Corbin Russwin Access 700 TCPAC1 Series Installation Instructions Manual

700

™

TCPWI1

Installation Instructions ML20700 TCPAC1 Series

Mortise Lockset

FM324 09/09

Attention Installer

Please read these instructions carefully to prevent missing important steps.

Please Note: Improper installations may result in damage to the lock and void the factory warranty.

Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.

Misalignment can cause premature wear and a lessening of security.

For Technical Assistance call Corbin Russwin at 1-800-810-WIRE (9473)

ML20700 PWI Series Mortise Lock

1) Warning ................................................................................2

Table of Contents

2) General Description

3) Speciﬁcations / Features

4) Product Illustration

5) Installation Instructions

6) Operational Check

.............................................................3

....................................................3

.............................................................4

......................................................5

.............................................................18

1) Warning

Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced technician for help

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁcations were met. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer

!

l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.

To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

!

Observe precautions for handling electrostatic sensitive devices.

2

ML20700 PWI Series Mortise Lock

2) General Description

Designed speciﬁcally for the campus market, the Corbin Russwin Access 700 TCPAC1 Series mortise lock is a new breed of electronic lock, providing wireless online card/pin access control, as well as detailed audit |capabilities. Using WiFi technology and coupled with PERSONA Campus™ software, the P2 online lock offers a complete, integrated access control system.

The Passport 1000 P2 operates on six (6) “AA” alkaline batteries and may be used for both indoor and outdoor

applications. A weather-protective gasket is recommended for outdoor applications.

3) Speciﬁcations / Features

Hardware Speciﬁcations

• Latch – Stainless Steel (Easily eld reversible without disassembling lockbody)

• Deadbolt – Stainless Steel

• Door Thickness – 1-3/4” Standard; can be furnished for other door thicknesses upon request. Consult factory.

• Case – 12 gauge heavy duty wrought steel

• Outside lever controlled by keypad/magstripe card, or key retracts latch

• Inside lever retracts latch

• BHMA Grade 1; UL Fire Listed

• Card Coercivity: HiCo (400 Oersted) or LoCo (300 Oersted)

Electrical Speciﬁcations:

• 2400 users per door

• 2400 event transaction audit trail

• Multiple time zone and holiday access scheduling

• First-In unlock conguration, either by time or by valid time or by user (selectable)

• Input power: DC 9V, 1.5A (6 AA Alkaline Batteries or Electrical Power)

• Use existing magstripe ID cards (high or low coercivity)

• New key cards can invalidate and reactivate keycards/users – encoded quickly and easily through the “Conference Guest Wizard”

• Assign pre-dened access patterns and access points as well as key card start and end times

(group or individually)

3

ML20700 PWI Series Mortise Lock

4) Product Illustration

7

5

6

5

4

3

2

1

14

13

12

11

10

9

8

5

Inside

PWI

Outside

ITEM No. PART No. DESCRIPTION QTY

1 795F069 Light Pipe Lens 1

2 795F145 FIN Escutcheon, O/S, PWI With Keypad 1

2 795F135 FIN Escutcheon, O/S, PWI Without Keypad 1

3 795F059 Light Pipe 1

4 795F039 Keypad Assy 1

5 795F318 Screw #4-40x1/4 11

6 795F849 Swipe Reader 1

7 795F859 Onine Interface PCB 1

8 795F079 Online Harness 1

9 795F088 Mounting Plate 1

10 323F818 Screw, #8-32 x 2 4

11 743F768 Screw, #8 x 3/8 2

12 795F839 Electronics, Access 700PWI, 1

13 795F105 FIN Escutcheon, I/S 1

14 795F197 Screw, #8-32 x 1/2” Torx-Pin 2

4

ML20700 PWI Series Mortise Lock

5) Installation Instructions

1. Verify Hand and Bevel of door:

Illustrations shown are as viewed from the outside or secure side of opening.

Left Hand

Hinges Left.

Open Inward.

“LH”

Left Hand

Reverse Bevel

Hinges Left.

Open Outward

“LHRB”

Right Hand Hinges Right. Open Inward.

“RH”

Right Hand

Reverse Bevel

Hinges Right.

Open Outward

2. Prep door according to door template T31076 : visit www.corbinrusswin.com.

Through Bolt Holes

Backplate Mount Holes

Through Bolt Holes

Controller Cutout

Cylinder Hole

Trim Lever Hole

“RHRB”

Lever Handle Holes

Outside of Door

Mortise Pocket

5

Lever Handle Holes

Inside of Door

ML20700 PWI Series Mortise Lock

5) Installation Instructions (Continued)

3. Handing of Lock Body:

If necessary re-hand latch and move RED locking screw to side of lockbody to side of lock body to be locked:

a. Push in latch while gently pushing on catch plate with screwdriver (Fig. 3a).

b. Release latch and remove from lock body.

c. Turn over latch and re-install in lock body; Be sure anti-friction latch tail hooks into front (Fig. 3c).

d. Hold screwdriver behind tail socket while pushing in latch. Push latch until ‘click’ is heard (Fig. 3b).

Note: Pull on latch to make sure it is secure.

e. Rotate lock front to match bevel of door by inserting screwdriver into lock mounting holes

and twisting (Fig. 3d).

Fig. 3a

Fig. 3c

Fig. 3b

Move the RED-HEADED screw to

the Locking Side of the door

Anti-friction Latch Tail

Lock Front

Fig. 3d

6

Corbin Russwin Access 700 TCPAC1 Series Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual