Corradi PALLADIA flat 2, PALLADIA flat 4, PALLADIA tilted 2, PALLADIA flat 3, PALLADIA tilted 3 User Manual
...
Palladia®
Manuale utente
User manual
Benutzerhandbuch
Manuel utilisateur
Manual del usuario
05146 20.05.2013
28 of 121
CORRADI SPA - USER MANUAL - PALLADIA 20.05.2013
PALLADIA
It is designed and manufactured to customer specifications, to
protect from the sun and elements, snowfall excluded; PALLADIA
must be fixed to a suitable supporting wall and may be used in
winds of up to force 8 on the Beaufort scale as shown in chart (pag.
39).
In the event the above conditions are exceeded, the awning must
be folded up. It is very dangerous to leave the awning open as it
can cause injury.
PALLADIA FLAT VERSION
It is designed and manufactured to customer specifications, to
protect from the sun and elements, snowfall excluded; PALLADIA
must be fixed to a suitable supporting wall and may be used in
winds of up to force 6 on the Beaufort scale as shown in chart 1
(page 39).
MANUAL CONTROL
If PALLADIA® is fitted with manual drive, to open and close the
canvas, insert the manual winding handle in the seat of the gearbox
and turn clockwise (to raise the canvas) or anticlockwise (to lower
the canvas).
ELECTRIC COMMAND
In case of PALLADIA with a wall-switch, push the switch in the low
area in order to move the awning downwards, push it in the up
area to move the awning upwards. Once you release the switch the
awning will stop.
The drive must be installed between 90 and 120 cm off the ground.
RADIOCOMANDO
In case of PALLADIA with a radiocontrol, use the respective switches
to move the awning upwards, downwards or to stop it (see fig.).
A working height of < 2.50 m can generate a risk of shearing/
crushing between the moving part (front terminal tube) and the
fixed part of the structure.
The person starting the manoeuvre MUST be present until the end
of the manoeuvre to ensure that no obstacles or persons are in the
proximity of the potential hazard zone; alternatively the electric
drive can be installed as described on the next page.
Keep out of reach of children
Replacing radio control 1 battery
In order to replace the battery remove the screw on the back of
the radiocontrol and replace the batteries with a similar model
(alkaline 12 Vdc mod. 23 A).
Replacing radio control 2 battery
This transmitter is powered by a CR2032 type 3 Volt battery. To
replace it, open the plate on the back and remove the flat battery,
then replace it with a new one, ensuring the polarity is correct.
Reposition the plate.
Attention: do not invert polarity.
Attention: do not use an incorrect battery type.
Risk of explosion if the battery is replaced with a model
dierent from that specied.
Dispose of the used battery in the appropriate containers.
HOW TO CONTROL PALLADIA
USAGE
Awning going
upwards
Awning going
upwards
Stop
Stop
Awning going
upwards
Awning going
downwards
Led
Indicates the
battery state
(red is working)
Awning going
downwards
Awning going
downwards
29 of 121
CORRADI SPA - USER MANUAL - PALLADIA
ITALIANOENGLISHDEUTSCHFRANÇAISESPAÑOL
20.05.2013
VERSIONS AND MOTORISATIONS
220 volt / 218 watt motor reducer complete with limit switch.
Required for 2, 3 or 4 runner awning, flat version, where the
awning remains slack, or for the taut, tilted version, with a
maximum projection of 350 cm.
220 volt / 218 watt motor reducer with microchip canvas
tension controlled and a radio command (433.92 MHz).
Required for a 2 or 3 - runner awning, tilted version, which
guarantees constant correct tension despite changes in fabric
properties caused by differing environmental circumstances.
220 volt / 218 watt + 218 watt motor reducer with a microchip
that powers 2 motors and controls the canvas tension, a radio
command (433,92 MHz) with 2 channel emitter. Required for
a 4 runner awning, tilted version, which guarantees constant
correct tension despite changes in fabric properties caused
by differing environmental circumstances.
ELECTRIC DRIVE TYPE 1
PLAN motor
ELECTRIC DRIVE TYPE 2
SLOPE motor
remote computing system exchange MO NO
ELECTRIC DRIVE TYPE 3
SLOPE motor 1 (command)
PLUS motor 2
remote computing system exchange TANDE M
PALLADIA 2 RUNNERS
PALLADIA 3 RUNNERS
PALLADIA 4 RUNNERS
TILTED VERSION PALLADIA
FLAT VERSION PALLADIA
1
2
4
3
1
1
1
2
3
4
2
3
4
WIDTH
PROJECTION
WALL BEAM HEIGHT
PILLAR
30 of 121
CORRADI SPA - USER MANUAL - PALLADIA 20.05.2013
PALLADIA 2 RUNNERS
ELECTRIC DRIVE TYPE 1
00775-1 PLAN Motor reducer
ELECTRIC DRIVE TYPE 2
00775-2 SLOPE Motor reducer
00749 MONO Exchange
Wall mounted protection cover
Wall mounted protection cover
Electric drive
Non spinning crosspiece
Frontal crosspiece
Bracket cover
protection hood
Frontal beam (optional)
Frontal beam support
Runner kit cover
Runner kit
Crosspiece drive
Modular awning protection cover
Wall bracket
Bracket cover
protection hood
Lh/rh upper brackets
Crossbar supports
Awning protection
cover cap
Runner
Fixing plate lower bracket
Lower bracket
Pillar
Pillar foot
31 of 121
CORRADI SPA - USER MANUAL - PALLADIA
ITALIANOENGLISHDEUTSCHFRANÇAISESPAÑOL
20.05.2013
PALLADIA 3 RUNNERS
ELECTRIC DRIVE TYPE 1
00775-1PLAN Motor reducer
ELECTRIC DRIVE TYPE 2
00775-2 SLOPE Motor reducer
00749 MONO Exchange
Tettuccio a parete
Wall mounted protection cover
Electric drive
Non spinning crosspiece
Frontal crosspiece
Frontal beam (optional)
Frontal beam support
Runner kit cover
Runner kit
Crosspiece drive
Modular awning protection cover
Crossbar supports
Lh/rh upper brackets
Wall bracket
Awning protection
cover cap
Runner
Fixing plate lower bracket
Lower bracket
Foot
Pillar foot
Bracket cover protection hood
32 of 121
CORRADI SPA - USER MANUAL - PALLADIA 20.05.2013
PALLADIA 4 RUNNERS
Wall mounted protection cover
Wall mounted protection cover
Modular awning protection cover
Crossbar supports
Lh/rh upper brackets
Wall bracket
Awning protection
cover cap
Runner
Fixing plate lower bracket
Lower bracket
Pillar
Pillar foot
Electric drive
Non spinning crosspiece
Frontal crosspiece
Frontal beam (optional)
Frontal beam support
Runner kit cover
Runner kit
Crosspiece drive
ELECTRIC DRIVE TYPE 1
00775-1 PLAN Motor reducer
ELECTRIC DRIVE TYPE 3
00775-2 SLOPE Motor reducer
00775-3 SLOPE Motor reducer
00757 TANDEM Exchange
Bracket cover
protection hood
33 of 121
CORRADI SPA - USER MANUAL - PALLADIA
ITALIANOENGLISHDEUTSCHFRANÇAISESPAÑOL
20.05.2013
TROUBLESHOOTING
PALLADIA
MANUAL VERSION
PALLADIA
ELECTRIC DRIVE
PROBLEM
The awning moves erratically.
The motor won’t start.
The motor starts but the awning won’t move.
The awning moves erratically.
Dirty runners, runners not properly aligned.
There is no electricity.
It is not plugged in.
The motor has overheated.
Problem setting the limit switch.
Possibly broken belts, or disconnection from drive shaft.
Dirty runners, runners not properly aligned.
Clean the runners (see instructions in chapter on maintenance).
Realign the runners.
Check the electric current.
Check that the plug is correctly connected to a suitable socket.
Wait 5-10 minutes to allow the motor to cool down. If the
problem persist check the limit switch.
Set the limit switch.
Contact dealer.
Clean the runners (see instructions in chapter on maintenance).
Realign the runners.
CAUSE CHECKS AND SOLUTIONS
Loading...