Page 1
Caution : You must read this before you proceed
ROCKING CHAIR
Noble House Home Furnishings LLC
Page 1 OF 10
Page 2
Label Picture Description QTY
A Frame 1
B Seat 1
C Cushion 1
D Pillow 1
E Left Rocking Base 1
Noble House Home Furnishings LLC
Page 2 OF 10
Page 3
F Right Rocking Base 1
Label Picture Description QTY
① Screw (M4*40mm) 11
② Screwdriver 1
Before
Beginning
Assembly:
Marked 'longer'
Rocking Base ends marked 'longer' must be attached to Back Legs
Noble House Home Furnishings LLC
Page 3 OF 10
Page 4
Step 1
Overview
This Rocking Chair has multiple parts and may require up to 30 minutes
to assemble. To give you an overview of the Rocking Chair parts, the
above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
Place the Frame(A) and Seat(B) on a clean, non-marring surface.
Place the Frame(A) with it's Legs facing skywards.
Pillow (D)
Cushion (C)
Seat (B)
Frame (A)
Front Facing
Seat (B)
Frame (A)
Right Rocking Base (F)
Left Rocking Base (E)
Marked 'longer'
Noble House Home Furnishings LLC
Page 4 OF 10
Page 5
Place the Seat(B) on the side of a table, with the backrest facing down
and perpendicular to the Desk Top.
2.1) Place the Frame(A) onto the Seat(B) with the Seat(B) stuck in the
middle of the Frame(A) and align the mounting positions.
2.2) Attach Frame(A) to Seat(B) using Screws(①) with Screwdriver(②).
Do not fully tighten the Screws.
Step 2
Step 2.1
Frame (A)
Seat (B)
Table
Seat(B) stuck in the middle of the Frame(A)
Step 2.2
Table
Frame (A)
Seat (B)
Noble House Home Furnishings LLC
Page 5 OF 10
Page 6
Step 3
Attach Frame(A) to Seat(B) using Screws(①) with Screwdriver(②).
Do not fully tighten the Screws.
Frame (A)
Table
Seat (B)
Noble House Home Furnishings LLC
Page 6 OF 10
Page 7
Step 4
Note: The distance from the back mounting position to the Rocking
Base end is 17.5cm. It is longer than the front mounting position to
the head. The Back Legs must have the longer ends to help prevent
the Rocking Chair from tipping over.
Align the mounting positions of the Left Rocking Base(E) with the
Frame(A) and attach using Screws(①) with Screwdriver(②).
Repeat this process with the Right Rocking Base(F).
Tighten all Screws at all joints in a sequential manner.
Note: There are two mounting sites on the Rocking Bases, please
insert the back foot into the back mounting position first and then
do the same for the front foot, this action should ensure smoother
assembly.
Right Rocking Base(F)
①
Left Rocking Base(E)
Seat (B)
Table
Frame(A)
②
Marked 'longer'
Noble House Home Furnishings LLC
Page 7 OF 10
Page 8
Step 5
Inspect the Rocking Chair and make sure all parts are adequately
connected.
Gently and carefully, sit into to the Rocking Chair.
This would help to align all the parts at all joints.
Then get off the Rocking Chair, and place it facedown.
Proceed to tighten all Bolts and Screws at all joints in a sequential
manner.
If there are still wobbles, loosen the Bolts and Screws and execute this
same process.
Finally, stand the Rocking Chair right side up, and put the Cushion(C)
and Pillow (D) on the Rocking Chair as shown in the picture.
Cushion (C)
Pillow (D)
Left Rocking Base(E)
Right Rocking Base(F)
Frame(A)
Seat (B)
Test for Stability
Marked 'longer'
Noble House Home Furnishings LLC
Page 8 OF 10
Page 9
Step 6
Your Rocking Chair is ready for use.
This Rocking Chair can only be used on a flat, level surface.
Noble House Home Furnishings LLC
Page 9 OF 10
Page 10
Noble House Home Furnishings LLC Page 1 OF 1
Loading...