Copyright
This document, as well as the software described in it, is furnished under
license and may be used or copied only in accordance with the terms of
the license. The content of this document is furnished for informational
use only, it is subject to change without notice, and it does not represent a
commitment on the part of Corinex Communications Corp.
Corinex Communications Corp. assumes no responsibility or liability for
any errors or inaccuracies that may appear in this document.
It is our policy to enhance our products as new technologies, hardware
components, software and firmware become available; therefore, the
information contained in this document is subject to change without
notice.
Some features, functions, and operations described in this document
may not be included and sold in certain countries due to government
regulations or marketing policies.
The use of the product or its features described in this document may be
restricted or regulated by law in some countries. If you are unsure which
restrictions or regulations apply, you should consult your regional Corinex
office or the authorized reseller.
1
Published by:
Corinex Communications Corp.
World Trade Center
404-999 Canada Place
Vancouver, B.C.
Canada V6C 3E2
Tel.: +1 604 692 0520
Fax: +1 604 694 0061
Corinex is a registered trademark of Corinex Communications Corp.
Apple, MAC OS X are either registered trademarks or trademarks of Apple
Computer, Inc. in the U.S.A. and/or other countries.
Microsoft, MS-DOS, MS, Windows are either registered trademarks or
trademarks of Microsoft Corporation in the U.S.A. and/or other countries.
All products or company names mentioned herein may be the trademarks of
their respective owners.
Copyright (c) 2001-2003 by Corinex Communications Corp.
2003-11-13 ver 1.2
Corinex Wireless to Powerline AP
Content
Package Content ....................................................................... 3
Requirements ............................................................................. 4
Installation Overview ................................................................. 4
Step 1: Connecting the Access Point .....................
Step 2: Configuring Computers ................................................. 6
Step 3: Configuring the Access Point ....................................... 10
....................
Content
5
2
Corinex Wireless to Powerline AP
Package Content
Wireless to powerline local area network (LAN) solutions, based on Corinex
Wireless to Powerline Access Point (AP) products, connect a wireless
device to the electrical wires in premises. The electrical wires build the
"backbone" for other "wired" or "wireless" devices on the network, which
are connected to this backbone by Corinex Powerline adapters or another
wireless to powerline access point. Any high-performance Corinex Wireless
to Powerline AP extends the coverage of your network of electrical wires
and provides access to the Internet and corporate or personal information
for all mobile devices without expensive additional cabling infrastructure.
The
Corinex Wireless to Powerline Access Point is a Powerline to wireless
LAN Bridge for mixed wireless 802.11b and Powerline network environment.
With the built-in 802.11b capability, you can connect your legacy wireless
device to the home network by plugging the Corinex Wireless to Powerline
Access Point into your power plug.
The AP's power jack is a connecting medium to the 14 Mbps digital
powerline communication network based on the HomePlug 1.0.1 standard.
Plug the Corinex Wireless to Powerline AP into an existing powerline
network and instantly add full 802.11b-compliant wireless connectivity
at up to 11 Mbps. This allows the easiest deployment of wireless HotSpot
areas where every power outlet can be used as a powerline network
interface to the access point. With Corinex Wireless to Powerline AP you
have already got the network you need to give the wireless access an
entirely new dimension.
3
Package Content
Package Includes:
By receiving your Corinex Wireless to Powerline Access Point, check to be
sure that your package contains:
• Corinex Wireless to Powerline Access Point
• Detachable wireless antenna
• AC adapter
• Installation CD-ROM with User Guide
• Quick Installation Guide
Corinex Wireless to Powerline AP
Requirements/Installation Overview
Requirements
• IBM Compatible PC or Macintosh computer (needed for initial
configuration of the Access Point)
• AC 220/110 V power outlet
• Powerline and/or Wireless connection for each PC
• Windows 98/ME/200/NT/XP, Mac OS X or Linux operating system
• Web browser supporting JavaScript for the AP management
Installation Overview
This Guide will assist you with successful installation and configuration of
your Corinex Wireless to Powerline Access Point for the first time. It will
help you with basic settings, which are covering most of the settings you
may need to configure for your Internet connection to be shared through
the Powerline medium. However, if you require more sophisticated setup,
we advise you to read the Corinex Wireless to Powerline Access Point User
Guide, enclosed in the Installation CD.
4
The next chapters will explain you how to connect your Corinex Wireless to
Powerline Access Point in three easy steps.
Corinex Wireless to Powerline AP
Step 1: Connecting the Access Point
Step 1: Connecting the Access Point
Locate an optimum location for the Access Point. The best place for the
Access Point is usually at the center of your wireless network, with line of
sight to all of your mobile stations.
Fix the direction of the antenna. Try to place it in a position which can
best cover your wireless network.
the Corinex Wireless to Powerline Access Point and consequently into an
AC outlet. Use only the power adapter supplied with the Access Point.
Usage of a different adapter may result in product damage!
After the Corinex Wireless to Powerline Access Point is powered ON, verify
LED functionality below:
• The LED on the Powerline side labelled LINK should be ON
• The LED on the Wireless side labelled POWER should be ON
Note: All other wireless devices must be operating in the infrastructure
mode, so that they can communicate with Access Point. If any wireless
device is configured in the ad-hoc mode, it WILL NOT be recognized by
the Access Point.
Plug the supplied AC power adapter to
5
Corinex Wireless to Powerline AP
Step 2: Configuring Computers
Step 2: Configuring Computers
The instructions in this chapter will help you to configure each of your
computers to be able to communicate with the Corinex Wireless to
Powerline AP.
This process differs between powerline connected computers and wireless
connected computers and it also depends on operating systems.
A. Using Powerline Connection
We advise you to read and use the Manual of your Powerline Adapter to
establish a Powerline connection between Corinex Wireless to Powerline
AP and Powerline Adapter. Use the Default Powerline (NEK) password
"HomePlug", as this is the factory default password setting for the Corinex
Wireless to Powerline AP. When you are using the Corinex Setup Tool to
configure your powerline adapter, you can check, whether your Adapter
has a powerline connection to the Corinex Wireless to Powerline AP by
searching in the last window of the Corinex Setup Tool for the MAC
addresses of the AP. You will find the MAC address of your Corinex Wireless
to Powerline AP on the label on the bottom of the AP´s plastic cover (MAC
PLC / SN).
6
Corinex Wireless to Powerline AP
Step 2: Configuring Computers
B. Using the Wireless Connection
You may need to reconfigure some wireless settings to ensure all settings
match between wireless devices.
Note: Different wireless settings will make successful wireless network
connections between wireless adapters impossible.
Default Wireless Interface Settings are as follows:
SSID: Corinex
Channel: 11
WEP: Disabled
Note: WEP is disabled by default for an easier installation. For
enhanced security, it is recommended that you later (after successful
configuration) enable WEP on all wireless devices.
C. TCP/IP Settings
7
Next you will need to configure your TCP/IP Settings. Computers use
IP addresses to communicate with each other across a network or the
Internet.
Find out which operating system is running your computer, like Windows
95, 98, Millennium, 2000, XP, Linux or Macintosh OS. We do give you
detailed configuration guide to the Windows XP Operating System. Other
operating systems have slight differences and we recommend to read the
Corinex Wireless to Powerline AP User Guide for detailed description how
to change TCP/IP settings on your Operating System.
Windows XP TCP/IP Settings
A. Click the Start button, then open the Control Panel. From there,
click the Network and Internet Connections icon and then the
Network Connections window appears.
Corinex Wireless to Powerline AP
Step 2: Configuring Computers
B. Select the Local Area Connection icon for the applicable adapter
(wireless adapter, if you are wireless connected or Powerline
Adapter if you are powerline connected. It is usually the first
adapter listed). Double-click the Local Area Connection.
C. The Local Area Connection Status screen will appear. Click the
Properties button.
D. Select Internet Protocol (TCP/IP) and click the Properties button.
Corinex Wireless to Powerline AP
8
Step 2: Configuring Computers
E. Select Obtain an IP address automatically and click the
OK button. Click the OK button again (or the Close button if any
settings were changed) to complete the computer configuration.
F. If you do not have DHCP server on the network, then select Use the
following IP address. Set the IP address manually in the shape
192.168.1.X and mask 255.255.255.0 of local TCP/IP settings and
click the OK button. On the next appearing screen click the OK
button again.
9
Corinex Wireless to Powerline AP
Step 3: Configuring the Access Point
Step 3: Configuring the Access Point
In this Step, you will configure the Corinex Wireless to Powerline Access
Point.
A. Open your web browser. (You can get an error message at this
point. Ignore it.) Enter http://192.168.1.1 in the web browser’s
Address field. Press the Enter key and the Corinex Wireless to
Powerline Access Point web-based configuration utility will start.
Address
http://192.168.1.1
B. Window requiring entering your password will appear. The default
password for the configuration utility is password. The password
is case sensitive. The configuration utility is used to configure
both the wireless and powerline aspects of your AP. The wizard
contains eight different dialog screen options accessible through
the following tabs:
- Home
- Status
- Help
- IP Address
- IP Address Settings
- Wireless
- Wireless Settings
- Wireless Mode
- Security Settings
- Powerline
- SNMP Agent
- NEK Password Setting
- Powerline Statistics
- Priority Settings
- Advanced
- MAC Address Filtering
- Block Sites
- Security Log
- Utilities
- Restart Access Point
- Restore Factory Default
- Save/Backup Current Settings
- Restore Previous Settings
- Firmware Update
- System Settings
10
Corinex Wireless to Powerline AP
Step 3: Configuring the Access Point
C. The Status screen will allow you to review your settings (Firmware
Version, Device Name, IP Settings and Wireless Settings).
C
D. On the Login screen, enter the default password, password, in
the Password field. Then click the Submit button. For enhanced
security, remember to change this password later through the
web-based utility (Utilities / System Settings).
11
D
Corinex Wireless to Powerline AP
Step 3: Configuring the Access Point
E. In the IP Address Settings page you can configure the IP address
used by the web-based utility running on this Access Point. If
DHCP Client is not enabled, the IP address settings are given here.
Otherwise, these settings are supplied by a DHCP server on your
network. If you have changed any settings it is necessary to reboot
the Access Point for the new settings to take effect.
E
F. The Wireless Settings page allows you to configure the wireless
settings. Enter your wireless network’s SSID, select the Channel
at which the network broadcasts its wireless signal, name of the
AP and fill all the other fields according to you settings requirements.
Any new settings will not take effect until the AP is rebooted.
F
Corinex Wireless to Powerline AP
12
Step 3: Configuring the Access Point
G. In the Wireless Mode page you can confi gure the Access Point to
perform in any one of two modes, as a wireless Access Point or as
a Wireless Client.
G
13
Corinex Wireless to Powerline AP
Step 3: Configuring the Access Point
H. In the Security Settings screen select the Encryption type,
Authentication type, Radius IP, WPA, WEP, etc. Set the Wired
Equivalent Privacy (WEP) for your wireless network. Select a WEP
or other encryption method and a passphrase. Click on Apply to
make changes.
14
H
Corinex Wireless to Powerline AP
Step 3: Configuring the Access Point
I. SNMP Agent - this feature lets you set up SNMP Agent settings.
I
J. The Network Encryption Key page allows you to configure the
Powerline settings. All Corinex Powerline and CableLAN devices are
shipped using "HomePlug" as the network encryption key (NEK).
The Security dialog screen allows you to change this encryption
key, to set your own private NEK and apply it to the Corinex Wireless
to Powerline Access Point. Click Apply button to make changes.
15
J
Note: NEK must be between 4 to 24 alphanumeric characters and is
case sensitive.
For detailed configuration procedures and functionality of the AP or
for installation with other operating system versions, please see the
Corinex Wireless to Powerline User Guide on the included CD-Rom.
Corinex Wireless to Powerline AP
Loading...