Page 1
IDC 255 Icemaker Adaptor Kit Installation Instructions
!
WARNING:
!
WARNING:
Icemaker Adaptor Kit
Bar
Cross Braces
INSTALLATION INSTRUCTIONS
IDC 255 ICEMAKER ADAPTOR KIT FOR P/N 629088756
(
FOR HOSHIZAKI KITS)
Disconnect power to the unit before installing adaptor following all lock out / tag out procedures established by the
user. Verify all of the power is off to the unit before performing any work. Failure to comply could result in serious
injury, death or damage to the equipment.
All of the attachment screws and plates must be installed as directed in this manual. Failure to comply could result in
serious Injury, Death or Damage to the equipment.
FIGURE 1
Revision Date: August 3, 2010 www.cornelius.com Revision: B
© 2006-2010, IMI Cornelius Inc. - 1 - Publication Number: 629088756INS
Page 2
IDC 255 Icemaker Adaptor Kit Installation Instructions
Cross
Braces
Front Icemaker
Rail Support
3.096
1. Place bar into first set of pockets inside the ice bin.
FIGURE 2
2. Place Icemaker rail supports into pockets in the ice bin as shown in Figure 2.
3. Hook cross braces over top of bar and place into outer pockets inside the ice bin (at back end).
4. Place the icemaker adaptor kit on top of unit.
5. Place the icemaker on top of kit and adjust it so that only 3.096” of it protrude outside the IDC
wrapper, as shown in (Figure 3). DO NOT slide icemaker into position on the lid.
6. Apply a continuous bead of NSF International (NSF) listed silastic sealant (Dow 732 or equivalent),
supplied in kit to seal the icemaker to the top of the adapter kit. All excess sealant must be wiped
away immediately.
Publication Number: 629088756INS - 2 - © 2006-2010, IMI Cornelius Inc.
FIGURE 3
Page 3
IDC 255 Icemaker Adaptor Kit Installation Instructions
MOUNTING OPTION 1
(FLAT BRACKETS)
MOUNTING OPTION 2
(ANGLE BRACKETS)
7. The next steps discuss loading and securing the icemaker onto the kit. Please read all the following
steps to determine which mounting method should be utilized. Equally important is to determine if
there is sufficient access in the area of the mounting brackets after the dispenser is lifted onto the
counter. Access should be carefully considered before installation continues because sufficient
room is required for drilling holes, installing screws, etc.
Two options are supplied with this kit for securing the icemaker to the kit. (See Figure 4)
Option 1: Includes two flat brackets. This method may be used if there is sufficient access to the
back of the dispenser in the areas of the mounting brackets.
Option 2: Includes two angle brackets. This method may be used if there is not sufficient access to
the back of the dispenser in the areas of the mounting brackets. Pre-drilling holes should be
considered when using this option.
8. The next step is to secure the icemaker to the kit. Depending on the mounting method chosen, use
the appropriate brackets (supplied) as templates to drill four 9/64” (.140” Dia.) holes into the back
side of the adapter kit. Drill four holes of the same diameter into the icemaker (Figure 4). Ensure the
location of the brackets will not damage the kit or the icemaker prior to drilling any holes. USE
EXTREME CAUTION NOT TO DRILL INTO ANY OTHER COMPONENTS. Drill depths should not
go further than the thickness of the material being drilled (just enough to go through). Secure the
two brackets using the screws provided.
9. For optimal performance, do not fill ice bin more than 2/3 capacity (maximum fill is 4” below top of
bin). Applies to IDC 255 models and nugget ice only.
NOTE: Adaptor kits are only approved for top mounting a single icemaker.
© 2006-2010, IMI Cornelius Inc. - 3 - Publication Number: 629088756INS
FIGURE 4
Loading...