Page 1
Label Picture Description QTY
A Top Panel 1
B Left Side Panel 1
C Right Side Panel 1
Caution : You must read this before you proceed
Please look in the velcro pouch for hardware packs and legs
End Table
Page 1 OF 9
Page 2
D Back Panel 1
E Bottom Panel 1
F Leg 4
G
Drawer Left Side
Panel
1
H
Drawer Right Side
Panel
1
I Drawer Back Panel 1
J Drawer Front Panel 1
K Drawer Base Panel 1
Label Picture Description QTY
①
Cam Bolt 5
Page 2 OF 9
Page 3
②
Dowel
(M8x30mm)
9
③
Cam Nut 5
④
Screw
(M3x12mm)
10
⑤
Screw
(M4x15mm)
21
⑥
Screw
(M3x25mm)
9
⑦
Screw
(M4x35mm)
5
⑧
Metal Plate 4
⑨
Screwdriver
(Not provided)
1
⑩
Drawer Stopper 1
Before Beginning Assembly:
*4
*1
*10
Page 3 OF 9
Page 4
Overview
This End Table has multiple parts and may require up to 30 minutes to
assemble.
To give you an overview of the End Table parts, the above picture is to
help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with
the parts and steps before assembly.
FRONT FACING
Top Panel(A )
Left Side
Panel(B)
Leg(F)
Drawer Front
Panel（J
）
Right Side
Panel（
C
）
Page 4 OF 9
Page 5
Step 2
2.1) Insert Cam Bolt(①) into the mounting positions on Top Panel(A)
using Screwdriver(⑨), attach Drawer Stopper(⑩) to the TopPanel(A)
using Screw(④) with Screwdriver(⑨) as shown.
2.2) Attach Metal Plate(⑧) to the Bottom Panel(E) using Screw(⑤)
with Screwdriver(⑨) as shown.
Step 3
Step 1
Unpack and place all parts on a clean, non-marring surface.
*4
3.1
3.2
G
H
I
Page 5 OF 9
Page 6
Attach Drawer Front Panel(J) into the Drawer Left Side Panel(G) and
Drawer Right Side Panel(H) using Screw(⑥) with Screwdriver(⑨) as
shown.
Step 5
Insert Dowel(②) into the mounting positions on Left Side Panel(B),
Right Side Panel(C) and Top Panel(A), Insert Cam Nut(③) into the
mounting positions on Left Side Panel(B) and Right Side Panel(C),
lock by turning Cam Nut(③) with Screwdriver(⑨)
3.1) Attach Drawer Left Side Panel(G) and Drawer Right Side
Panel(H) to the Drawer Back Panel(I) using Screw(⑥) with
Screwdriver(⑨) as shown.
3.2) Insert Drawer Base Panel(K) into the grooves on Drawer Left Side
Panel(G), Drawer Right Side Panel(H) and Drawer Back Panel(I).
Step 4
⑨
③
B
C
Page 6 OF 9
Page 7
Attach Back Panel(D) to the Top Panel(A), Left Side Panel(B), Right
Side Panel(C) and Bottom Panel(E) using Screw(④) with
Screwdriver(⑨) as shown.
Step 6
Insert Dowel(②) into Left Side Panel(B) and Right Side Panel(C),
attach Bottom Panel(E) to the Dowel on Left Side Panel(B) and Right
Side Panel(C) using Screw(⑦) with Screwdriver(⑨).
Step 7
D
B
A
Page 7 OF 9
Page 8
Step 8
Attach Leg(F) to the Bottom Panel(E), and then turn all legs clockwise
to fasten them tightly.
Step 9
Carefully insert the drawer into the Nightstand.
Note: the load-bearing of Drawer is 5KG.
Your End Table is ready for use.
This End Table can only be used on a flat, level surface.
Page 8 OF 9
Page 9
Page 9 OF 9
Loading...