Cotell Fuego1000 SmartStation FG1066-IP (1S) SP User Manual

FG1066-IP(1S)SP

Hospitality Telephones

User Guide

Fuego1000™ SmartStation™

Trimline IP Telephone

FG1066-IP (1S) SP

FG1066-IP(1S)SP

FG1066-IP(1S)SP Face Drawing

Features

 Support one/two SIP account(s)
 Support SIP V2 (RFC3261) protocol
 Support RFC2833 (RTP Payload for DTMF

Digits, in band/out band DTMF)

 Support RFC3264 / 3489 / 3515 (Refer) /

2327 (SDP) / 3581 / 3265 (event
notification) / 3842 (MWI)

 Support RTP / NTP / DHCP / TFTP / HTTP

protocols

 STUN, DNS, PPPoE, static IP and DHCP
 Refresh DHCP upon network reconnection
 Proxy address and registrar address

configurable

 Local SIP port and registrar port

configurable

 Registration expiry configurable
 Audio codec supported: G.711a/u, G.722,

G.726, G.729, iLBC

 CNG and VAD supported
 Call hold, call waiting, call flash
 Last number redial
 Voicemail notification (MWI)
 volume up/down, mute
 Call log on Web Portal
 f/w upgrade on Web Portal
 Web Portal login / password configurable
 configuration backup and restore on Web

Portal

 Emergency Call triggered by off-hook

FG1066-IP(1S)SP

Installation

1. Unpack the box and check for the following items:
a. Main telephone body c/w base unit
b. Handset
c. Handset cord
d. RJ45 Line cord

2. Connect the handset to the base unit using the coiled handset cord provided

3. Connect one end of the line cord to the RJ45 socket at the base unit, and the other end
to the wall Ethernet outlet

4. Install the faceplate (if delivered separately) onto the telephone

Call Operation

A. Initiating a Call

1. Lift the handset.

2. Listen to dial tone.

3. Press the desired number on the keypad and wait for 5 second or press “#” to dial out.

4. To end the call, place the handset back on the cradle in the base unit.

B. Answering a Call

An audible ringing sound and the flashing LED indicates the incoming call.

1. Lift up the handset to answer the call.

2. To end the call, place the handset back on the cradle. The LED will turn off.

C. Redial

Using the handset

1. Lift up the handset, press the REDIAL button to initial a redial call.

2. To end the call, place the handset back on the cradle.

D. Speakerphone Volume

Adjust the Vol+ or Vol- button to increase or decrease the speakerphone volume.
Alternatively, go on to the Web Portal, go to Phone Settings page and adjust the volume
settings (see next page).

E. Ringer Volume

Go on to the Web Portal, go to Phone Settings page and adjust the volume
settings (see next page).

FG1066-IP(1S)SP

Figure 1 - Handset volume on the "Phone Settings" page on Web Portal

F. Call Flash

1. During a conversation using the handset, press the FLASH button.

2. The previous conversation is automatically put on-hold.

3. Listen for dial-tone coming from the handset receiver.

4. To place another call, simply press the desired number on the keypad and wait for 5
seconds or press "#" to dial out immediately.

G. Call Hold

1. During a conversation using the handset, press the HOLD button.

2. The other end of the call is now put on-hold. Hold music is generated by the PBX to the
other end.

3. To deactivate the call-hold, press the HOLD button again.

H. Mute

1. During a conversation, press the MUTE button

2. The other end is not able to hear you but you can continue to hear from the other end.

3. To deactivate Mute, press the MUTE button again.