coronaDesking iMove-F Assembly Manual
iMove-F Assembly Manual
(Pneumatic Version-H2)
Table of Contents
2
Exploded Desk Diagram
Hardward & Tools
Section 1: Basic Assembly of Desk
Shipped “KD” (knock down)
Unpack and Identify Parts
Assemble Cross Rail to Columns
Connecting Desktop Supports
to Columns
Assemble Work Surface
Support Frame
Attach Work Surface to
Support Frame
Replace Cross Rail Cover
and Trim
Attach Hand Lever
10
11
12
3
Section 2: Attaching the Desk 14
to the Lowboard/Pedestal
4
Attaching Desk to LowboardPedestal
15
5
Section 3: Accessories
17
6
Section 4: Care & Maintenance
6
8
FAQ & Troubleshooting
Section 5: Contact Us
19
22
9
Leveling and Calibrating Desk
13
coronagroupinc • 205.941.1942 • coronagroupinc.com
Work Surface
3
Support Frame
Gas Cylinder
Leg
Gas Cylinder
Support Frame Spanners
Cross Rail Cover
Cross Rail
Foot
coronagroupinc • 205.941.1942 • coronagroupinc.com
pic.1
Tools and Hardware
Required and Recommended Tools
4
Metric Hex Wrenches
(3,4 & 5mm)
6” 4mm T-Handle
Hex Driver
Thumb Bolts —2 ea.
T25 Torx
Driver Bit
8” Driver
Extension
M5 x 20
Socket Cap Bolts —8 ea.
Cordless Driver
Drill
8mm Nut Driver or Box Wrench
#1 Phillips
Driver Bit
8mm Hex Nuts—8 ea.
M6 x 1.0 x 40
Socket Cap Bolts —4 ea.
M6 x 1.0 x 16
Socket Cap Bolts —4 ea.
M5 x 25
Flat Head Screws —8 ea.
coronagroupinc • 205.941.1942 • coronagroupinc.com
M5 x 16 TORX
Button Head s—8 ea.
20mm SPAX
Wood Screws—12 ea.
#4 x 16
Wood Screws —3 ea.
Zip Tie Base—3ea.
Hand Lever Control
4” Zip Ties—3ea.
Section 1: Basic Assembly of Desk
Shipped “KD” (knock down)
-Pneumatic Version-
5
coronagroupinc • 205.941.1942 • coronagroupinc.com
Support Frame
Basic Assembly of Desk Shipped “KD” (knock down)
1.
Work Surface
Gas Cylinder
Identify and uncrate ALL parts
(pic.1 )
NOTE:
1.Not all desks will require two gas
cylinders. The number of gas cylinders will
depend on the size and weight of desk top.
6
Gas Cylinder
Leg
Foot
Cross Rail Cover
Support Frame Spanners
Cross Rail
pic.1
pic.2
2. If user is providing their own custom
top, determine the weight of the top and
contact us to order the appropriate
gas cylinders. (This step should have been
completed at order entry).
Use caution when working with
compressed gas cylinders.
An uncontrolled release could
cause severe damage and/or
personal injury.
Assembling Cross Rail to Columns (Legs)
2.
Use the 8mm nut driver or socket to remove
a.
cross rail cover at indicated positions.
(pic.2-3 )
coronagroupinc • 205.941.1942 • coronagroupinc.com
pic.4
cross rail as seen from below
pic.3
After removing cover, carefully examine the
b.
large torsion spring to ensure it is in its
fully relaxed postion (collasped).
(pic.4 )
WARNING!!! If torsion spring is
in a tight position (expanded)
STOP! Go to Section 5 and
contact coronaDESKING
immediately!
Basic Assembly of Desk Shipped “KD” (knock down)
2.
Assembling Cross Rail to Columns (Legs)
(continued)
Using the 3mm & 8mm wrenches,
c.
loosen/remove the two drive shaft support
bracket bolts at each end of cross rail.
(pic.5 & pic.6)
screws for shaft support
screw from below cross rail
pic.5
long bolt
7
short bolt
pic.6
pic.7
d.
With the “inner leg” FULLY extended join
the cross rail to the leg and carefully insert
the gear into the track. (pic.5) Make sure the
inner leg is FULLY extended and the gear is
properly engaged with the track.
*TIP: The screw head at the end of the
*TIP:
geared track should be aligned with the
approximate center of the drive shaft/gear
when the leg is at max height. (pic.7)
Once cross rail is secured to legs, make sure
e.
the gear is seated with the geared track then
tighten shaft support bracket bolts. (pic.8)
CRITICAL!!! Make sure the
gears in both columns (legs)
are aligned at the exact same
position in each gear track per
above *TIP and picture 7.
coronagroupinc • 205.941.1942 • coronagroupinc.com
pic.8
Loading...