COROB™ D600 - D700 - D800TX
Automatic dispenser
User’s Manual
207119 - ENGLISH V3.0 - R1 (04/2014)
User’s manual
Automatic dispenser
COROB™ D600 - D700 - D800TX
Version 3.0 - R1 (04/2014)
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
© COPYRIGHT 2014, COROB S.p.A.
All rights reserved in all countries
If you require additional copies of this manual or further technical information about it, please write to:
COROB S.p.A.
Via Agricoltura 103 • 41038 San Felice s/P • Modena • Italy
Phone: +39-0535-663111 • Fax: +39-0535-663285
Web site: www.corob.com
Email: info.it@corob.com
INTELLECTUAL PROPERTY RIGHTS AND DISCLAIMER
No part of this manual may be translated into any other languages and/or adapted and/or reproduced in any form, or by any means, electronic
or mechanical, including but not limited to photocopying and recording, without prior written permission of COROB S.p.A..
COROB™ is a registered trademark and/or commercial trademark used on an exclusive basis by COROB S.p.A. and its afliated companies
(hereinafter “COROB”).
A failure of a trademark to appear hereunder does not mean that COROB does not use the trademark in question nor does it constitute a waiver
by COROB of any related intellectual property rights.
Valuable proprietary technical information contained in the present manual are referring to proprietary know-how, designs, drawings and/or
applications used on an exclusive basis by COROB frequently covered by Patents and/or Patent Applications and thus protected by International
and National Intellectual Property Laws.
Unless otherwise indicated, all references to other companies other than COROB and its afliated companies, their names, data and addresses
used in the screens and/or examples are purely coincidental and serve as a reference only to clarify the use of the COROB™ products.
COROB has carefully reviewed the wording and imagines contained in the present manual, nevertheless COROB reserves the right to modify and/
or update the information herein to correct editorial errors and/or inaccuracy of the information herein without notice or commitment on its part.
The present manual contains all information necessary for the foreseeable and normal use of the COROB™ products by the nal user.
The manual does not contain guidelines and/or information for product repair. For safety reasons, only trained and authorized technical personnel
should perform such interventions. Failure to do so may result in personal injury or damage to the product.
For the purpose mentioned above, COROB has appointed authorized technical personnel.
Authorized technical personnel shall mean technicians who have attended a technical training course held by COROB and/or its afliated
companies.
Unauthorized interventions could void the warranty coverage of your COROB™ product pursuant to the sales contract or to the General Sales
Conditions of COROB. COROB can be held responsible only within the limits of the warranty coverage provided by the General Sales Conditions.
COROB does not intend to limit or exclude its liability against any statutory provisions under any applicable law. Therefore the reference to above
warranty limitations or exclusions may not apply.
The nal user can ask COROB or visit the web site www.corob.com for contact details about the nearest authorized technical service.
COROB™ D600 - D700 - D800TX
- 2 -
COROB™ AUTOMATIC DISPENSER
QUICK GUIDE
At the beginning of the working day
• Check that the nozzle center is clean.
• (With humidier system for solvent-based colorants or without humidier system) Check that the sponge is
clean and saturated; if it is necessary to saturate, use only appropriate liquid (the choice of the liquid depends
on the nature of the colorants, and must be done directly by the manufacturer of the products used).
• (With humidier system for water-based colorants) Check that the water in the bottle is not below the
minimum level.
• Carry out system Initialization and Purge.
Things to remember
• Never let the machine OFF.
• In the canisters, stirring of each colorant takes place automatically (stirring times can however be customized).
• Be careful not to ll the canisters with too much colorant. In case of overlling, act as indicated in the user’s
manual.
• The colorant to be poured inside the canisters must be stirred manually. Do not use automatic shakers.
• Close the canisters with their lids right after lling operations.
• Remember to update accordingly the canisters lling levels via the management software.
• (With humidier system for solvent-based colorants or without humidier system) The sponge must be
saturated at least twice a week (the frequency of intervention is indicative, since it depends on the nature of
colorants and the environment conditions).
• (With humidier system for water-based colorants) Top up the water bottle as soon as the minimum level is
reached. Do not exceed the maximum level.
At the end of the working day
• Rell the canisters.
• Update the canister lling levels in the management software.
• Shut down the computer. Do not shut off the machine.
It is recommended to carefully read the user’s manual.
- 3 -
COROB™ D600 - D700 - D800TX
COROB™ D600 - D700 - D800TX
- 4 -
CONTENTS
1 GENERAL INFORMATION ........................................................................................................... 7
1.1 Purpose and use of this manual ...........................................................................................7
1.1.1 Conventionally used graphics ...................................................................................7
1.2 Denitions ........................................................................................................................7
2 FEATURES .................................................................................................................................9
2.1 Description of the machine .................................................................................................9
2.2 Description of units ......................................................................................................... 10
2.3 Standard and optional congurations ................................................................................. 12
2.4 Usable cans .................................................................................................................... 12
2.5 Intended use .................................................................................................................. 13
2.6 Identifying information..................................................................................................... 13
3 SAFETY ................................................................................................................................... 15
3.1 Safety warnings and unauthorized use ............................................................................... 15
3.2 Warnings on the use of colorants ....................................................................................... 16
3.3 Residual risks ................................................................................................................. 17
3.4 Position of labels ............................................................................................................. 18
3.5 Safety devices ................................................................................................................ 19
3.6 Requirements of the installation site ................................................................................. 20
4 SHIPPING AND HANDLING ......................................................................................................21
4.1 General warnings ............................................................................................................ 21
4.2 Unpacking and placement ................................................................................................ 21
4.2.1 Adjusting the support feet ..................................................................................... 24
4.2.2 Standard material supplied .................................................................................... 25
4.3 Installation ..................................................................................................................... 25
4.4 Storage ......................................................................................................................... 25
4.5 Disposal and recycling ..................................................................................................... 26
5 START-UP ............................................................................................................................... 27
5.1 General warnings ............................................................................................................ 27
5.2 Control devices and connections ........................................................................................ 28
5.3 Electrical connection and start-up ...................................................................................... 29
5.4 Initialization ................................................................................................................... 29
5.5 Emergency stop .............................................................................................................. 30
5.6 Shut-down ..................................................................................................................... 30
6 USING THE DISPENSER ........................................................................................................... 31
6.1 General warnings ............................................................................................................ 31
6.2 At the beginning of the working day................................................................................... 31
6.3 Running the machine ....................................................................................................... 31
6.3.1 Loading the can - Semiautomatic shelf .................................................................... 32
6.3.2 Loading the can - Automatic shelf .......................................................................... 33
6.3.3 Loading the can - Panel roll conveyor...................................................................... 33
6.3.4 Use of the can centering device ............................................................................. 34
6.3.5 Use of the Bung Hole Locator ................................................................................. 34
6.3.6 Punching the can ................................................................................................. 35
6.3.7 Dispensing .......................................................................................................... 36
6.4 Automatic processes ........................................................................................................ 36
6.5 Relling the canisters ....................................................................................................... 37
6.6 Troubleshooting .............................................................................................................. 39
7 ORDINARY MAINTENANCE ......................................................................................................41
7.1 General warnings ............................................................................................................ 41
7.2 Maintenance table ........................................................................................................... 41
7.3 Products to be used ......................................................................................................... 41
7.4 External cleaning ............................................................................................................ 42
- 5 -
COROB™ D600 - D700 - D800TX
7.5 Cleaning the nozzle center ................................................................................................ 42
7.6 Cleaning and moistening the humidier cap sponge ............................................................ 43
7.7 Checking and replacing the puncher .................................................................................. 45
7.8 Relling the humidier system bottle ................................................................................. 46
8 TECHNICAL SPECIFICATIONS .................................................................................................47
8.1 Technical data ................................................................................................................. 47
8.2 Dimensions .................................................................................................................... 48
8.3 Declaration of conformity ................................................................................................. 50
8.4 Warranty ........................................................................................................................ 50
COROB™ D600 - D700 - D800TX
- 6 -
GENERAL INFORMATION
1 GENERAL INFORMATION
1.1 Purpose and use of this manual
Read this manual carefully before using the machine.
This manual, inserted in the product packing, contains instructions on the use and routine maintenance needed
to uphold the machine’s performance over time. The manual contains all information needed to correctly use the
machine and avoid any accident.
The manual is to be considered an integral part of the machine, and must be stored until it is fully dismantled.
The manual contains all information available at the time of preparation regarding the machine and any
accessories; for accessories, the manual includes any variations or changes that involve different operating
procedures.
Should it be lost or partially ruined, so that its contents can no longer be read in full, you must request a new
manual from the manufacturer.
If the images contained in this manual show the machine without the guards and/or employees
without personal protective equipment, it is only for the purpose to make clearer the discussion of
the issues.
Some of the illustrations in this manual were taken from prototypes; some details may differ on
machines in standard production.
1.1.1 Conventionally used graphics
Boldface type is used to highlight notes or information of particular importance to a topic.
DANGER
Indicates a risk of personal injury.
WARNING
Indicates a risk of damage to the machine that could interfere with its operation.
Indicates a risk of damage to the machine that could interfere with its operation.
Indicates situations and/or operations that involve the management software installed on the computer.
Indicates situations and/or operations that involve the management software installed on the computer.
1.2 Denitions
OPERATOR
A person familiar with the methods to produce paints or similar products, trained and authorized to operate and
use the machine by its controls and to load and unload production materials with all safety devices installed
and enabled. He or she must work only in safety conditions and is allowed to carry out routine maintenance
operations.
MAINTENANCE TECHNICIAN/INSTALLATION TECHNICIAN
Specialist prepared and trained in a technical eld (mechanical and electrical) and assigned by the manufacturer
to work on the machine to perform machine installation, adjustments, repair breakdowns or carry out
maintenance.
- 7 -
COROB™ D600 - D700 - D800TX
FEATURES
COROB™ D600 - D700 - D800TX
- 8 -
FEATURES
2 FEATURES
2.1 Description of the machine
The COROB™ D600 - D700 - D800TX automatic dispensers are devices to automatically dispense uid
colorant products into containers (metal or plastic canisters, cans or bins) of the size indicated in this manual,
pre-lled with base, to produce nished products such as paints, dyes, enamels, and inks of the desired hue,
chosen by means of the machine management software.
2
5
1
3
2
4
5
3
3
1
4
2
4
5
1
The dispenser consists of:
1. Dispensing area and can handling system.
2. Control panel.
3. Upper covers.
4. Canister lling area.
5. Computer support surface.
The dispenser is fully managed by a normal personal computer that can be provided upon request, since it is
not supplied as standard together with the machine. The manufacturer can also supply a wide range of software
applications to manage all of the machine’s functions.
- 9 -
COROB™ D600 - D700 - D800TX
FEATURES
2.2 Description of units
Canisters
The machine canisters can be of different capacities and are suitable for containing
the product to be dispensed. Covers in the upper part of the machine provide
access for lling the canisters. Each canister has its own lid.
Nozzle Center
The ends of the dispensing pipes coming from the canisters converge and are xed
to the nozzle center, from which the tinting product to ll the can is dispensed.
MAX
Shelf
The can shelf allows for the correct positioning of the can under the dispensing
nozzles.
The Automatic shelf is managed by the computer that controls its
movement and checks that the can placed on it is actually the one selected
for dispensing. A photocell checks for the presence of the can and that the
shelf is correctly positioned.
The Semiautomatic shelf is commanded by the operator with the activation
buttons (two-handed control); the shelf stops when the can is detected by
the photocell.
Tipping panel roll conveyor system
An optional system made up of tipping panel roll conveyors is available to facilitate
the loading of cans; the conveyors are xed to the front panels of the machine
and allow heavy cans to be eased as far as the shelf.
COROB™ D600 - D700 - D800TX
- 10 -
Can centering device
On the machine accessorized with punching system, a centering device is mounted
on the shelf. The can centering device is custom-made based on the size of the
cans to be handled and is useful for aligning them with the nozzle center, so that
the can lid is punched in the middle and dispensing takes place precisely into the
hole created. The can centering device is also available as an optional accessory
to the standard machine, useful for positioning pre-punched cans right under the
dispensing center.
Bung Hole Locator (B.H.L.)
This is a system that emits laser beams that allow the positioning of pre-punched
cans, so that the hole is in line with the center of the dispensing nozzles.
FEATURES
Nozzle Humidier Cap
Colorants tend to dry out; this tendency may be more or less strong depending
on the type of colorant and the environment conditions (temperature, relative
humidity, etc.). To prevent colorants from drying out in the nozzle center, the
machine is equipped with a humidier cap which requires constant maintenance.
The Lift-up Autocap is an automatic humidier cap which ensures that the
nozzles are hermetically sealed. It is managed by the software, which opens
it automatically before dispensing and closes it immediately afterwards.
Manually-operated automatic puncher
The puncher is a device that perforates the can lid. Punching is carried out by
the operator by pushing contemporaneously the semiautomatic shelf activation
buttons (two-handed control); thanks to the upward movement, the shelf pushes
the can resting on it against the puncher, and with a downward movement brings
it to the correct position for dispensing.
No-Dry-Nozzle Humidier System
The humidier system for water-based colorants guarantees the nozzles are
humidied not only with Autocap closed but also during dispensing. The air,
humidied by the water contained in the bottle, is transferred to the nozzles
area. Based on the humidity level detected, the system activates or shuts off
whenever needed.
The humidier system for solvent-based colorants humidies the nozzles when
Autocap is closed. The solvent, contained in a small tank inside the Autocap,
keeps the nozzles area constantly saturated.
The two systems can be used individually or together according to the tinting
system used on the machine.
- 11 -
COROB™ D600 - D700 - D800TX
FEATURES
2.3 Standard and optional congurations
D600 TE D600 TI D700 D800TX
3 Quarts - 4 Quarts - 6 Quarts - 4 Gallons (3 - 4 - 6 - 15 liters)
Canister capacity
Number of circuits maximum 24 maximum 32
Circuit with Standard pump standard
1.10” (28 mm) (16)
Nozzle center ow diameter*
1.54” (39 mm) (17-20)
1.77” (45 mm) (21-24)
Punching diameter
1.85” (47 mm) (20)
2.17” (55 mm) (21-24)
Additional canister modules maximum 2 maximum 4
Lift-up Autocap standard
Semiautomatic shelf standard optional standard
Automatic shelf optional standard \ optional
9.5 Quarts - 5.3 Gallons (9 - 20 liters)
(only on large additional canister modules)
1.10” (28 mm) (16)
1.54” (39 mm) (17-20)
1.77” (45 mm) (21-32)
47 mm (20)
55 mm (21-32)
Manually-operated automatic
puncher
optional (with semiautomatic shelf) optional
optional (with
semiautomatic shelf)
Panel roll conveyors standard optional
Laser Bung Hole Locator
(B.H.L.)
No-Dry-Nozzle Humidier
System
optional
optional
Circuit with LAB pump optional
Circuit with HF pump** optional
* Hole diameter for pre-punched cans = ow diameter + 0.59” (15 mm). The diameter may also vary based on the partition of water/solvent
circuits of the machine. ** One HF circuit replaces two standard circuits.
2.4 Usable cans
D600 TE D600 TI D700 D800TX
Standard
19.9”
(505 mm)
MAX
With
puncher
17.7”
(450 mm)
Standard
15.9”
(405 mm)
With
puncher
13.6”
(345 mm)
Standard
19.3”
(490 mm)
With
puncher
16.9”
(430 mm)
Standard
17.7”
(450 mm)
With
puncher
15.4”
(390 mm)
MAX
MIN
*
2.8”
(70 mm)
14.2”
(360 mm)
9.3”
5.1”
(130 mm)
2.4”
(61.5 mm)
13.4”
(340 mm)
5.1”
(130 mm)
12.6”
(320 mm)
2.8”
(70 mm)
14.2”
(360 mm)
5.1”
(130 mm)
(235 mm)
MIN
2.3”
(60 mm)
* Due to the high ll level of 1-Pint and 1-Quart cans (0.5 and 1-liter cans), COROB advises not to perforate them.
COROB™ D600 - D700 - D800TX
3.9”
(100 mm)
2.3”
(60 mm)
3.9”
(100 mm)
- 12 -
2.3”
(60 mm)
3.9”
(100 mm)
2.8”
(70 mm)
(360 mm)
(100 mm)
6.1”
(155 mm)
14.2”
3.9”
FEATURES
2.5 Intended use
The machine is intended for professional use to dispense colorants in small, medium and large point of sales or
professional paint stores.
The machine must be used only with cans within the limits set forth in chapter 2.4 (Usable cans), with the
colorants specied in the table of chapter 8.1 (Technical data) and according to the procedures described in this
manual.
Any use of the machine other than that stated, which cannot be implied or deduced from this manual, is to be
considered improper and unintended therefore it voids any manufacturer’s liability arising from non-compliance
with these requirements.
2.6 Identifying information
The machine has an identication plate (chapter 3.4) indicating:
1. Manufacturer’s name.
2. CE and WEEE marking.
3. Machine model.
4. Year of manufacture.
5. Serial number.
6. Electrical specications.
Do not remove or tamper with the identication plate in any way.
- 13 -
COROB™ D600 - D700 - D800TX
SAFETY
COROB™ D600 - D700 - D800TX
- 14 -
SAFETY
3 SAFETY
3.1 Safety warnings and unauthorized use
COMPULSORY
• Read the user’s manual carefully before carrying out any operation on the machine.
• The machine must be used only for its intended purpose.
• Pay close attention to the signs on the machine.
• When prescribed, wear personal protective equipment.
• Only qualied and appropriately trained personnel (MAINTENANCE TECHNICIAN) are authorized to access the
machine parts protected by panels for extraordinary maintenance and repair interventions.
• Any routine maintenance intervention performed by the operator must be carried out with the machine off
and the power supply cable disconnected from the mains socket outlet.
• The machine must be used by a single operator. Unauthorized people who could reach or touch machine
parts during operation must not be admitted in the nearby area.
• The machine must be used by an operator who has attained the age of majority and is in suitable psychophysical
conditions dened by an occupational physician.
• The substances that may be used on the machine -- such as colorants, paints, solvents, lubricants and
cleansers -- may be hazardous to your health; handle, store and dispose of these substances in keeping with
current regulations and the instructions provided with the product.
PROHIBITED
• The machine must not be used with cans exceeding the limits set forth in chapter 2.4 (Usable cans) and with
colorants other than those specied in the technical data table.
• THE MACHINE MUST NOT BE USED IN AREAS AT RISK FOR EXPLOSION.
• The machine must not be employed for food use.
• The OPERATOR must not carry out operations reserved to the MAINTENANCE TECHNICIAN or the
INSTALLATION TECHNICIAN. The manufacturer CANNOT BE HELD RESPONSIBLE for damages deriving from
the non-observance of this prohibition.
• It is strictly forbidden to use the machine without protections or with any safety devices present on the
machine disabled, broken down, or removed. The panels must be kept closed at all times.
• Do not stare the light source of the Laser Bung Hole Locator (Class II laser product).
• If the machine catches re, never use water. Use only dry powder or carbon dioxide re extinguishers, and
strictly follow the instructions and warnings indicated by the manufacturer and listed on the extinguisher.
ELECTRICAL DANGER
• ALWAYS PLUG THE MACHINE INTO A SOCKET THAT ENSURES PROPER GROUNDING. The line must
be protected from overloads, short-circuits and direct contacts according to current accident prevention
regulations. Incorrect grounding may lead to the risk of electrical shock.
• The machine must not be powered by a power source having specications other than those listed on the
identication plate.
• In the event of a sudden power outage, when power returns the machine will automatically be switched on
to allow the automatic processes to prevent products from drying out.
• To prevent any risk of electrical shock or injuries, use the machine indoors only. It is prohibited to use the
machine outdoors where it could be subjected to rain or high humidity.
• Always unplug the power supply cable from the socket outlet before carrying out any maintenance operations.
• The machine is isolated from the power supply line when the power cable is disconnected; it must therefore
be installed near an easily accessible mains socket outlet.
• Do not use extension cords to power the machine.
- 15 -
COROB™ D600 - D700 - D800TX
SAFETY
• Do not use multisockets to connect other equipment to the same socket that powers the machine. Make
sure that the power supply of the equipment connected to the machine via serial port, like the computer, is
equipotential (which has a single access point to earth) because potential differences cause interferences
and/or damage to the serial ports.
• Periodically check the condition of the power supply cable; if it is damaged, replace it with a new cable
supplied by the manufacturer.
3.2 Warnings on the use of colorants
DANGER
The machine is suitable for use with tinting products in general. Scrupulously follow the instructions for use
given on the colorant package and carefully read the MATERIAL SAFETY DATA SHEETS (MSDS) that the
dealer or manufacturer of the product is required to provide.
Observe all of the safety instructions provided. When compulsory, wear the specied personal protective
equipment.
Below are some of the most common warnings and safety precautions provided by colorant manufacturers.
1. Harmful if swallowed.
2. Avoid eye and skin contact. In case of eye and skin contact, rinse with plenty of water.
3. Keep out of the reach of children.
4. When compulsory, wear the specied personal protective equipment.
5. In case of accidental product leaks or spills, thoroughly ventilate the area and proceed as indicated in this
manual and in the instructions provided with the product itself.
6. Do not dispose of colorant in the sewage system. Follow local regulations when disposing of waste.
COROB™ D600 - D700 - D800TX
- 16 -
3.3 Residual risks
Risk Preventive measure P.P.E.
Risk of electrocution - Risk of electrical
shock if you power the machine from
a socket not equipped with ground
connection.
Risk of electrocution - Risk of electrical
shock if you access machine parts
protected by panels without rst cutting
off electrical power.
Dorsal/lumbar injuries - Handling
heavy loads when moving the machine
and loading cans on the shelf may cause
injuries.
Power the machine through a grounded
socket outlet.
The operator is not authorized to access the
machine parts protected by panels.
For the maintenance technician: before
performing any maintenance intervention,
shut off the machine and disconnect the
power supply cable from the mains socket
outlet.
Do not exceed the weight limits stated by
the current regulations in force (kg 20 for
women, kg 25 for men).
If necessary, use appropriate lifting
equipment.
\
\
SAFETY
Re. in
the
manual
ch. 5
ch. 4 - 6
Risk of falling objects / crushing When positioning a can on the shelf, there
is a risk it may fall onto the operator.
Risk of crushing / entanglement - The
automatic movement of the humidier
cap and of the shelf may cause injuries.
Risk of crushing / entanglement
- During colorant relling operations,
the stirrer inside the canister may
automatically start rotating.
Risk of cuts - During the punching
operations or maintenance operations on
the punching device, the contact with the
puncher blade may cause injuries.
Risk of slipping / falling - Misuse of the
shelf may cause injuries.
Risk of explosion - Fumes generated
by the colorants used may cause an
explosion.
Risk of exposure to laser beam - The
Bung Hole Locator (B.H.L.) uses red laser
light sources which can be potentially
dangerous for the eyes.
Risk of poisoning and sensitization Fumes generated by the colorants used
may cause poisoning and/or sensitization
during canister relling operations,
machine cleaning and disposal.
Position the can so that the whole base rests
on the shelf surface.
The machine must be used by a single
operator.
Keep hands away from the dispensing area
at all times while the machine is operating.
Before performing any intervention, press
the emergency button.
The machine must be used by a single
operator.
Keep hands away from the dispensing area
at all times while the machine is operating.
Use the special tool to remove the puncher.
Do not climb onto the shelf and/or sit on it. ch. 6.3
Do not use the machine in areas at risk for
explosion.
Avoid staring at the light source. ch. 6
Read the warnings reported in the Material
Safety Data Sheets of the colorants used.
The MSDS must be provided by the colorant
manufacturer.
Keep the room suitably ventilated.
Personal
Protective
Equipment
as
specied
in MSDS.
ch. 6
ch. 6
ch. 6.5
ch. 6 - 7
\
ch. 3.2 - 4
- 6 - 7
- 17 -
COROB™ D600 - D700 - D800TX
SAFETY
3.4 Position of labels
6
MODEL
YEAR
MODEL
YEAR
S/N
S/N
1
2
3
726109116X
726106285X
4
5
1. Identication plate (chapter 2.4)
2. Label “General warnings”
3. Label “Risk of crushing”
4. Label “Risk of cuts”
5. Label “Laser danger”
6. Label “Serial ports”
LASER RADIATION
DO NOTSTARE INTOBEAM
CLASS IILASER PRODUCT
1 mWmax
630-650 nm
EN 60825-1:2003
7261010772
726109116X
726106285X
LASERRADIATION
DONOTSTAREINTOBEAM
CLASSIILASERPRODUCT
1mWmax
630-650nm
EN60825-1:2003
7261010772
Do not remove or make illegible the safety or instruction labels. Replace any label which has become
illegible or is missing, by requesting it to the manufacturer.
COROB™ D600 - D700 - D800TX
- 18 -
3.5 Safety devices
1
2
3
SAFETY
1
1. Emergency button.
2. Shelf upper safety plate
(with automatic shelf).
3. Shelf lower safety plate.
4. Safety button to enable shelf operation
(with semiautomatic shelf).
4
3
2
1
3
D600 TE D600 TI D700 D800TX
DANGER
In the event of a breakdown of the safety devices, it is forbidden to use components not provided by the
manufacturer. In case of need, contact only the service organization authorized by the manufacturer.
- 19 -
COROB™ D600 - D700 - D800TX
SAFETY
3.6 Requirements of the installation site
Environment requirements for the site where the machine is to be used:
• Clean and dust-free.
• With level and stable oor.
• Fitted with a grounded power supply socket.
• Equipped with sufcient lighting to ensure good visibility from every point of the machine (light value not
lower than 500 Lux).
• Ventilated to prevent the concentration of harmful fumes.
• Temperature between 10 °C (50 °F) and 40 °C (104 °F) and relative humidity between 5% and 85%, without
condensation.
WARNING
The environment working conditions are strictly related to the type of colorants used (ask for information from
the paint manufacturer). The requirements indicated above are valid for the machine only.
Do not place the machine near heat sources or in direct sunlight. Also humidity sources should be avoided. The
machine must be used indoors only.
Environment conditions outside the values indicated (chapter 8.1) may cause serious damage to the machine,
especially the electronic equipment.
DANGER
When using colorants containing volatile solvents the room in which the machine is installed must be
spacious, with good ventilation (air exchange) and no type of parts must be leant against or stocked close to
the machine.
COROB™ D600 - D700 - D800TX
- 20 -
SHIPPING AND HANDLING
4 SHIPPING AND HANDLING
4.1 General warnings
Personnel in charge of these operations must wear the following personal protective
equipment.
DANGER
To avoid personal injuries and property damage, use the utmost care and caution when handling the machine,
and carefully follow the instructions given in this chapter.
Do not insert the forks of the lift truck into the long side to lift the packing.
WARNING
The packing must be handled only by qualied personnel using appropriate handling equipment. Do not stack
items on the packing.
FRONT SIDE
7261112674
If the machine is installed near a wall, keep it at least 4” (10 cm) away to prevent the cables from being
crushed.
4.2 Unpacking and placement
1 x 10 mm
2 x 17 mm
DANGER
The following procedure must be carried out by at least 2 people.
To remove the xing brackets
Store the packing material for future use, or dispose of it according to current regulations. In any case, we
recommend that you keep it for the entire duration of the machine warranty.
Make sure the packing has not suffered any damage or tampering during shipping; if so, contact the
authorized technical service or your dealer.
1. Cut the straps wrapped around the packing.
2. Remove the covering from the pallet.
- 21 -
COROB™ D600 - D700 - D800TX
SHIPPING AND HANDLING
3. Remove machine wrapping. Take out any accessories and/or material supplied with the machine.
1 2 3
DANGER
Should the machine appear damaged during shipping, do not attempt to start it and contact the authorized
technical service or dealer.
4. Loosen all screws A holding the brackets to the machine.
5. Lower the feet (chapter 4.2.1) so that the machine is slightly raised from the wooden beams on which it
rests.
6. Remove the wooden beams B.
7. Completely unscrew and remove all screws and nuts fastening each bracket C to the pallet.
8. Raise the feet (chapter 4.2.1) until when the machine can move easily on its wheels.
9. Lower both platforms.
10. Grasp the machine on the sides (this must be done by at least two people) then slide it slowly along the
platforms on its wheels, then lower it to the ground.
COROB™ D600 - D700 - D800TX
- 22 -
4 6
A
7
9 10
SHIPPING AND HANDLING
B
C
11. Lower the feet (chapter 4.2.1) to support and level the machine properly, and make sure that the wheels
are not resting.
To repack the machine, follow the unpacking instructions in reverse order. We recommend reusing the original
packing any time the machine must be moved or shipped.
- 23 -
COROB™ D600 - D700 - D800TX
SHIPPING AND HANDLING
4.2.1 Adjusting the support feet
To open machine panels
1 x 19 mm To adjust machine feet
1
2
1
2
c
3
a
a
b
b
COROB™ D600 - D700 - D800TX
- 24 -
4.2.2 Standard material supplied
After unpacking the machine, make sure the following items are present:
SHIPPING AND HANDLING
1
6
2
3
7
4
5
1. Power supply cable.
2. Computer power cables.
3. USB cable.
4. Equipment software tools standard CD.
5. Panel key.
6. User’s manual and product documentation.
8
9
WARRANTY
10
7. Spare parts.
With puncher only:
8. T-wrench.
9. Tool for punch removal.
10. Manual plugger.
Depending on the options specied on the purchase order, you may also nd:
• Management software.
• Any accessories to be installed on the machine.
Make sure that all of the above items are included in the packing; if not, contact the manufacturer.
4.3 Installation
Once the machine has been unpacked and placed in its operating site, it must be installed.
WARNING
Only qualied and appropriately trained personnel are authorized to install the machine.
4.4 Storage
If stored, the machine must be kept in a safe and protected environment, with a suitable temperature and
humidity degree and protected from dust.
- 25 -
COROB™ D600 - D700 - D800TX
SHIPPING AND HANDLING
4.5 Disposal and recycling
This equipment must not be disposed of with unsorted municipal waste. Carry out a
separate collection.
Pursuant to the WEEE Directive, collection, treatment, recovery and environmentally
sound disposal of Waste Electrical and Electronic Equipment (WEEE) shall be carried out
in compliance with the national measures of each EU-Member State implementing the
Directive.
Differentiate the parts making up the machine based on the various materials they are
made of (plastic, iron, etc.).
For the colorants remaining in the canisters, for the machine components most soiled with
colorant and if any products have been used on the machine that require special disposal
procedures, follow local regulations when disposing of waste.
COROB™ D600 - D700 - D800TX
- 26 -
START-UP
5 START-UP
5.1 General warnings
Personnel in charge of these operations must wear the following personal protective
equipment.
DANGER
THIS EQUIPMENT MUST BE GROUNDED. Check the grounding of the power supply system before
connecting the machine.
Do not use extension cords to power the machine.
The computer and any other devices connected to the machine via a serial line or connected to the computer
itself must be powered via the auxiliary sockets.
Do not connect equipment other than computer, label printer or calibration scale to the machine auxiliary
sockets.
Do not use multisockets to connect other equipment to the same socket that powers the machine.
WARNING
Do not attempt to power the machine from a source having specications other than those listed on the
identication plate.
The machine is isolated from the power supply line when the power plug is disconnected; it must therefore be
installed near an easily accessible mains socket outlet.
Do not use multisockets to connect other equipment to the machine auxiliary sockets.
The power supply of the equipment connected to the machine via serial port, like the computer, must be
equipotential (which has a single access point to earth) because potential differences cause interferences and/
or damage to the serial ports.
- 27 -
COROB™ D600 - D700 - D800TX
START-UP
5.2 Control devices and connections
1 3
0
5
2 4 6
7
8
1. Machine main switch.
2. Fuse compartment.
3. Main plug.
4. Auxiliary sockets.
5. Ports for service computer. USB or RS232 connection to the service computer.
7. ON lamp.
8. Emergency button.
6. Ports for management computer.
The value of fuses is shown in the technical specications
table (chapter 8.1).
Power supply to the computer and other equipment (calibration
scale or label printer).
USB or RS232 connection to the machine management
computer.
When this lamp is lit, it indicates that the machine is powered
and the main switch is in the ON position (I).
Red mushroom-head button. This is the emergency stop
button for the machine, to use in case of a breakdown or
dangerous conditions (chapter 5.5).
COROB™ D600 - D700 - D800TX
- 28 -
5.3 Electrical connection and start-up
START-UP
1
0
2
3
b
a
If the ON lamp does not light, make sure the emergency button is not pressed (chapter 5.5). If the
computer and monitor do not come on, make sure the power cables have been properly connected to the
auxiliary sockets, and that the corresponding switches have been turned on..
When the software is launched it offers the operator a series of procedure requests, including initialization
(chapter 5.4). This operation is strictly related to the type of management software used.
5.4 Initialization
INITIALIZATION is a preparatory phase that has to be carried out when the machine is turned on.
If the computer is turned off and back on again, initialization is not strictly necessary, even if required by
the software; it is solely at the discretion of the operator.
DANGER
If the Autocap is open, initialization automatically closes it.
If the automatic shelf is at a certain height it will lower completely.
Moreover, initialization must be carried out in the following cases:
• At the beginning of each work shift, even if only the computer had been shut down.
• To send new operating parameters set via the management software.
• After an emergency stop (chapter 5.5).
For more information about the Initialization function, refer to the software user’s manual.
- 29 -
COROB™ D600 - D700 - D800TX
START-UP
5.5 Emergency stop
In case of a breakdown or dangerous conditions, press the emergency stop button. Pressing this button, power
is cut off to the entire machine and all movements are stopped.
The emergency button does not turn the computer off, since it requires special shut-down procedures (the
auxiliary sockets remain powered).
After eliminating the cause of the malfunction or solved the dangerous condition, reset the button by pulling it.
WARNING
When normal operation is restored, it is necessary to carry out machine initialization (chapter 5.4).
5.6 Shut-down
WARNING
WE RECOMMEND THAT YOU NEVER SHUT DOWN THE MACHINE, even when closed for business, because
the automatic, timed functions help keep the colorant preserved and homogeneous.
Should it be essential to shut down the machine, avoid keeping it off for extended periods of time. When the
machine is not being used, if necessary shut off only the computer.
Very little power is used by the machine itself when inactive or during a stirring cycle.
1
0
2
COROB™ D600 - D700 - D800TX
- 30 -
USING THE DISPENSER
6 USING THE DISPENSER
6.1 General warnings
Personnel in charge of these operations must wear the following personal protective
equipment.
DANGER
The machine must be used by a single operator. Unauthorized people who could reach or touch machine parts
during operation must not be admitted in the nearby area.
It is strictly forbidden to use the machine without protections or with any safety devices present on the
machine disabled, broken down, or removed. The panels must be kept closed at all times.
Do not, for any reason, place your hands in the dispensing area when running the machine, except for loading
and unloading the cans.
When handling cans, do not exceed the weight limits stated by the current regulations in force (kg 20 for
women, kg 25 for men).
6.2 At the beginning of the working day
At the beginning of each work shift, always carry out the following operations:
• Check that the nozzle center is clean.
• (With humidier system for solvent-based colorants or without humidier system) Check that the sponge is
clean and saturated; if it is necessary to saturate, use only appropriate liquid (the choice of the liquid depends
on the nature of the colorants, and must be done directly by the manufacturer of the products used).
• (With humidier system for water-based colorants) Check that the water in the bottle is not below the
minimum level.
• Carry out system Initialization and Purge.
6.3 Running the machine
The operator is guided in running the machine by the management software, which displays the instructions to
be carried out and the actions performed by the machine.
Steps Options Reference
Make the selections from the management software
(selection of the product, formula and cansize).
Load the can in the machine and adjust the height of
the can shelf.
Adjust can position with respect to the dispensing
center.
Carry out punching of the can lid (optional). with punching device chapter 6.3.6
Via the software, enter the formula dispensing
command.
When dispensing is nished, remove the can and
proceed with another dispensing process.
with semiautomatic shelf chapter 6.3.1
with automatic shelf chapter 6.3.2
with panel roll conveyor chapter 6.3.3
with can centering device chapter 6.3.4
with Laser B.H.L. chapter 6.3.5
chapter 6.3.7
- 31 -
COROB™ D600 - D700 - D800TX
USING THE DISPENSER
6.3.1 Loading the can - Semiautomatic shelf
This button, when pressed with the safety button, causes the
Shelf UP button
shelf to rise and, when released, to stop immediately. If it is not
released, the shelf stops automatically when the can resting on it
is detected by the photocell.
Shelf DOWN button
SAFETY button, to enable
shelf movement
With the purpose to prevent any crushing risks, the semiautomatic shelf is tted with a lower safety
plate (chapter 3.5). The safety plate intervenes by causing the shelf to stop if it is inadvertently touched by the
operator.
1. Place the can on the shelf. Use the panel roll conveyors, if tted, to slide and ease heavy cans on the shelf
(chapter 6.3.3). Press and hold down the Safety and Up buttons to raise the shelf, which stops when the
can is correctly positioned.
2. If necessary, lower the shelf by means of the Safety and Down buttons.
This button, when pressed with the safety button, causes the shelf
to lower and, when released, to stop immediately.
This button, when pressed with the up or down button, enables
the shelf to move respectively up or down and, when released, to
stop immediately.
1 2
COROB™ D600 - D700 - D800TX
- 32 -
USING THE DISPENSER
6.3.2 Loading the can - Automatic shelf
With the purpose to prevent any crushing risks, the machine is tted with two safety plates (chapter 3.5.
The safety plates intervene by causing the shelf to stop if they are inadvertently touched by the operator.
1. Place the can on the shelf. Use the panel roll conveyors, if tted, to slide and ease heavy cans on the shelf
(chapter 6.3.3).
The management program controls the movement of the automatic shelf, checks for the can presence and that
the can placed on it is actually the one selected through the program for dispensing the formula.
These checks are also carried out by a photocell located underneath the nozzle center. The shelf automatically
stops when the can is detected by the photocell.
After a can has been positioned, the program will indicate an error if the can is missing from the shelf, or if it is
larger or smaller than the one selected for dispensing.
6.3.3 Loading the can - Panel roll conveyor
Place the can on the roll conveyor and slide it under the dispensing nozzles.
- 33 -
COROB™ D600 - D700 - D800TX
USING THE DISPENSER
6.3.4 Use of the can centering device
Place the can in the centering ring of the suitable diameter.
6.3.5 Use of the Bung Hole Locator
1. After having correctly positioned the can so as to obscure photocell A, the laser beams will switch on.
2. Position the can in such a way that the hole on the lid is in the center of the laser beams.
1 2
A
COROB™ D600 - D700 - D800TX
- 34 -
6.3.6 Punching the can
Shelf UP button
USING THE DISPENSER
When the punching lamp is on, pressing the three
Shelf DOWN button
SAFETY button, to enable shelf
movement
Punching lamp
Remember to carry out punching BEFORE commanding the dispensing from the software.
1. When the can has been positioned so as to obscure photocell A (chapter 6.3.1) the green lamp will light, to
indicate that is it is now possible to proceed with punching.
WARNING
Ensure that there is a lid on the can.
2. Press and hold down contemporaneously the Safety, Up and Down buttons; the shelf will rise further in
order to push the can against the puncher and then return to the initial position. During shelf descent, it is
possible to release the buttons.
buttons simultaneously will cause the shelf to be raised
to punch the can lid.
The green lamp on indicates that the machine is
ready to execute punching, since the can is correctly
positioned and obscures the photocell.
The blinking lamp indicates that an error has occurred
during punching.
- 35 -
COROB™ D600 - D700 - D800TX
USING THE DISPENSER
1 2
6.3.7 Dispensing
When the dispensing command is entered, the Autocap opens to expose the nozzles and the machine begins
to dispense the products included in the formula in the set amounts; the Autocap will automatically close when
dispensing is nished.
The dispensing time is the time required by the colorant of which the greatest amount is used in the formula.
6.4 Automatic processes
Colorant stirring is a timed process, activated automatically to properly store the product in the canisters
and keep it in ideal, homogeneous conditions for dispensing, through the movement of stirring paddles inside
canisters.
The recirculation process circulates the colorant through the dispensing circuits, avoiding pigment sedimentation
in the various parts of the circuit. The colorant leaves the bottom of the canister and returns in the canister
through the recirculation connector, without being dispensed through the nozzle center.
The duration and the interval between one stirring or recirculation cycle and another can be customized via the
conguration software, based on the nature of the products used on the machine.
We recommend to keep the canisters closed with their corresponding lids; do not insert hands in the
canister even when no colorant is present.
When an automatic process is in progress, the machine can still be used; the process will be suspended and
restarted after a few seconds that the machine is inactive.
COROB™ D600 - D700 - D800TX
- 36 -
6.5 Relling the canisters
USING THE DISPENSER
2
4
3
1.5 cm
0.6”
1. Press the emergency button (chapter 5.5).
2. Open the upper covers.
3. Remove the lid of the canister to be lled.
Shake the container of colorant to be poured into the canister manually. Do not use automatic shakers.
4. Add the desired colorant to the canister, so as to avoid spattering or creating air emulsions in the colorant.
WARNING
Never exceed the maximum colorant level in the canister, approximately 0.6” (1.5 cm) under the recirculation
connector. Never pour colorant directly onto the stirrer shaft.
5. Close the canister with its corresponding lid.
6. Repeat the above steps to ll other canisters.
7. Close the upper covers and restore the machine by releasing the emergency button (chapter 5.5).
8. Update the colorant level value for the topped up canisters in the machine management software (refer to
the software user’s manual).
- 37 -
COROB™ D600 - D700 - D800TX
USING THE DISPENSER
WARNING
In case of improper actions, which caused canister overlling with colorant:
• In case the colorant has poured inside the machine, do not try to clean; turn the machine off at once and
contact an authorized service center.
• If, on the contrary, the product has already poured out of the canister, it is necessary to shut off the
machine immediately and clean with paper or a moistened cloth. Whenever possible, leave the colorant to
dry itself and remove with a spatula.
• If the product has not yet come out of the canister borders, it is necessary to avoid closing the canister with
its lid and provide immediately to dispense the exceeding colorant until the correct level is reached. Clean
carefully the upper border of the canister with paper or a moistened cloth before closing it with the lid.
NEVER USE WATER OR SOLVENT-BASED CLEANING PRODUCTS TO CLEAN THE MACHINE.
DANGER
When using colorants containing volatile solvents the canister top up must be carried out opening one
canister at the time.
WARNING
Failure to update the colorant levels in the canisters may compromise the accuracy of the hue produced or,
worse yet, lead to emptying the machine canisters and circuits.
If “SOLVENT FREE” colorants are used, or those that dry out quickly, we recommend that you keep the
canisters full at all times by topping up frequently.
After topping up the colorant, it is advisable to carry out the stirring process using the functions provided in the
management software, to eliminate any air that may be emulsied and incorporated into the colorant.
COROB™ D600 - D700 - D800TX
- 38 -
6.6 Troubleshooting
Problem Cause Solution
Check the connections at the back of the
machine (chapter 5.3).
Set the main switch to the ON position (I)
(chapter 5.3).
Replace any blown fuse inside the fuse
compartment (chapter 5.2).
Wait a few minutes and try to restart the
machine. If the problem persists, contact the
authorized technical service.
Contact the authorized technical service.
Turn the machine on (chapter 5.3) and
restart the management software.
Check the connections at the back of the
machine (chapter 5.3).
Use the conguration and calibration
software to make sure you have correctly
congured the port used to communicate
with the machine.
Repair the computer serial port or USB port.
Replace the communication cable using
manufacturer’s original spare parts.
Move the semiautomatic shelf down (chapter
6.3.1) until the photocell is no longer covered
by the can, the green punching lamp will
stop blinking; load a can with lid then repeat
the punching operation.
The machine does not turn
on.
The management software
shows an error in the
communication protocol.
Power supply is missing.
Main switch in OFF position (O).
Emergency button is pressed. Release the emergency button (chapter 5.5).
One or more fuses may be blown
up.
The power supply unit is in
overcurrent.
Electrical connections are
defective.
Machine is OFF.
Machine disconnected from the
computer.
Computer serial port or USB port
wrongly congured or defective.
Serial cable damaged.
Connection defective. Contact the authorized technical service.
The operator released one of the
buttons, thus interrupting the
punching operation.
Punching has failed because the
can lid was missing.
USING THE DISPENSER
The green punching lamp
blinks.
Due to a mechanical problem the
punching device did not return to
its initial position.
DANGER OF CUTS.
YOU MUST WEAR CUT-PROOF GLOVES.
Grasp the punching group and bring it back
to the initial position, the green punching
lamp will stop blinking; repeat the punching
operation. If the problem persists, contact
the authorized technical service.
- 39 -
COROB™ D600 - D700 - D800TX
ORDINARY MAINTENANCE
COROB™ D600 - D700 - D800TX
- 40 -
ORDINARY MAINTENANCE
7 ORDINARY MAINTENANCE
7.1 General warnings
Personnel in charge of these operations must wear the following personal protective
equipment.
DANGER
Before carrying out any maintenance operations, you must turn off the machine and unplug the power supply
cable from the mains socket outlet.
During machine maintenance operations there is a high risk of contact with the coloring product; strictly follow
the indications of chapter 3.2.
7.2 Maintenance table
WARNING
The frequencies indicated are approximate, since they depend on the type of colorants, environment conditions
and frequency of use of the machine.
Frequency
Operations Accessories
Initialize and purge machine
Clean the nozzle center
Check the sponge is clean
Check the sponge is saturated
Moisten the sponge
Clean the sponge
Check condition of puncher with punching device
Clean the dispenser externally
Fill up the humidier system bottle
with humidier system for solvent-based
colorants or without humidier system
with humidier system for solvent-based
colorants or without humidier system
with humidier system for water-based
colorants
beginning
of shift
twice a
week
when
necessary
7.3 Products to be used
We recommend to use products compatible with the type of colorants in the machine when cleaning the nozzle
center and moistening the humidier cap sponge.
Type of colorant Suggested product
Solvent-based colorants slow-evaporating solvent, compatible with the colorants used
Water-based colorants water
Mixed systems
Should growths form in the Autocap, in the sponges or in the humidier system water bottle, it is advisable to
use the following uids:
• Propylene glycol solution, 50% by volume, in water;
• AgCl solution in water;
• Bleach (dilution 1%).
the choice depends on the type of vehicles used to produce the colorants; for
more information, contact the dealer or colorant manufacturer.
- 41 -
COROB™ D600 - D700 - D800TX
ORDINARY MAINTENANCE
7.4 External cleaning
WARNING
NEVER USE WATER OR SOLVENT-BASED CLEANING PRODUCTS TO CLEAN THE MACHINE.
In case the colorant has poured inside the machine, do not try to clean; turn the machine off at once and
contact an authorized service center.
In case of paint spills, clean the machine immediately.
1. Disconnect power supply (chapter 5.6).
2. Clean coverings, panels and control devices of the
machine, to remove dirt, dust and any colorant
stains, using a soft and dry cloth, or slightly
moistened with a mild cleansing solution.
3. Connect power supply and switch on the machine
(chapter 5.3).
See the manufacturer manual for instructions on
cleaning the computer.
7.5 Cleaning the nozzle center
1. Open the Autocap using the command in the
management software.
2. Disconnect power supply (chapter 5.6).
3. Accurately clean the nozzles using a sharp tool;
remove any dried colorant residue delicately, to
avoid damaging the ends of the circuits.
4. Connect power supply and switch on the machine
(chapter 5.3); the Autocap closes automatically
during initialization.
5. Carry out Purge, using the command in the
management software.
COROB™ D600 - D700 - D800TX
- 42 -
ORDINARY MAINTENANCE
7.6 Cleaning and moistening the humidier cap sponge
In case of sponge replacement, use only those supplied with the machine.
8 mm To remove the Autocap screw(s)
DANGER
IF THE MACHINE IS EQUIPPED WITH PUNCHING DEVICE, YOU MUST WEAR CUT-PROOF GLOVES.
1. Open the Autocap using the command in the management software.
2. Disconnect power supply (chapter 5.6).
3. If present, open the inspection door in the dispensing area.
4. Loosen screw A (if present) and remove the sponge support B by turning it counter-clockwise.
A
WITHOUT HUMIDIFIER SYSTEM WITH SOLVENT HUMIDIFIER
SYSTEM
a. Check the condition of the
sponge and moisten as needed.
The level of the humidifying
liquid must not exceed the
height of the sponge. If it is very
dirty, remove the sponge from
the cap and wash it thoroughly.
b. Check the condition of the
sponge. If it is very dirty, remove
the sponge from the cap and
wash it thoroughly. Top up with
a small quantity of solvent the
tank inside the sponge support;
when repositioning the sponge
on the lter, be careful to dip
the tail into the solvent.
B
WITH WATER HUMIDIFIER
SYSTEM
c. Check the condition of the
sponge. If it is very dirty,
remove the sponge from the
cap and wash it thoroughly.
- 43 -
COROB™ D600 - D700 - D800TX
ORDINARY MAINTENANCE
a b
5. In all cases, if the sponge is severely damaged, replace it.
6. Fit back the sponge support.
7. Connect power supply and switch on the machine (chapter 5.3); the Autocap closes automatically during
initialization.
COROB™ D600 - D700 - D800TX
- 44 -
7.7 Checking and replacing the puncher
DANGER
TO PERFORM THIS OPERATION YOU MUST WEAR CUT-PROOF GLOVES.
8 mm
To remove the puncher
2 3
B
ORDINARY MAINTENANCE
A
4
Dx2
A+BA+B
C
1. Disconnect power supply (chapter 5.6).
2. Screw tool A to puncher B.
3. Insert wrench C in the tool slots and slightly loosen screws D (do not unscrew them completely).
- 45 -
COROB™ D600 - D700 - D800TX
ORDINARY MAINTENANCE
4. Rotate and pull down tool A, so as to remove puncher B, then separate the puncher from the tool.
5. If necessary, clean the surfaces of the puncher to remove encrusted matter, using a product compatible with
the type of bases used in your system. We recommend lubricating the puncher walls with a common, noncontaminant lubricant (ENOTAP or similar).
6. Reassemble the puncher following the above steps in reverse order.
7. Connect power supply and switch on the machine (chapter 5.3).
If the can punching is inadequate because the cutting edge of the puncher is excessively worn, replace the worn
puncher.
7.8 Relling the humidier system bottle
WARNING
When the water in the bottle reaches the minimum level, ll up immediately.
1. Disconnect power supply (chapter 5.6).
2. Open the machine upper cover where the bottle is located.
3. Unscrew the bottle cap and add water (1 Pint / 0.5 liters maximum), paying attention NOT TO EXCEED THE
MAXIMUM LEVEL.
To reduce the risk of lime encrustations due to hard water, it is recommended to use distilled water.
4. Replace the cap and rmly tighten.
5. Close the upper cover, connect power supply and switch on the machine (chapter 5.3).
2 3
5
0
0
1
P
m
i
n
l
t
MAX
MIN
MAXMAX
MIN
MIN
COROB™ D600 - D700 - D800TX
- 46 -
TECHNICAL SPECIFICATIONS
8 TECHNICAL SPECIFICATIONS
8.1 Technical data
D600 TE D600 TI D700 D800TX
Single-phase 220 - 240 V ~ ± 10%
Power supply
Frequency 50/60 Hz
Fuses* F 10 A
Maximum power absorbed* 650 W
Noise level Level of equivalent acoustic pressure: < 70 dB (A)
Environment working
conditions**
Vibrations
The machine does not transmit vibrations to the oor that may compromise
Temperature: between 10°C (50°F) and 40°C (104°F)
Relative humidity: between 5% and 85%, without condensation
the stability and precision of any nearby equipment.
Dispensing technology gear pump
Dispensing system simultaneous
Dispensing center External Internal \ External
Type of canisters all-purpose (POM acetalic resin)
Type of valves electrovalves
Machine
***
Packed machine
* Not including connected auxiliary devices. The power information is purely indicative, and depends strictly on the machine conguration.
** The environment working conditions are strictly related to the type of colorants used (ask for information from the paint manufacturer). The
data shown are valid for the machine only.
*** Data refer to the machine with empty canisters and without accessories.
639 lb (290 kg) (16)
772 lb (350 kg) (24)
728 lb (330 kg) (16)
882 lb (400 kg) (24)
Single-phase 100 - 110 V ~ ± 10%
Other power supplies available upon request
650 W (up to 24 circuits)
800 W (from 25 to 32 circuits)
661 lb (300 kg) (16)
904 lb (410 kg) (32)
750 lb (340 kg) (16)
992 lb (450 kg) (32)
Standard circuit LAB circuit HF circuit
Flow rate (theoretical at 100 rpm) 0.5 l/min 0.161 l/min 0.952 l/min
Minimum dispensed quantity****
1/384 US oz
(0.077 ml)
1/1152 US oz
(0.026 ml)
1/192 US oz
(0.154 ml)
Theoretical resolution**** 0.00214 cc/step 0.000713 cc/step 0.00428 cc/step
**** Values highly affected by the nature of the colorants and their rheological properties.
- 47 -
COROB™ D600 - D700 - D800TX
TECHNICAL SPECIFICATIONS
8.2 Dimensions
* Data are indicative and depend on machine conguration.
D600 TI
1070 mm
42.1”
340 mm
13.4”
D600 TE
15.6”
397 mm
355 mm
440 mm
14”
VL 876 mm - 34.5”
17.3”
1070 mm
42.1”
410 mm
16.1”
VP 898 mm - 35.4”
43.6”
1108 mm
VL 876 mm - 34.5”
VP 898 mm - 35.4”
18.5”
426 mm
16.8”
366 mm
14.4”
302 mm
11.9”
470 mm
1190 mm
1190 mm
46.9”
46.9”
D700
19.7”
509 mm
355 mm
1236 mm
48.7”
43.6”
1108 mm
14”
574 mm
22.6”
470 mm
18.5”
426 mm
16.8”
366 mm
14.4”
302 mm
11.9”
1190 mm
46.9”
COROB™ D600 - D700 - D800TX
- 48 -
D800TX
16.8”
17.2”
427 mm
437 mm
1400 mm
55.1”
TECHNICAL SPECIFICATIONS
46.9”
1010 mm - 39.8 ”
1270 mm - 50”
18.5”
16.8”
470 mm
426 mm
366 mm
14.4”
1190 mm
574 mm
22.6”
D600 TI / D600 TE D700
414 mm
16.3”
28.3”
720 mm
130 mm
5.1”
ADDITIONAL MODULE
330 mm
13”
D800TX
578 mm
22.8”
320 mm
12.6”
394 mm
15.5”
579 mm
22.8”
480 mm
18.9”
410 mm
16.1”
720 mm
28.3”
130 mm
5.1”
391 mm
15.4”
39”
991 mm
- 49 -
46.9”
1190 mm
COROB™ D600 - D700 - D800TX
46.9”
1190 mm
TECHNICAL SPECIFICATIONS
8.3 Declaration of conformity
See Declaration of conformity attached.
8.4 Warranty
In order for the warranty to be valid, please complete the form included in the machine packing, and send it to
the address listed on the form itself.
Contact our authorized and qualied personnel only for all your service needs. Use only original spare
parts for all maintenance and replacement interventions.
Altering or removing the guards and safety devices provided on the machine will not only void the warranty
immediately, but is also dangerous and illegal.
The manufacturer may not be held liable for personal injury or property damage caused by improper use of the
equipment or tampering with the guards and safety devices installed on the machine.
The following shall void the manufacturer’s warranty:
• Improper use of the machine.
• Failure to observe the instructions and maintenance rules set forth in the manual.
• Making or having changes and/or repairs made on the machine by personnel outside the service organization
authorized by the manufacturer and/or made using non-original spare parts.
COROB™ D600 - D700 - D800TX
- 50 -
Loading...