Cornelius 430, 830, 530, 630 User Manual

ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ED/DF300 30” CCM330/430/530/630/830/1030 NORDIC BLACK/GRAY
S

TYLE LID KITS

This Nordic style kit applies to the Cornelius 30” wide CCM330/430/530/630/830/1030 ice maker.

Item

No.

1 15209 Adapter Lid 1

2 22127 Bracket 2

3 50904 RTV 1

4 52946

5 91957 Label 1

6 620042919 Baffle, Ice 1

7 70226 #10 x 3/4” Sheetmetal Screw 12

8 620701902 Acorn Nut, 8--32 Nylon 4

9 620701901 Sealing Washer 4

10 611701903 #8 Nylon Washer 4

11 15192 Lid Opening Cover (For 22–inch Wide

12 630500109 Bin Stat 1

CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker
adapter kit installation.

WARNING: The dispenser must be secured with 3/8-16 bolts (6) to the counter before installing
this Icemaker Adapter Kit. Refer to the installation manual and Figure 2 for the counter mounting
template.

Part No. Name Qty.

Cover, Gray

52964

Cover, Black

Icemakers)

1

2

NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5
seconds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper
front panel.

1. Unpack kit.

2. Remove the two (2) screws from each side of the dispenser cabinet and the plastic hopper covers
(2) that were shipped with the unit.

3. Place the Adapter lid on the unit and use the four (4) screws that were removed to fasten the lid in
place.

4. Install the ice baffle on the lid assembly as shown in Figure 2.

IMPORTANT: The baffle prevents ice from over–filling the manual fill area during agitation/
dispensing with a full storage bin and forcing the manual fill cover off.

5. Seal the ice maker to the top of the dispenser after determining the correct location for the ice
maker (see Figure 1).
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the ice maker

outline so that the ice maker will set on the RTV.

B. Set the ice maker onto the lid and position it as required.
C. Wipe away the excess RTV.

6. Drill .136 diameter holes into the ice maker cabinet and the dispenser lid using the ice maker
mounting brackets as templates. USE CAUTION SO AS NOT TO DRILL INTO ANY ICE MAKER
COMPONENTS (CONDENSER, TUBING, ETC.). Secure the brackets using the #10 sheet metal

Release Date: October 5, 2007 www.cornelius.com Revision: A
© 2007, IMI Cornelius Inc. - 1 - Publication Number: 620204732INS

screws provided.

ED/DF300 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions

7. Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of
the wireform bracket and wrap the tube around the end of the bracket several times, insuring the
tube is secure.

NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from
the icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.

8. For 22–inch wide Icemakers, locate the lid opening covers (2) item 11 as shown in Figure 1. Secure
the covers to the adapter lid by drilling .136 diameter holes into the lid. Use the covers as templates
to locate the mounting holes. Secure the covers with the # 10 sheet metal screws.

9. Locate the cleaning caution label (item 5) on the manual ice fill cover (item 4) as shown in Figure 1.
Place the manual fill cover in position over the flange on the lid assembly and the front access
hopper opening.

10. The unit is now ready for operation.

SEAL ICE MAKER TO

ITEM 1 WITH ITEM 3

2

11

5

7

7

11

4

3

REFER TO

STEP 4

1

NOTE: BACK OF ICEMAKER

MUST BE FLUSH WITH THE

BACK OF LID

Use the four existing 8-32 3/8

screws (P/N 70171)

ICEMAKER LOCATION

30”

22”

“A”

ICEMAKER

SIZE

LOCATING

7-1/4”

11-1/4
”

“B”

DIM.

FIGURE 1. ED/DF300 Kit

Publication Number: 620204732INS - 2 - © 2007, IMI Cornelius Inc.