Cosmo COSKF863C User Manual

KITCHEN FAUCET
MODEL: COS-KF863C
USER’S MANUAL & INSTALLATION GUIDE
Thank You
Thank you for your purchase. We know that you have many brands and products to choose from and we are honored to know that you have decided to take one of our products into your home and hope that you
enjoy it.
Our faucets are designed according to the strictest performance standards for the North American market. We follow the most advanced manufacturing philosophy. Each faucet leaves the factory after thorough quality inspection and testing. Our distribu tors and our service partners are ready to answer any questions you may have regard ing how to install, use and care for your
faucet.
We hope that this manual will help you learn
to use the product in the safest and most effective manner and care for it so that it may give you the highest satisfaction for years to come. If you have any questions or
concerns, please contact the dealer from whom you purchased it, or contact our Cus­tomer Support at
1-888-784-3108.
The manual also includes directions for the professional installer that will install the product in your home. We recommend using
trained personnel for professional installation.
Please keep this manual for future use
1
2
Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Cosmo
Appliances at 1-888-784-3108
Pre-drilled hole size requirement: 1-3/8” - 1-1/2”
Max countertop thickness without deck plate: 1-3/8”
Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean the sink of countertop to remove and debris, plumber's putty, and silicone.
Place a bucket under the angle stops. Turn on to clear any debris prior to
installing new plumbing. Shut off angle stops.
TABLE OF CONTENTS
PARTS DIAGRAM
PARTS INCLUDED
FAUCET DIMENSIONS
INSTALLATION PROCEDURES
OPERATING INSTRUCTIONS
TROUBLESHOOTING
04
05
06
08
12
14
3
10
44
5
6
The minimum distance between the faucet hole and the wall should be 3.5”. This is to ensure that the faucet lever can move freely allowing for full operation.
If the distance between the faucet hole and the wall is less than 3.5”, you may position the faucet lever 30 degrees to 90 degrees off of the wall to allow for full operation
7
Step 1
A. Plastic Holder
B. Silicone Ring
C. Metal Ring
D. Nut
E. Screws
Remove the plastic holder, silicone ring, metal ring, and nut from the shank.
Insert faucet through the top hole of installation site. Attach Plas­tic Holder (A), Silicone Ring (B), Metal Ring (C) under the faucet. Use the Nut (D) provided to hold sink and hardware into place. Once tightened, use the Screws (E) located on the nut to firmly secure into place.
8
Step 2
A. Supply Hose
B. Spray Hose
C. Supply Hose
C. Supply Hose
Connect spray hose (B) to supply hose (A).
Connect the hot and cold hoses to the hot and cold supply hoses of the faucet. Hoses on the faucet are labeled.
9
Step 3
Proper tracts smoothly. On the sprayer hose measure 15" down from the body of the faucet and mark this point. Install the hose weight at this marked point. The sprayer should retract smoothly. Reposition the hose weight as necessary. Make sure the hot and cold hoses do not interfere with the spray hose. They can be repositioned slightly if necessary.
installation of the hose counterweight will ensure that the sprayer re-
10
Step 4
Connect
Connect hot and cold waterlines (12) to the angle sto and tighten with
plumbers tape on the water supply threads). Turn on the water supply
a wrench until snug, then unscrew spray head (8 YET),
and check for leaks (DO NOT TURN FAUCET ON:&5
If no leaks are found turn the faucet on for 60 seconds to clear any debris
from the water lines.
and tighten waterlines to hot and cold water supply (use
11
Usage
How to Operate the Handle
1. Pull the lever to the right to
turn on the water. Push to the
90˚
O
25˚
On
left to turn o
2. Pull the lever forward
(
towards you) to increase cold water flow and push the lever back (away from you) to increase the hot water flow.
12
LEFT
COLD WATER
RIGHT HOT WATER
Usage
How to
Operate the Sprayer
1. Turn the top position on button, for spray function.
on the handle, press
2. Turn on the handle,
press the down position
on button, the flow will come from the middle
13
Troubleshooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
O B L E M C A U S E A C T I O N
P R
Leakage under the handle.
Water will not shut off completely
Locking nut has come loose .
Cartridge needs to be replaced.
Unscrew the lever on the handle by hand. Loosen set screw with a hex wrench (2.5 mm). Re­move the handle and
unscrew USJNDBQ
by hand. Tighten locking nut with an adjustable wrench
Unscrew the lever on the handle by hand. Loosen set screw with a hex wrench (2.5 mm). Remove the handle
and unscrew USJNDBQ
by hand. Un­screw the locking nut with an adjustable wrench. Replace ce­ramic disc cartridge.
14
king between spray
Lea
ead and the hose
h
Spray head may be loose or washer is not seated correctly in the hose connection
Tighten the spray head by hand until snug. Make sure the washer is seated correctly
Codes/Standards Applicable:
WAR
• Certified t
• Certified to AB1953
• Certified to NSF/ANSI 61
ADA for lever handle
o CUPC
RANTY AND SERVICE
For full warranty details on this product please visit:
http://www.cosmoappliances.com/warranty
15
Loading...