coronaDesking iMove-C Assembly Manual

iMove-C Assembly Manual

(Motorized Version-M1/M2)

Table of Contents

2

Exploded Desk Diagram

Hardware & Tools

Section 1: Basic Assembly of Desk
Shipped “KD” (knock down)

Unpack and Identify Parts

Assemble Cross Rail
to Columns

Connecting Desktop Supports
to Columns

Assemble Work Surface
Support Frame

Attach Work Surface to
Support Frame

Replace Cross Rail Cover
and Trim

10

11

3

Section 2: Attaching the

14

Lowboard/Pedestal

4

Pedestal

Attaching Desk to Lowboard-

15

5

Section 3: Accessories

17

6

6

Section 4: Care & Maintenance

19

FAQ & Troubleshooting

8

Section 5: Contact Us

24

9

Attach Control Panel

Leveling & Calibrating Desk

12

13

coronagroupinc • 205.941.1942 • coronagroupinc.com

Support Frame Spanners

3

Work Surface

Support Frame

Gas Cylinder

Leg

Gas Cylinder

Cross Rail Cover

Cross Rail

Foot

coronagroupinc • 205.941.1942 • coronagroupinc.com

pic.1

Tools and Hardware

Required and Recommended Tools

4

Metric Hex Wrenches
(3,4 & 5mm)

6” 4mm T-Handle
Hex Driver

Thumb Bolts —2 ea.

T25 Torx
Driver Bit

8” Driver
Extension

M5 x 20
Socket Cap Bolts —8 ea.

Cordless Driver
Drill

8mm Nut Driver or Box Wrench

#1 Phillips
Driver Bit

8mm Hex Nuts—8 ea.

M6 x 1.0 x 40
Socket Cap Bolts —4 ea.

M6 x 1.0 x 16
Socket Cap Bolts —4 ea.

M5 x 25
Flat Head Screws —8 ea.

coronagroupinc • 205.941.1942 • coronagroupinc.com

M5 x 16 TORX
Button Head s—8 ea.

20mm SPAX
Wood Screws—12 ea.

#4 x 16
Wood Screws —3 ea.

Control Panel
Mounting Plate—1ea

Zip Tie Base—3ea.

4” Zip Ties—3ea.

Section 1: Basic Assembly of Desk

Shipped “KD” (knock down)

-Motorized Version-M1/M2-

5

coronagroupinc • 205.941.1942 • coronagroupinc.com

Support Frame Spanners

Support Frame

Basic Assembly of Desk Shipped “KD” (knock down)

1.

Work Surface

Gas Cylinder

Identify and uncrate ALL parts

(pic.1 )

NOTE:

1.Not all desks will require two gas
cylinders. The number of gas cylinders will
depend on the size and weight of desk top.

6

Gas Cylinder

Leg

Foot

Cross Rail Cover

Cross Rail

pic.1

pic.2

2. If user is providing their own custom
top, determine the weight of the top and
contact us to order the appropriate
gas cylinders. (This step should have been
completed at order entry).

Use caution when working with
compressed gas cylinders.
An uncontrolled release could
cause severe damage and/or
personal injury.

2.

Assembling Cross Rail to Columns (Legs)

Use the 8mm nut driver or socket to remove

a.

cross rail cover at indicated positions.
(pic.2-3 )

coronagroupinc • 205.941.1942 • coronagroupinc.com

cross rail as seen from below

pic.3

Basic Assembly of Desk Shipped “KD” (knock down)

2.

Assembling Cross Rail to Columns (Legs)

(continued)

Using the 3mm & 8mm wrenches,

c.

loosen/remove the two drive shaft support
bracket bolts at each end of cross rail.
(pic.5 & pic.6)

screws for shaft support
screw from below cross rail

pic.5

long bolt

7

short bolt

pic.6

pic.7

d.

With the “inner leg” FULLY extended join
the cross rail to the leg and carefully insert
the gear into the track. (pic.5) Make sure the
inner leg is FULLY extended and the gear is
properly engaged with the track.

*TIP: The screw head at the end of the

*TIP:

geared track should be aligned with the
approximate center of the drive shaft/gear
when the leg is at max height. (pic.7)

Once cross rail is secured to legs, make sure

e.

the gear is seated with the geared track then
tighten shaft support bracket bolts. (pic.8)

CRITICAL!!! Make sure the
gears in both columns (legs)
are aligned at the exact same
position in each gear track per
above *TIP and picture 7.

coronagroupinc • 205.941.1942 • coronagroupinc.com

pic.8

Basic Assembly of Desk Shipped “KD” (knock down)

3.

Connecting Desktop Supports to

4 Screws

REAR

Allen Screw

Columns

a.

Use a T25 Driver and 4mm Hex Drive to
remove top cover plate from leg assembly.
(pic.9)

8

FRONT

Square Nut

Wing Bolt

pic.9

pic.10

b.

Install gas cylinders as shown (piston down)
(pic.10)

Screw the cylinder piston into bottom plate.
(hand tight)

Re-install supoort plate to column with four

c.

torx-screws, each using the outermost holes.
(pic.9)

Screw in Allen screw. Screw in wing bolt by
hand until hand-tight. Wings must be
parallel to outside edge.
(pic.11)

DO NOT remove square nut at the end
of the cylinder. It should be screwed
down completely on the cylinder and be
UNDER the cover plate once assembled.
(pic.11)

coronagroupinc • 205.941.1942 • coronagroupinc.com

pic.11

DO NOT attempt to operate
desk once the gas cylinders
are installed and before top
is attached. The force of the
cylinders without the weight
of the top could damage the
desk mechanism.