Page 1
Caution : Please read this carefully before you proceed
ARM CHAIR
Page 1 OF 8
Page 2
Label Picture Description QTY
A Left Arm Panel 1
B Right Arm Panel 1
C Seat 1
D Back Rail 1
E Seat Rail 2
Label Picture Description QTY
①
Bolt (M8*40MM) 11
② Screw (M4*40mm) 5
③
Allen Key 1
④
Screwdriver 1
⑤
Plastic Cap 11
Page 2 OF 8
Page 3
Before
Beginning
Assembly:
Overview
Seat (C)
Left Arm Panel (A)
FRONT FACING
Right Arm Panel (B)
x 2
x 11
x 5
x 11
Page 3 OF 8
Page 4
Step 1
Step 2
This Arm Chair has multiple parts and may require up to some 30
minutes to assemble. To give you an overview of the Arm Chair
parts, the above picture is provided to help you put the various
parts into perspective. Please read through the instructions below
to familiarise yourself with the parts and steps before assembly.
Place the Left Arm Panel(A), Right Arm Panel(B), Seat(C), Back
rail(D) and Seat rail(E) on a clean, non-marring surface.
Seat(C)
Right Arm Panel (B)
Left Arm Panel(A)
Back rail(C)
Seat rail(D)
x 2
①
③
Right Arm Panel (B)
Seat rail(D)
Seat rail(D)
Back rail(C)
Page 4 OF 8
Page 5
Step 3
Position the Left arm panel(A)onto the assembled Right arm
panel(B),Back rail(C) and Seat rail(D) as shown in the picture.
Attach them using Bolts(①) and the Allen Key(③).
Note: If the mounting positions cannot be aligned well and
hinder installation, then sway the Left arm panel(A) lightly
when locking the Bolts, this action should help prevent the
Bolts from getting stuck and ensure smooth assembly.
Do not fully tighten the Bolts at this time.
Position the Back rail(D) and Seat rails(E) onto the Right arm
panel(B) as shown in the picture.
Attach them using Bolts(①) and the Allen Key(③).
Do not fully tighten the Bolts at this time.
Right Arm Panel(B)
③
Right Arm Panel(B)
Seat rail(D)
①
Page 5 OF 8
Page 6
Step 4
Left Arm Panel(B)
Right arm panel(B)
②
④
Seat rail(C)
Table
This is the
assembled frame
Back rail(D)
The back of the Seat(C) must fit flushed to the
Back rail(D)
Page 6 OF 8
Page 7
Step 5
Place the Seat(C) on the side of a table with the backrest facing
down and then put the assembled frame onto the Seat(C)with the
Legs facing upwards as shown in the picture.
Attach the assembled frame to the Seat(C) using Screws(②) and
a Screwdriver(④). Do not fully tighten the Screws at this time.
Note: If there are gaps between the assembled frame and the
Seat(C) which hinder installation, pull the Seat(C) upwards into the
assembled frame.
Finally, stand the Armchair up,cover the assembly holes with
Plastic Caps(⑥)and place it on a LEVEL SURFACE. Inspect it
and make sure all parts are adequately connected. Gently and
carefully, sit into to the Armchair. This will help align the parts at all
joints. Then get up from the Armchair, and place it facedown.
Proceed to tighten all Bolts and Screws in a sequential manner. If
the chair appears uneven or wobbles after tightening the screws
and bolts, loosen them, then proceed to execute this same
process.
Seat(A)
Left Arm Panel(A)
Test for Stability
Right Arm Panel(B)
Page 7 OF 8
Page 8
Step 6
Your Arm Chair is ready for use.
This Arm Chair can only be used on a flat, level surface.
Page 8 OF 8
Loading...