CORNING ONE OIU Quick Installation Sheet

Optical Interface Unit (OIU)
Quick Installation Sheet

CMA-263-AEN

GENERAL INFORMATION

• OIMe —optical module only; ber jumper is not included —
compatible MTP®-LC APC harness cable is ordered separately
(see Section 2 of this document)

• OIU chassis is supplied empty and only includes the factory-assembled
fan module (FAM). All other modules (i.e., power supplies, controller,
OIMe, OIXs, and FMMs) are ordered separately and must be installed.

This document describes the installation and connection procedures for the Corning® optical network evolution (ONE™)
solutions optical interface unit (OIU) and relevant modules.

Note: The instructions for installing and connecting ber main modules (FMMs) in the OIU chassis are not in the scope of this
document. For details, refer to the quick installation sheet provided with the module.

. REQUIRED KITS

The following kits are required for installing the OIU. If any of the listed items are missing, contact your Corning
representative.

OIU Kit Qty Item

OIU Chassis (with blank panels) —
with factory-assembled FAM and rack brackets

Fan Module (FAM) — one unit hosting four fans
(factory installed in chassis rear)

RJ45 100 Base-T Ethernet Communication Cable,
L = 2-2.15 m (P/N: 705900003) — ACM management
connection

1

2

1

Table 1. Kits Required for OIU Installation

Corning Optical Communications

Quick Installation Sheet | CMA-263-AEN | Page 1

. REQUIRED KITS (CONTINUED)

OIM Kit (1-12 according to order) Qty Item

Optical Interface Module 1

PSM Kit (AC or DC modules —

Qty Item

1 or 2 kits according to order)

PSM-AC: 100-240 VAC Power Supply Module including

1

standard IEC 60320-1 C13 cable

PSM-DC: 48 V DC Power Supply Module; 9 A maximum.;
Includes six-pin terminal block connector

OIX Kit (1 or 2 according to order) Qty Item

Optical Interface Expander Module —provides RF

1

interface to headend unit (HEU)

ETM Kit Qty Item

Expander Termination Module — provides termination

1

for unused expander slot

ACM Kit Qty Item

Auxiliary Control Module — provides interface to

1
headend control module (HCM) for remote management
and enables local management of unit

Table 1. Kits Required for OIU Installation (continued)

Corning Optical Communications

Quick Installation Sheet | CMA-263-AEN | Page 2

. ADDITIONAL REQUIRED ITEMS (NOT PROVIDED)

. MTP®-LC APC harness cable (P/N: 37HP900162-006F) — consists of connector

for splitting bers (six) leading from OIM to ber management unit (FMU)
EDGE™ module

2. Four rack-mount nuts and screws for securing unit in rack

3. Grounding tools and components:

• Grounding wire — grounding wire should be sized according to local and

Harness Cable

national installation requirements. The provided grounding lug supports
14 AWG to 10 AWG stranded copper (or 12 AWG to 10 AWG solid) wire conductors.

Note: The length of the grounding wire depends on the proximity of the switch to proper grounding facilities.

• Phillips-head screwdriver

• Crimping tool — for crimping grounding wire to the grounding lug.

• Wire-stripping tool — for removal of insulation from wire

. INSTALL UNIT IN -IN RACK

Notes: Up to four OIU chassis can be connected to a

single HEU

OIU chassis requires 4U rack height availability

Step 1: Determine the location of the OIU in the rack

while considering additional HEUs and OIUs and
the lengths of the ERFCs (described in HEU quick
installation sheet).

Figure 1 and Figure 2 describe the optimal rack

installations for 4x4 HEU-OIU congurations in
shared and dedicated equipment scenarios.

Step 2: Referring to Figure 3, secure the units’ rack ears

to the rack frame as follows:

• Insert two screws halfway into the rack frame.

• Position the chassis on to the screws using the
handles and the top and bottom half slots of
the rack ears.

• Secure the unit in the rack via all applicable
bracket holes using the appropriate rack nuts
and screws.

Figure 1. 4x4 Rack Installation Diagram – Dedicated

Figure 2. 4x4 Rack Installation Diagram – Shared

Corning Optical Communications

Figure 3. Positioning Chassis in Rack

Quick Installation Sheet | CMA-263-AEN | Page 3

. INSTALL ALL MODULES

Note: For modules with ejectors (i.e., OIM, OIX, and ACM)

– verify that the ejectors are completely open when
inserting in dedicated slot and then push in until
the module clicks in to the backplane. Figure 4
shows example of module type captive screws and
ejectors.

Step 1: Refer to Figure 5 for module locations. Remove

blank panel and slide in the relevant module
(chassis slots are 100 percent mistake proof):

• (One) ACM

• (One to two) PSM – for single-power supply
installations, install the PSM in either (PSM) slot.

• (One to two) OIX – for single OIX installations,
the second OIX slot must be occupied with an
expander termination module (ETM).

• (One to 12) OIM — no need to terminate
unoccupied OIM slot.

Step 2: Secure modules into the OIU backplane by:

Figure 4.Module Ejectors

• Closing ejectors rmly (for relevant modules)

• Tightening the captive screws

. GROUND CHASSIS

The grounding connection is performed via a two-hole, standard

barrel grounding lug located on the chassis rear panel (see Figure 6).

Prise de terre du châssis OIU:

La mise à la terre est réalisée en utilisant une cosse deux trous a

œillet standard, située à l’arriè du chassis OIU (voir Figure 6).

Figure 5. Location of OIU Chassis Modules

Figure 6. Location of Chassis Grounding Lug

Corning Optical Communications

Quick Installation Sheet | CMA-263-AEN | Page 4

. GROUND CHASSIS (CONTINUED)

Step 1: Use a wire-stripping tool to remove approximately

0.4- in (10.9 mm) of the covering from the end of
the grounding wire.

Step 2: Insert the stripped end of the grounding wire into

the open end of the grounding lug.

Step 3: Crimp the grounding wire in the barrel of the

grounding lug. Verify that the ground wire is
securely attached to the ground lug by holding the
ground lug and gently pulling on the ground wire.

Step 4: Prepare the other end of the grounding wire and

connect it to an appropriate grounding point at the
site to ensure adequate earth ground.

. FIBER CONNECTIONS

Using an MTP®-LC APC harness cable:

• Connect the harness cables’ MTP® connector to the
OIM MTP connector

• Remove the protective plastic covers and connect the
(3) LC APC connection bers to the FMU EDGE™ module
LC APC connections. See Figure 7.

ATTENTION! Take note of the ber numbering (i.e., 1/2/3).

. EXPANDER CONNECTIONS TO HEU

RF expander connections between the OIU and HEU are

performed using the ERFC cable (included in HEU order)
and are described in the HEU quick installation sheet
(CMA-267-AEN) provided with the unit. See Figure 8 for
general view of connections.

Figure 7. OIMs Fiber Connections

Figure 8. OIX-to-RIX Expander Connection

Corning Optical Communications

Quick Installation Sheet | CMA-263-AEN | Page 5

. POWER UP

Note: Only AC power connections are decsribed in this document. Refer to PSM-DC quick

installation sheet (CMA-365-AEN) provided with PSM-DC for wiring pinout.

Figure 9. PSM-AC
Interfaces

ATTENTION!

• Approved power cable – the entire length of the
power cable (or exible cord) and the insulation must
be intact. The cable must be rmly connected to both
the electrical plug and the unit itself.

• Standard plug – the use of a standard plug is
mandatory. The use of a non-standard power plug can
cause electrocution! Also, plugging a non-standard
plug into a standard socket that does not correspond
to the plugs’ shape, can damage the socket making it
a safety hazard.

• Always disconnect all AC power sources from the unit
before servicing (i.e., maintenance).

To power up the unit:

Connect the PSM-AC power connector to the AC power
source using the provided AC power cable and turn
power switch on. See Figure 9 for AC connector location.

• Power input: 100-240 VAC

• Power consumption (fully loaded chassis):
300 W (maximum);

ATTENTION!

• Câble d’alimentation qui est approuvé —la totalité
de la longueur du câble d’alimentation (ou cordon
souple) et de l’isolation doit être intact. Le câble doit
être bien connecté à la fois à la prise électrique et
l’appareil.

• Prise électrique standard — l’utilisation d’une
che standard est obligatoire. L’utilisation d’un
cordon d’alimentation non standard peut entraîner
l’électrocution! De meme, brancher une che non­standard sur une prise standard ne correspondant
pas à la forme de de la che, peut endommager la
Prise, ce qui en fait un danger de sécurité.

• Débrancher toujours toutes les sources
d’alimentation CA de l’unité avant l’entretien.

Pour mettre l’unité sous tension:

Branchez la prise d’alimentation du PSM-AC à la source
d’alimentation secteur à l’aide du câble d’alimentation
secteur fourni et allumer l’interrupteur. Voir Figure 9
pour l’emplacement du connecteur AC.

• Alimentation: 100-240 VAC

Corning Optical Communications

• Consommation maximale électrique
(pour les châssis entièrement charges):
300 W ; 18 W par OIM

Quick Installation Sheet | CMA-263-AEN | Page 6

. MANAGEMENT CONNECTIONS

Using the provided RJ45/RJ45 communication cable connect

the OIU ACM control module as follows:

• Referring to Figure 10 — for congurations with one
HCM and up to four ACMs (e.g., one HEU and four OIUs),
directly connect as follows:

From any …. To any ….

ACM “INTERNAL
(TO HCM)” port

HCM “INTERNAL
(TO ACM)” port

• For congurations with one HCM and more than four
ACMs (e.g. , 4x4 HEU-OIU congurations) where there
are only four available HCM “INTERNAL” ports:

From any …. To any ….

ACM”INTERNAL
(TO ACM)” port

Other available ACM
module “INTERNAL
(TO ACM)” port

Refer to Figure 11 for schematic example of management

connections.

Note: Main HEU refers to HEU with HCM.

Figure 10. Direct OIU Management Connection

Figure 11. Schematic Example of 4x4 Management
Connections

Corning Optical Communications

Quick Installation Sheet | CMA-263-AEN | Page 7

. VERIFY NORMAL OPERATION

If OIU chassis is powered on, verify that the OIM and ACM (see Figure 12) module LEDs indicate normal operation:

Figure 12. OIM and ACM Status LEDs

Module LED Description

PSM PWR Status Green steady — power input detected

Off — no power

OIM LINK 1/2/3 Steady green — optical link power to/from the connected remote is normal

Off – no optical power from remote detected

RUN Blinking green — OIM software has initialized and is up and running

Off — power off

PWR Steady green — power input detected in OIMe

ACM PWR Steady green — power input detected by ACM

RUN Blinking green — ACM software up and running

SYS Steady green — overall status of the managed system OK

FAN Steady green — normal operation status for all fans

Table 2. OIMe and ACM Status LED Descriptions

Corning Optical Communications LLC • PO Box 489 • Hickory, NC 28603-0489 USA
800-743-2675 • FAX: [phone] • International: [phone] • www.corning.com/opcomm

Corning Optical Communications reserves the right to improve, enhance, and modify the features and specifications of Corning Optical Communications products without prior notification. A complete listing of
the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are the properties of their respective owners. Corning Optical Communications is
ISO 9001 certified. © 2013, 2018 Corning Optical Communications. All rights reserved. CMA-263-AEN / March 2018

P/N 709C021301 A00