in the remote.
See the manual of the remote.

Replace the battery in the remote.
See the manual of the remote.

is out of the way of metal objects.

Move closer to the motor.

Pair the remote with the motor.
See step 6.

Try a different charger or make sure the
charger is plugged in the outlet.

Pair the blind with a free channel to
program or use single select to program
the blind.

1) Program end limits. See step 8 - 11.

2) Activate direct control. See step 17.

See step 8 - 11.

Reprogram end limits. See step 8 - 11.

Change the rotational direction.
See step 7.

Press the program button on the motor
to exit program mode.

English

MOTION CM-05 LI-ION TUBULAR MOTOR MOTION CM-05 LI-ION TUBULAR MOTOR

Disclaimer:

© Copyright Coulisse

All rights reserved. No part of this publication may be reproduced,

stored in a retrieval system, or transmitted, in any form, by any

means, electronic, mechanical, photocopying, recording, digital or

otherwise without the written permission of the publisher.

For the latest information and updated

manuals, visit rtube.nl/cm-05

Although this manual has been composed with the utmost

care, Coulisse B.V. does not accept any responsibility for damage

due to mistakes and/or faults in this manual.

Coulisse B.V. reserves the right to revise the manual and to revise

and/or change its content at any time, without obligation to

notify any person or entity of such revisions or changes.

The most recent version replaces older versions of this manual.

The most recent version is available at my.coulisse.com or by

contacting your Coulisse contact person.

We invite you to send remarks and comments about this manual

to Coulisse at [e-mail].

English

Coulisse B.V. Vonderweg 48 7468 DC Enter The Netherlands

t [phone] f [phone] e [e-mail]

coulisse.com

CM05-U-R2