Cosmetal River 50 Up, River 25, River 15, River 25 Up, River 50 User Manual

River Service

2

River 15

- cold water production (10°C): 15 litres per hour

- compressor: 1/10 HP

- condensation: Static

River 25

- cold water production (10°C): 25 litres per hour

- compressor: 1/6 HP

- condensation: Ventilated

River 50

- cold water production (10°C): 50 litres per hour

- compressor: 1/4 HP

- condensation: Ventilated

3

River 25 UP

- cold water production (10°C): 25 litres per hour

- compressor: 1/6 HP

- condensation: Ventilated

River 50 UP

- cold water production (10°C): 50 litres per hour

- compressor: 1/4 HP

- condensation: Ventilated

4

River - Hydraulic Circuit

N. CODICE DESCRIPTION

1

2521412 BULKHEAD CONNECT. NICKEL-PLATED 3/8F-1/2M

2

2521367 EQUAL ELBOW JG 8

3

2521363 STEM ADAPTOR JG 3/8M - 8

4

1501302 EVERPURE FILTER

5

2521360 STRAI GHT ADAPTOR JG 3/8M - 8

6

8150120 6 1 DIRECT COOLING SYSTEM RIVER 15
8110020 1 1 DIRECT COOLING SYSTEM RIVER 25
8110030 1 1 DIRECT COOLING SYSTEM RIVER 50

7

2521375 STRAIGHT ADAPTOR JG 1/8M - 8 FOR G62 TAP

8

2521364 EQUAL TEE JG 8

9

2801363 TUBE 8

10

2521366 STRAIGHT ADAPTOR JG FO R G61 TAP

11

2521705 G61 TAP

14

2521706 G62 TAP

15

2781193 MECHENICAL VALVE FOR G63 TAP

16

2521707 G63 TAP

5

Setting up the cooler at your premises

• Examine the packaging for sign of damage, report any damage to

the haulier

• Remove the carton and the plastic bag from the cooler

• Make a general inspection, ensuring that there are no marks or

damage to River and all accessories are present

• Sanitise the cooler

• Replace the plastic bag

• Replace the box over the cooler

• The River is ready for the transportation to the customer

6

Installation

• Place the cooler in the desired point of installation, away from

heat sources and protected from direct sunrays.

• Adjust foot to level the cooler correctly and to avoid irritating

noises caused by vibration.

• When handling and moving the cooler, use the handle recessed

into the cross support on the back of the unit.

• To ensure proper ventilation, position the River at a distance of at

least 6-7 cm from the wall.

7

Assembly and adjustment of faucets 1

Faucet G61

Insert the lever and let it glide on the specific
guiding channel, attach the tube, and tighten it.

The water flow is pre-set by the manufacturer.

If it needs to be adjusted, manipulate ratchet N,
tighten it to increase the flow, loosen it to decrease
it.
Only carry out one revolution at a time.

N

8

Assembly and adjustment of faucets 2

Faucet G62

The faucets G62 are always assembled.

To regulate the water flow, remove ferrule G and
manipulate screw V.

Turning it clockwise will decrease the flow,
anticlockwise movement will in-crease it.

V

G

9

Assembly and adjustment of faucets 3

Faucet G63

The faucets G63 are always assembled.

This faucet is being controlled by a pedal, which
must be attached with a trigger device at the
predetermined location.

The water flow is regulated by manipulating screw S:
turning it clockwise will decrease the flow,
anticlockwise movement will increase it.

S

10

Water connection to the mains

• Before making the water connection, make sure the mains water

pressure is between 1 and 3 bars.

• If the mains water pressure exceeds 3 bars, predispose a pressure

reducer capable of reducing the latter to the 1-3 range.

• Connect the appliance to the water mains using the water inlet

fitting.

• The 3/8F connector or the fast coupling provided can be used for

the 8 mm diameter pipe.

• Predispose a stop tap on the water inlet pipe.