Thank you for your purchase. We know that
you have many brands and products to
choose from and we are honored to know
that you have decided to take one of our
products into your home and hope that you
enjoy it.
Our faucets are designed according to the
strictest performance standards for the
North American market. We follow the most
advanced manufacturing philosophy. Each
faucet leaves the factory after thorough
quality inspection and testing. Our distribu
tors and our service partners are ready to
answer any questions you may have regard
ing how to install, use and care for your
faucet.
We hope that this manual will help you learn
to use the product in the safest and most
effective manner and care for it so that it
may give you the highest satisfaction for
years to come. If you have any questions or
concerns, please contact the dealer from
whom you purchased it, or contact our Customer Support at
1-888-784-3108.
The manual also includes directions for the
professional installer that will install the
product in your home. We recommend using
trained personnel for professional
installation.
Please keep this manual for future use
1
2
Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Cosmo
Appliances at 1-888-784-3108
Max countertop thickness without deck plate: 1-3/8”
Turn off the hot and cold water supply at the angle stops and turn on the
old faucet to release any built up pressure. Remove existing faucet.
Clean the sink of countertop to remove and debris, plumber's putty, and
silicone.
Place a bucket under the angle stops. Turn on to clear any debris prior to
installing new plumbing. Shut off angle stops.
TABLE OF CONTENTS
PARTS DIAGRAM
PARTS INCLUDED
FAUCET DIMENSIONS
INSTALLATION PROCEDURES
OPERATING INSTRUCTIONS
TROUBLESHOOTING
04
05
06
08
11
12
3
FAUCET PARTS DIAGRAM
4
4
5
6
The minimum distance between the
faucet hole and the wall should be 3.5”.
This is to ensure that the faucet lever can
move freely allowing for full operation.
If the distance between the faucet hole
and the wall is less than 3.5”, you may
position the faucet lever 30 degrees to
90 degrees off of the wall to
allow for full operation
7
Step 1
A. Plastic Holder
B. Silicone Ring
C. Metal Ring
D. Nut
E. Screws
Hardware will be attached to the faucet
during shipping. Remove hardware from
the faucet to begin installation. Remove
the Nut, Metal Ring, Silicone Ring and
Plastic Holder. Set aside this hardware for
the next installation step.
Step 2
Insert faucet through the top hole of installation site. Attach Plastic Holder (A),
Silicone Ring (B), Metal Ring (C) under
the faucet. Use the Nut (D) provided to
hold sink and hardware into place. Once
tightened, use the Screws (E) located on
the nut to firmly secure into place.
8
Step 3
A. Supply Hose
B. Spray Hose
C. Hose
C. Hose
Connect spray hose (B) to supply hose
(A).
Connect the hot and cold hoses (C).
Hoses will be labeled on your actual
product.
Step 4
Proper installation of the hose
counterweight will ensure that
the sprayer retracts smoothly.
On the sprayer hose measure 15"
down from the body of the
faucet and mark this point. Install the hose weight at this
marked point. The sprayer
should retract smoothly. Reposition the hose weight as necessary. Make sure the hot and cold
hoses do not interfere with the
spray hose. They can be repositioned slightly if necessary.
9
Step 5
Connect
Connect hot and cold waterlines (12) to the angle sto and tighten with
plumbers tape on the water supply threads). Turn on the water supply
a wrench until snug, then unscrew spray head (8YET),
and check for leaks (DO NOT TURN FAUCET ON:&5
If no leaks are found turn the faucet on for 60 seconds to clear any debris
from the water lines.
and tighten waterlines to hot and cold water supply (use
10
Usage
How to Operate the Handle
1. Pull the lever to the right to
turn on the water. Push to the
90˚
O
25˚
On
left to turn o
2. Pull the lever forward (to
wards you) to increase hot
water flow and push the
lever back (away from you)
to increase the cold water
flow.
Left
Hot Water
Right
Cold Water
11
Troubleshooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
P R O B L E MC A U S EA C T I O N
Leakage under the
handle.
Water will not shut off
completely
Locking nut has
come loose .
Cartridge needs to be
replaced.
Remove the small
chrome colored cap
with red and blue (hot/
cold) dots. Remove the
lever by loosening the
set screw inside the hole
with a hex wrench.
Tighten the locking nut.
Remove the small
chrome colored cap
with red and blue (hot/
cold) dots. Remove the
lever by loosening the
set screw inside the
hole with a hex
wrench. Remove the
locking nut and replace the cartridge.
12
Leaking between spray
h
ead and the hose (
Spray head may be
loose or washer is not
seated correctly in the
hose connection
Tighten the spray head
by hand until snug.
Make sure the washer
is seated correctly
Codes/Standards Applicable:
HELP LINE
Our customer service hours are Monday – Friday, 10am – 5pm PST.
Be sure to visit our website at www.cosmoappliances.com
If you are a homeowner please contact a Cosmo Appliances Service Representative at:
1-888-784-3108
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
For full warranty details on this product please visit:
http://www.cosmoappliances.com/warranty
13
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.