cortet CGW-Z-0010 User Manual

CGW-Z-0010

User Guide

CPD004

The Cortet Z10 Range Extender (CGW-Z-0010) is a device intended for use in various wireless sensor network (WSN), machine-to-machine (M2M), and Internet of Things (IOT)
applications. The Cortet Z10 Range Extender is primarily intended to act as a reliable, secure, and simple way to extend the range and/or capacity of a ZigBee mesh network. The
Z10 is especially useful in large facilities or facilities with a poor RF environment. The Z10 acts as a relay for ZigBee messages between ZigBee devices that are otherwise out of
range – for example, a Cortet Z10 Range Extender can be used to relay messages between ZigBee e nd nodes and an otherwise out of range ZigBee Coordinator such as a Cortet
E100 Gateway. The Cortet Z10 Range Extender can also be used to increase the total number of ZigBee devices that a ZigBee Coordinator can communicate with. This do cument
provides information on the features of the Cortet Z10 Range Extender and how to use it.

IMPORTANT SAFETY INSTRUCTION S

1. READ and KEEP these instructions

2. FOLLOW all instructions

3. DO NOT use this apparatus near water, Dry location use only

4. DO NOT attempt to modify this product. Doing so could result in personal injury

Z10 Features

Package Contents

One Z10 Range Extender
One Plate Screw (see Mounting Tab Use section)

System Requirements

The Z10 acts as an HA 1.2 compliant repeater and range
extender for a ZigBee network. The Z10 requires a
ZigBee Coordinator such as the Cortet E100 Gateway.

Software

The Z10 Area Controller comes with software pre­installed. For information on software updates please see
the mobile app documentation.

Setting up the Z10

To setup the Z10 follow these steps:

1. Ensure a Cortet E100 Gateway (or equivalent
ZigBee Coordinator) has been installed in the
system and is functioning.

2. Use the Cortet mobile app to connect to the
system and enable pairing on the E100.

3. Plug the Z10 into the wall socket.

4. The Z10 will try to pair automatically with the E100
for 5 minutes. If it fails, the button must be
pressed to restart the pairing process.

5. Use the LED table below for current device status.

6. Follow on-screen instructions in the mobile app.

Factory Reset Process

To set the Z10 to factory fresh mode, follow the steps
below. Note: this cannot be undone.

1. Unplug the Z10.

2. Hold the button while plugging the Z10 back in.

3. Continue to hold the button until the LED turns
solid orange and then release the button.

EZ Mode Commissioning

Press and hold the button for 2 seconds. This will invoke
EZ Mode – Network Steering. If not joined to a ZigBee
network, the Z10 will look for a network to join. Once
joined to a ZigBee network the Z10 will turn on permit
joining for 180 seconds to allow any end device to join
the network through it. If already joined to a ZigBee
network, the Z10 will turn on permit joining for 180
seconds.

LE

D behavior

Color

Meaning

Solid Green

Joined to Zigbee network

Green flashing
every 10 sec.

New Software downloading,
Do not unplug

Solid Orange

Not Joined to Zigbee network
/ Device Reset

Blinking Orange

Attempting Network Join

Blinking Blue

Identify Mode

Solid Purple

Lost connection to gateway

Mounting Tab Use

CAUTION - The Z10 has an integral mounting tab for
optional semi-permanent attachment to a grounded 15­ampere, 125-volt duplex receptacle. Use only with
duplex receptacle having center screw.

NOT

ICE - Local Regulations in Canada do not permit

use of a mounting tab. In Canada, do not use the
mounting tab to attach the unit to an outlet

Risk

of Electric Shock – Disconnect power to the

receptacle before installing or removing the unit. When
removing receptacle cover screw, cover may fall across
plug pins or receptacle may become displaced

1

. Using a standard slotted screwdriver, remove the

center plate screw from the wallplate (do not
remove the wallplate itself).

2. Plug the device into the receptacle, oriented such
that the mounting tab hole lines up with the wall
plate screw hole.

3. Secure unit in place by receptacle cover screw

Specifications

Input AC Voltage 100-240 VAC, 50/60 Hz
Maximum Current Drain 0.07A
Operating Temperature Range -20 to 40C [-4 to 104F]
Product Dimensions (includes mounting tab and blades)

60.3mm x 51.0mm x 59.2mm [2.37" x 2.00" x 2.33"]

Product Dimensions when installed (excludes blades)

60.3mm x 51.0mm x 42.1mm [2.37 in x 2.00 in x 1.66 in]
AC input IEC Type A, ungrounded, non-polarized

Agency Certifications

The CGW-Z-010 has been certified per FCC Part 15
rules and to Industry Canada license-exempt RSS
Standards. To fulfill the FCC and IC certification
requirements, the label is placed on the outside of the
device and contains its own FCC ID and IC as shown
below.

Conforms to FCC Part 15B
FCC ID: W7Z-WD6102
IC: 8254A-WD6102

This ZigBee® Certified product works with other ZigBee
Home Automation™ version 1.2.1 (or prior versions)
products. This device works with a ZigBee Gateway and
HA 1.2.1 compliant devices.

Global 2.4 GHz wireless use
ZigBee® Certified is a registered trademark of the

ZigBee Alliance.

FCC & Canada
Compliance Statement

This device complies with Part 15 of the FCC rules and
with Industry Canada license-exempt RSS Standards.
Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and
(2) This device must accept any interference received,

including interference that may cause undesired
operation.

Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:

1. l'appareil ne doit pas produire de brouillage, et

2. l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.

Warning (Part 15.21)

Changes or modifications not expressly approved by
CEL could void the user's authority to operate the
equipment.