Installation Guide
& User's Manual
UNDER CABINET
RANGE HOOD
UC30
UMC30
Thank you for your purchase. We know that
you have many brands and products to
choose from and we are honored to know that
you have decided to take one of our products
into your home and hope that you enjoy it.
Our appliances are designed according to
the strictest safety and performance standard
for the North American market. We follow the
most advanced manufacturing philosophy.
Each appliance leaves the factory after
thorough quality inspection and testing. Our
distributors and our service partners are
ready to answer any questions you may have
regarding how to install, use and care for your
range hood.
We hope that this manual will help you
learn to use the product in the safest, most
effective manner, and care so that it may give
you the highest satisfaction in cooking for
years to come. If you have any questions or
concerns, please contact the dealer from
whom you purchased it, or contact our
Customer Support at: 1-888-784-3108.
The manual also includes directions for the
professional installer that will install the
product in your home. We recommend using
trained personnel for professional installation.
Please keep th
is manual for future use.
Thank You
STAINLESS STEEL BAFFLE FILTERS
About Your New Filters
Stainless Steel Baffle Filters do not need linings or mesh inside of the
filters. Our Baffle filters are completely constructed out of stainless
steel. The stainless steel construction allows them to be used again
after being cleaned or going through the dishwasher.
How do Baffle Filters Work?
Baffle filters function by forcing the grease filled air to quickly and
continuously change direction as it passes through the filter. The
grease is unable to change direction as fast as the air carrying them,
they end up getting caught on the metal blades and then trapped into
the filter tray. These filters are both efficient and require less
maintenance.
1
Read all instructions before using this appliance.
Save these instructions for future references
Approved for residential appliances
For residential use only
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
FOR GENERAL VENTILATING USE ONLY. DO NOT USE
TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS
OR VAPORS.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This appliance is
equipped with a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is properly
installed and grounded
.
WARNING - IMPROPER GROUNDING CAN RESULT IN A
RISK OF ELECTRIC SHOCK.
Consult a qualified electrician if the grounding instructions are not
completely understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too
short, have a qualified electrician install an outlet near the
appliance.
CAUTION
To reduce risk of fire and to properly exhaust air, do not
vent exhaust air into spaces within walls, ceilings, attics,
crawl spaces, or garages.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK. I
nstall this hood in accordance with all
r
equirements specified.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, READ THE FOLLOWING:
1
. Us e th is u ni t onl y in t he m an ne r inten de d by t he
m
an uf ac tu rer. If yo u h av e questio ns , co ntact t he
m
an uf ac tu rer.
2. Be fo re s er vi ci ng or c le an in g th e u ni t, s wi tc h po wer off a t
s
er vi ce pa ne l a nd lo ck se rv ic e p an el di sc on ne ct ing m eans
t
o pre ve nt po we r fro m be in g s wi tc he d o n acciden ta ll y.
W
he n t he s ervice di sc on necting m ea ns ca nnot be lo ck ed ,
s
ec ur el y f as te n a p ro minent wa rn in g d ev ic e, su ch as a t ag ,
t
o the s er vice pa ne l.
3. In st al la ti on W ork a nd E le ct ri ca l Wirin g Mu st B e Do ne B y
Q
ua li fie d P er so n( s) In Ac co rd ance Wi th al l A pp li ca bl e
C
od es & S ta nd ar ds , I nc lu di ng Fi re -r at ed Co ns tructio n.
4. Su ffi ci en t ai r is ne ed ed f or p ro per com bu st io n an d
e
xh au st in g o f gas es t hr ough th e fl ue ( Chimney) of fu el
b
ur ni ng eq ui pment t o p re ve nt ba ck - d ra ft in g. Fo ll ow th e
h
ea ti ng eq ui pment m an uf ac turers gu id el ine a nd sa fe ty
s
ta nd ar ds su ch a s t ho se pu bl is he d b y the N at io na l F ir e
P
ro te ct io n A ss oc ia ti on (N FPA), t he Am er ic an S oci et y for
H
ea ti ng , R ef ri ge ra ti on an d A ir Co nd it io ni ng En gineers
(
AS HR AE ), an d t he lo ca l c od e authori ti es .
5. Wh en c ut ti ng o r d ri ll in g in to w all o r ce il in g, d o not d am ag e
e
le ct ri ca l w ir in g a nd o ther hi dd en ut il ities.
6. Du ct ed s ys te ms mu st a lw ay s be v ented t o th e o ut do or s.
WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This
Hood With Any External Solid State Speed Control Device.
WARNING
WARNING
Unplug or disconnect the appliance from the power
supply before servicing.
TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF
A RANGE TOP GREASE FIRE, READ THE FOLLOWING:
A. SMOTHER FLAMES with a close - fitting lid, cookie sheet, or other
metal tray, then turn off the gas burner or the electric element.
B. BE CAREFUL TO PREVENT BURNS. If the flames do not go out
immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
C. NEVER PICK UP A FLAMING PAN - DO NOT USE WATER, including
wet dishcloths or towels - a violent steam explosion will result.
Always leave safety grills and filters in place. Without these
components, operating blowers could catch onto hair, fingers
and loose clothing. The manufacturer declines all responsibility
in the event of failure to review the instructions given here for
installation, maintenance, and suitable use of the product.
The manufacturer further declines all responsibility for injury
due to negligence and the warranty of the unit automatically
expires due to improper maintenance.
2
3
PARTS DIAGRAM
UC30 / UMC30
Grease Filters
MAIN PARTS
Main body
9 - 3/4"
29-1/2"
12 "
6"
4
2 pcs - 5x50 wood screws
2 pcs - Wall Anchors
5 pcs - 5x16 wood screws
6” Round Aluminum Duct
2 pcs 2 pcs 5 pcs
PARTS INCLUDED
PARTS REQUIRED
Measuring tape Level
Pencil Tape
Phillips screwdriver
Flathead
screwdriver
Hammer Electric drill
Safety goggles
Safety gloves
5
FRONT VIEW
TOP VIEW
29 - 1/2”
9 - 3/4”
27 - 1/2”
1”
1”
HOOD
MOUNTING
SCREWS
BACK
6”
10 - 3/4”
9 - 1/8”
1 - 1/2”
20 - 1/2”
12”
CABINET FRONT
1”
3 1/2”
1 - 1/4”
ELECTRICAL
ACCESS HOLE
(IN CABINET BOTTOM)
UC30 / UMC30
6
PRE-INSTALLATION REQUIREMENTS
1. Do not install the Range Hood where there are many dorrs or win-
dows in order to avoid effecting the exhaust efciency caused by air
convection.
2.
Install
the Range hood directly above the cooking surface. The
recommended distance between the cooking surface and the bottom
of the range is minimum 24” and Maximum 30”.
3.
In order to get the optimum performance, do not extend the vent pipe
too far , a
dj
ust the vent pipe, and make sure the hood is level and
vertical.
4.
The air out
l
et must not be connected to chimney flues or combustion
gas ducts. The air outlet must not be connected to ventilation ducts
for rooms in which fuel-burning appliances are installed.
HOOD MAY HAVE SHARP EDGES; PLEASE WEAR PROTECTIVE
GLOVES IF ITS NECESSARY TO REMOVE ANY PARTS FOR
INSTALLING, CLEANING, OR SERVICING.
SAFETY WARNING
7
4. Take the hood unit along with the 6” Round Aluminum duct (Part D). Secure the round aluminum duct to the vent hole at the top of the hood unit using HVAC Aluminum foil tape.
5. If mounting to the wall only, drill a 6-1/4” round hole on the back wall above the hood, OR
into the ceiling directly above the hood.
5b. Lift the hood and hang the hood unit on the back wall using the screws drilled in Step 3.
Once the hood is securely hung on the wall, tighten the screws from the interior of the hood.
5c. Pull round aluminum duct through the newly drilled hole in the wall. Plug unit into power
Step 4 Step 5
1. 1. Drill two 8mm holes in position for Wall Anchor (Part B) placement.
(See Page 5 for placement location).
2. Tap Wall anchors securely into each of the drilled holes.
3. After Wall anchors have been tapped in place, Insert 5x50 wood screws, but leave 1/4” of
the screw sticking out of the wall.
(This will give your Range Hood something to hang onto).
Step 1-3
If mounting to a cabinet, skip step 5 and proceed with steps 6-11.
INSTALLATION PROCEDURES
OR
6. Drill a 6 - 1/4” Round Hole into the bottom of the cabinet. Drill a 1 - 1/2” hole into the bottom
of the cabinet for the Electrical Access hole.
See Page 5 for hole location according to the diagram (Top View).
6a. Pull the round duct & power cord through the bottom of the
cabinet holes.
7. Lift the hood and hang the hood unit on the back wall using the screws drilled in Step 3.
8.
the
hood.
9. Drill each of the five pieces of 5x16 wood screws (
Part C) into the bottom of the cabinet
10. Once the hood is secured into the cabinet
tighten the wood screws located in the back
of the hood.
Baffle filters back into place. Make sure hood is secure by pressing
on it. Plug unit into power outlet.
Step 7
Step 8-9
Step 6
8
ELECTRICAL
ACCESS HOLE
9
IMPORTANT SAFETY INSTRUCTIONS
NOTE: The appliance is not to be used by children or persons with
reduced physical, sensory, or mental issues, or lack of experience, and
knowledge. Unless, they have been given supervision or instruction.
Do not connect the air
outlet to chimeny fuels or
combustion gas ducts.
In case of any damage to
powere cable, replace the
broken cable with a new
one by a qualied person.
Clean the hood correctly
in accordance with the
instructions or it might
cause the possibility of re
or operation problems.
Do not leave unattended
open ames under this hood
10
Replacing the LED lamp
should be performed by a
qualied person. Always
use an LED light 2W or
less.
Never pull the plug out
of the power supply with
wet hands to avoid the
possibility of electric shock.
Disconnect the hood
from the power supply
if the appliance will not
be used for an extended
period of time.
Please do not allow
Children to operate the
device without proper
supervision.
Never wash the control
switch with water or it will
cause electrical problems for
the hood.
A. Light - Press to turn light on / off.
B. Highest Fan Setting
C. Medium Fan Setting
D. Lowest Fan Setting
E. Power Button - Press to turn unit on / off.
How to use the Push Button
When shutting off press once to delay shut-off for
1 minute, or press twice to shut off immediately.
How to use the Push Button
11
UC30
COMPATIBLE WITH MODELS:
12
Soft Touch Controls
UMC30
COMPATIBLE WITH MODELS:
(Starts Max Fan Speed)
MAINTENANCE
CAUTION: Never put your hand inside the unit while it is
operating. For the best performance clean your unit frequently.
C
LEANING:
1. Use only mild soap or cleaning solutions to clean the range
hoods outer surface. Dry surfaces using a soft cloth.
2. Stainless Steel cleaner may be used on the external surface.
3. Cleaning the Baffle Filters: For daily cleaning, use hot, soapy
water and a soft cloth. Wipe dry and finish with a damp microfiber cloth. Baffle filters can also be cleaned in the dishwasher.
4. Clean the Range Hood assembly once every 6 months.
5. D
O NOT clean motor or electrical components with water or
any other liquid.
CAUTION: LED LAMP UNIT IS HOT! WAIT BEFORE ATTEMPTING
BEFORE ATTEMPTING TO REPLACE LED LAMPS. PLEASE BE
SURE THE UNIT IS POWERED OFF & UNPLUGGED.
NOTE: INDIVIDUAL LED BULBS CANNOT BE REPLACED. ONLY LED LAMPS.
1. Remove the baffle filters
2. Find the wire connection of the lamp and unplug.
3. Remove old LED lamp.
4. Plug in new LED lamp.
5. Reinstall the baffle filters.
REPLACING LIGHT BULBS
13
TROUBLESHOOTING
CAUTION: ALWAYS UNPLUG UNIT FROM POWER BEFORE SERVICING
PROBLEM SOLUTION TOOLS
My range hood is noisy.
A. Check inside the range hood
for any loose debris and
remove.
Phillips Screwdriver
My range hood has
poor performance..
A. The range hood and cook top
are too far away from each
other.
Optimal distance is 24” to 36”
B. There are too many open
windows or doors in the area.
Close some doors or
windows.
C. The motor performance has
decreased due to wear.
Replace motor.
D. Check and make sure the
tape holding down the
damper flaps at the vent hole
are removed before use.
Phillips Screwdriver
My range hood shakes.
A. The installation is not secure.
Check again and make sure
the installation hardware is
securely mounted.
B. The fan is broken or not
balanced. Realign or replace
fan.
C. The motor is loose. Check
and make sure the motor is
solidly mounted to the unit.
Phillips Screwdriver
The motor no
longer runs.
A. Replace control panel or
circuit board.
B. Replace with new motor
assembly.
Phillips Screwdriver
Light bulbs went out.
A. Replace with a new LED
lamp assembly.
Phillips Screwdriver
14
15
Push button control
TROUBLESHOOTING
TECHNICAL INFORMATION
WARRANTY AND SERVICE
Limited Warranty
This unit comes with 5 Year Manufacturer’s Part Warranty. Within
5 years after date of receiving the product, Cosmo will replace
any functional parts that are defective. The customer must
contact Cosmo and provide a description of the defective part,
including digital pictures if requested, along with original proof of
purchase.
Defective components must be returned to Cosmo shipping
prepaid. After the 1st year, shipping costs of replacement parts
will also be prepaid by customer.
Functional parts are those components/parts that are critical to
the performance of the product’s essential function.
Non-functional parts are those that are a cosmetic feature of the
product such as knobs, grates, other metal bodies surfaces, etc.
A. Warranty does not cover failure as result of: misuse, abuse, rust or corrosion,
spilled liquids or foreign objects found inside the unit; repair of damage
caused by accident, theft, fire, flood, external causes such as, but not limited
to, blow fuses, inadequate electrical power, water and gas lines beyond the
equipment, or any use of the product not authorized by the manufacturer.
B. The maximum liability of the warranty for product replacement or repair shall
not exceed the original purchase price of the product.
C. Cosmo reserves the right to repair or replace the covered product with a
comparable feature model of like kind.
D. Warranty does not cover deterioration of the appearance of the product, any
cosmetic part such as paint, porcelain, glass, dents, scratches, chips, rust or
peeling.
E. Any damage resulting from unauthorized replacement parts, improper service
or modifications made to the covered product are not covered.
F. Cosmo is released from all liability due to indirect, consequential or incidental
damages.
G. If replacement unit(s) is needed, shipping will be paid by the customer.
TO RECEIVE WARRANTY SERVICE, YOUR PRODUCT MUST BE REGISTERED.
TO REGISTER, VISIT: WWW.COSMOAPPLIANCES.COM/WARRANTY
16
Loading...