Page 1
Elegant
Bluetooth Headset
BTHS02
User Manual
Page 2
Page 3
BTHS02 User Manual
19
19
Contents
1. Before starting.................................................................................. ....... 20
2. Statements
................................................................................................ 21
3. Product Introduction............................................................................. 22
4. Quick Start Guide.................................................................................... 24
5. Wearing Headset ..................................................................................... 27
6. Function Specification.......................................................................... 28
6.1 Charging the heads
et..................................................... 28
6.
2 Power On/Off the headset............................................. 29
6.
3 Pairing................................................................................... 29
6.4 Making Calls
........................................................................ 30
6.5 Redial
..................................................................................... 30
6.
6 Voice Dialing....................................................................... 30
6.7 Answering a call
................................................................ 30
6.
8 End a call.............................................................................. 30
6.
9 Reject a call......................................................................... 30
6.10 Transfer/Switch Calls
..................................................... 31
6.11 Adjust the headset Volume
....................................... 31
6.12 Mute
.................................................................................... 31
6.13 Connect with a PC or PDA
........................................... 31
7. FAQ............................................................................................................... 32
8. Compatible Listing................................................................................. 34
9. Specification..............................................................................................35
Page 4
BTHS02 User Manual
2020
2121
2
1. For first time use, it should takes about 4 hours to fully
charge the battery. Afterward, it takes about 2 hours to fully
charge. Details please refer to the manual.
2. This manual was taken bluetooth mobil phone for instance
for pairing, other bluetooth devices please refer particular
manual.
3. You will see [CG-BTHS02] shown on the screen of the
bluetooth mobil phone or other bluetooth devices when
you’re pairing. Please select it and enter the password [1234]
to make sure the pairing successful.
Before starting
1
Page 5
BTHS02 User Manual
2121
2
Statements
BQB Statements
The Bluetooth Qualification information of this product could be referred to
Bluetooth Identifier B01818”.
FCC Safety Statements
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
The radiated output power is far below the FCC Radio frequency exposure limits.
Nevertheless, this device should be used in such a manner that the potential for
human contact during normal operation is minimized.
Warning: Changes or modifications made to this equipment not expressly ap
proved by the manufacturer. May void the FCC authorization to operate this
equipment.
Important. Please note the following:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal
lation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Copyright and Trademark Notices
Products and brand names may be the trademarks or registered trademarks of
their respective owners.
Page 6
BTHS02 User Manual
22
23
corega BTHS02 is an elegant styling bluetooth headset, which can
pairing with mobile phones, PDA, Desktop PC or notebooks and making
voice transmission within high distance of 10M. You may use corega
BTHS02 as wireless microphone when you talking through MSN mes
senger/Yahoo messenger or other IM softwares, or listen to the music
from PC or notebooks.
3.1 Packing Content
• Elegant Bluetooth Headset
• Charger (suitable for Nokia mobilphone)
• Charger Connector
• Ear Hook
• Cloth Bag
• Strap
• Ear Sponges
• Manual
3.2 Product Features
• Compatible with Bluetooth 1.1 Standard
• Fashion and stylish design
• High voice transmission quality without echo
• 2 easy wearing ways-direct to wear or wear with earhook
• Talking time up to 6 hours and standby time up to 160 hours
• Cover area up to 10m
• Support [Voice Dailing] and [Transfer/Switch calls] function.
• Support IM software, ex:MSN Messenger, Skype
• Low electromagnetic wave for health care
• Additional strap for wearing on neck
• Additional pretty bag for protecting the headset.
3
Product Introduction
Page 7
BTHS02 User Manual
23
3.3 Hardware Introduction
[Front] [Back]
Button
Button
Dial/Answering
/
Reject a call/Voice dialing
Vo
lume up
Pairing
Po
wer on/off
End/Redial a call
Vo
lume down
Microphone
Charging port
Speake
r
[Ear Hook]
Adjustable Hook
Page 8
BTHS02 User Manual
24
25
《Charging the headset 》(while LED is red)
(Check LED status)
DC Jack Connector
(Suitable for Nokia Mobilephone)
Power
Supply
Red (Green) LED
Charger
《Power on》
Press and hold the [] button for 4 seconds LED flashes blue light
for 4 times
release the [] button power on successful.
(Powering on status is LED flashes one time per several seconds)
《Power off》
Press and hold the [] button for 4 seconds LED flashes red light for
4 times release the [] button power off successful.
《Pairing with mobilphone》
Press and hold the [] button for 7 seconds LED flashes blue light
for 4 times LED flashes red and blue alternatively release the
[] button follow the mobilphone’s manual for pairing select
“CG-BTHS02” of the listing showed on your mobilphone screen
type
4
Quick Start Guide
Page 9
BTHS02 User Manual
25
password, “1234” pairing successful.
《Make a call》
Dialing by the mobilphone.
《Redial last call》
Press and hold the [] button for 3 seconds starting auto dialing
last call.
《Cancel dialing》
Press and release the [] button the call is canceled.
《Voice dialing》
(It depends on mobilphone’s voice dialing function)
Press and release the [
] button Say the telephone number (or
voice tag)
starting auto dialing.
《Answer a call》
Press and release the [] button start to talk.
《End a call》
Press and hold the [] button for 3 seconds the call is ended.
《Reject a call》
(while phone is ringing)
Press and hold the [
] button for 3 seconds the call is rejected.
《Adjust speaker volume》
Press and release the [] button volume up
Press and release the [
] button volume down
《Transfer/Switch Calls》
(While talking on the headset)
Page 10
BTHS02 User Manual
26
27
Press and hold [] button for 3 seconds transfer the call to the
mobile phone press and release [] button transfer the call back
to headset.
《Mute the Microphone》
Press and hold both [] and [] button for 3 seconds mute during
a call.
Press and hold both [] and [] button mute is canceled during a
call.
《Connect with a PC or PDA》
You are allowed to connect the headset with a Bluetooth enabled PC
or PDA that is with Audio Gateway Profiles supported. Please refer
to the user manual of your Bluetooth enabled PC or PDA for a setup
information.
5
Page 11
BTHS02 User Manual
27
There are 2 ways to wear the headset (either right or left side):
《Wearing the headset without ear hook》
1. Directly place the headset into your ear without the ear hook.
[Figure 1]
《Wearing the headset with a ear hook》
1. Buckle the ear hook onto the headset.
2. You may bend and adjust the hook to fit your ear, then gently place
the ear hook onto your ear. (Figure 2, ex: wearing onto left ear.)
3. You may take apart the ear hook and buckle the headset by the
contrary way if you want to exchange to the right ear. (Figure 3)
[Figure 2]
[Figure 3]
5
Wearing Headset
Page 12
BTHS02 User Manual
28
29
6.1 Charging the headset
The headset comes with an embedded rechargeable battery. For first
time use, it should takes about 4 hours to fully charge the battery. After
ward, it takes about 2 hours to fully charge. With battery fully charged,
the talk time is about 6 hours, and the standby time will be about 160
hours.
1. Connect the DC Jack Connector with transferred connector as
picture shown below.
2. Connect the other side of transferred connector to the rechargeable
port of the headset.
3. Plug the charger into the socket of the power supply.
4. Both red and green LEDs of transferred connector will light up.
DC Jack Connector
(Suitable for Nokia Mobilephone)
Power
Supply
Red (Green) LED
Charger
* Note:
1. When the red indicator of the headset starts to flash, it indicates that the
headset is running low on battery. Charge the headset for 2 hours until the red
indicator turns off.
2. The headset doesn’t work while charging.
6
Function Specification
Page 13
BTHS02 User Manual
29
6.2 Power On/Off the headset
《Power On》
Press and hold [] button for 4 seconds. While you see the LED flashes
blue light for 4 times and hear two short high tones, release [
] but-
ton, then it will be powered on.
《Power Off》
Press and hold [] button for 4 seconds. While you see the LED flashes
red light for 4 times and hear two low tones, release [
] button, then
it will be powered off.
6.3 Pairing
You are required to pair the headset with your mobile phone or other
devices before using it.
1. The headset must be powered off before initiating pairing. To initiate
pairing, press and hold [
] button for 7 seconds until the blue and
red indicators of headset are flashing alternatively. If you are wearing the headset during the pairing process, you will hear two short
high tones when the headset is ready for pairing.
2. Initiate pairing process of your mobile phone. Refer to the manual of
mobile phone for detail process. You will see a new item “CG-BTHS02”
added in your Bluetooth device list after searching process.
3. You will be asked to enter pin-code to complete pairing. Please enter
[1234] and confirm it.
* Note:
1. [1234] is the default pin-code.
2. The red indicator of headset will turn off and the blue indicator will flash
slowly after pairing completed successfully.
3. If the headset is not in pairing mode, your mobile phone won’t find the
headset. Please set the headset on pairing mode before the mobile phone
search for the headset.
4. If no pairing is possible for a period of time (approx. two minutes), the
headset will automatically power off, and so the previous pairing (if any) is
revoked. You may need to repeat steps 1 to 3 until pairing succeeds.
Page 14
BTHS02 User Manual
30
31
6.4 Making Calls
Dial the number on the mobile phone as you usually do.
6.5 Redial
Press and hold [] button for 3 seconds to redial the last number you
called.
6.6 Voice Dialing
Press [] button, waiting for a beep from headset and say the voice
tag or the name of the person you want to call. Press [
] button again
to cancel voice dialing.
* Note: It depens on the mobile phone which supports the function. And the
name you said has been to saved as a voice tag in mobile phone contact
listing.
6.7 Answering a call
When the headset is powered on and the mobile phone rings, you
will hear a musical tone and the blue indicator will change to be quick
flashing. Press [] button to answer the call.
* Note:
Due to the different design of some mobile phones, an auto-disconnect
may happen even when the headset is powered on. In that case, the
headset won’t ring when there is an incoming call. Press and release the []
button to reconnect the headset with mobile phone for an incoming call.
6.8 End a call
End calls by pressing and holding [] button for 3 seconds or do
nothing.
6.9 Reject a call
Press and hold [] button for 3 seconds to reject a call.
Page 15
BTHS02 User Manual
31
6.10 Transfer/Switch Calls
Press and hold [] button for 3 seconds to transfer the call to mobile
phone while talking on the headset. If you want to transfer the call
back to headset, press [] button again.
6.11 Adjust the headset Volume
Press [] button for volume up or press [] button for volume down.
6.12 Mute
Press both [] and [] buttons in the same time for a Mute function.
Press both [
] and [] buttons in the same time again to disable the
Mute function.
6.13 Connect with a PC or PDA
You are allowed to connect the headset with a Bluetooth enabled PC
or PDA that is with Audio Gateway Profiles supported. Please refer
to the user manual of your Bluetooth enabled PC or PDA for a setup
information.
Page 16
BTHS02 User Manual
32
33
Q1. Why doesn’t the headset work with my mobile phone after the head-
set has been fully charged and switched on?
Ans: You have to activate the Bluetooth function of your mobile phone
first and pair it with the headset.
Q2. Does the headset work with all types of mobile phones?
Ans: No. It works only with Bluetooth enabled mobile phones.
Q3. What is the operation distance between the headset and a
Bluetooth mobile phone?
Ans: The maximum operation distance can be up to 10 meters, however
it will be affected and shortened by different circumstances and dif
ferent brands of mobile phones. Some mobile phones are with less
operative distance.
Q4. When my mobile phone was searching for the headset, why did
several Bluetooth devices appear on my mobile phone?
Ans: Most Bluetooth enabled mobile phones with Bluetooth function
activated can search for more than one Bluetooth device within
operative range. The headset will appear as “CG-BTHS02” on your
mobile phone after having been found by your mobile phone.
Q5. Why can’t my mobile phone find the headset?
Ans: If the headset is not in pairing mode, your mobile phone won’t find
the headset. Please set the headset into pairing mode before starting your mobile phone to search for the headset. (Please refer to the
User Manual for detailed instructions.)
Q6. Do I need to pair the headset with my mobile phone every time I
use it?
Ans: No, once the Pairing is set up between the two devices, they will
remain paired even when one or both devices are powered off.
Q7. Why is there a disturbance noise coming from the headset?
Ans: Whether your mobile phone is in a good signal area. If your mobile
phone is in weak signal area, you won’t hear clearly with the headset.
7
FAQ
Page 17
BTHS02 User Manual
33
Q8. What should I do when I can’t hear very well with the headset?
Ans: Adjust the sound volume on your mobile phone, or press the [
]
button of the headset to make volume up, or check if your mobile
phone is in a good signal area.
Q9. Why doesn’t the headset work suddenly?
Ans:
1) The headset may have run out of battery. When it is in low battery, a
red LED will start to flash.
2) Some Bluetooth mobile phones have a problem with the Bluetooth
implementation, will occasionally but not often, get into an
Bluetooth shut-down status in unpredictable circumstances. When
this happens, please restart your mobile phone. (It is not necessary
to perform Pairing again.)
Make sure that your phone has the latest version of firmware loaded
onto it. Please check the website of your mobile phone for new
firmware.
Q10. Why doesn’t the voice dialing function work with the headset?
Ans: You may have to record the voice tag with the headset to your
mobile phone. So that it can make sure the voice or number you said
is right to correspond with the voice tag.
Page 18
BTHS02 User Manual
3434
3535
Compatible Mobile Phones Listing as below:
Brand name Model name
Nokia
3650 3660 6230 6260 6310 6310i 6600 6670 6820
7280 7610 8910 8910i N-Gage
Motorola
A760 A780 E398 E680 V3 V501 V525 V600 V600i
MPX220 V80
Sony
Ericsson
K700i P800 P900 P910i S700i T39 T610 T630 T68
Z600 T68i
Brand name Model name Brand name Model name
Panasonic
X70 X700 X88 Simens S55 S65 SX1
Sharp
GX-15 GX-30 GX-31 BenQ P30
Sagem My-X8 Philips
D535
Dopod
575 O2 XDA2
*Note: Latest compatible mobile listing please refer from http://www.corega-
asia.com.
8
Compatiable Listing
9
Page 19
BTHS02 User Manual
3535
Standard Bluetooth V1.1
Bluetooth Profile
Generic Access (GAP),
Service Discovery Application (SDAP),
Headset (HSP),
Handsfree (HFP)
Usage Time
Talk time: 6 hours
Standby time: 160 hours
Frequency 2.4GHz~2.4835GHz ISM Band
Spectrum FHSS (Frequency Hopping Spread Spectrum)
RF Output Power 0 dBm(typical)
Receiving Sensitivity -80 dBm(typical)
Power Class Class 2
Antenna Type PCB Antenna
Cover Range
Up to 10M (open space)
* Environmental factors may adversely affect
wireless signal range
Rechargeable
Battery
Battery Type:Li-ion polymer
Capacity:160 mAh
Nominal Voltage:3.7V
Recharging Voltage:4.2V
Recharging Current:100mA/5V DC
Security Pairing, 128bits Encryption Authentication
Power Consumption
Operation:30 mA
Standby <1 mA
Environment Requirements
Operating
Temperature:0~40˚C
Humidity:<90% (non- non-condensing)
Storage
Tempterature:-20~60˚C
Humidity:<95% (non- non-condensing)
Physical Specifications
Dimension 26(W ) x 24(D) x 60(H) mm
Weight
13 g
Certification DGT,CE,FCC,BQB
9
Specification
Page 20
memo
Page 21
memo
Page 22
Loading...