Corbin Russwin Access 700 CL33700 TCPWI1 Series, CL33700TCPIP1, Access 700 CL33700 TCPIP1 Series Installation Instructions Manual

700

™

TCPWI1/TCPIP1

Installation Instructions CL33700 TCPWI1 & TCPIP1Series

Cylindrical Lockset

Attention Installer

Please read these instructions carefully to prevent missing important steps.

Please Note: Improper installations may result in damage to the lock and void the factory warranty.

Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.

Misalignment can cause premature wear and a lessening of security.

FM323 3/14

For Technical Assistance call Corbin Russwin at 1-800-810-WIRE (9473)

CL33700 PWI/PIP Series Cylindrical Lock

Table of Contents

1) Warning ................................................................................2

2) General Description .............................................................3

3) Speciﬁcations / Features ....................................................3

4) Product Illustration .............................................................4

5) Installation Instructions ......................................................5

6) TCPIP (PoE) Wiring Instructions........................................17

7) Operational Check .............................................................21

1) Warning

Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced technician for help

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry Canada technical speciﬁcations were met. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.

To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

!

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:

!

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door.

• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation

• Do not touch pins, leads or solder connections on the circuit boards

2

CL33700 PWI/PIP Series Cylindrical Lock

2) General Description

Designed speciﬁcally for the campus market, the Corbin Russwin Access 700 series mortise Locks are available in WiFi (PWI) and PoE (PIP) conﬁgurations. Coupled with third party software the PWI and PIP offers a complete, integrated access control system. The Access 700 may be used for both indoor and outdoor applications (weather-protective gasket supplied).

The Access 700 PWI operates on six (6) “AA” alkaline batteries and may be used for both indoor and outdoor applications. A weather-protective gasket is provided for outdoor applications.

3) Speciﬁcations / Features

Hardware Speciﬁcations

• Latch – Stainless steel, ½” (13mm) throw Optional: ¾” (19mm) throw deadlocking ﬁre latch for pairs of doors

• Deadlocking latch prevents manipulation when door closed

• Door Thickness – 1-3/4” (44mm) to 2” (50mm) Standard Optional 2” (50mm) to 2-1/4” (57mm) optional

• Outside lever controlled by keypad/magstripe card, or key retracts latch

• Inside lever retracts latch

• BHMA Grade 1, UL Fire Listed*

Electrical Speciﬁcations:

• HID® multiCLASS SE™ technology offers support for the following credentials:

• High Frequency (13.56 MHz):

• HID iCLASS

• HID iCLASS SE® (SIO-enabled)

• HID iCLASS® Seos

• HID MIFARE® SE

• HID DESﬁre® EV1 SE

• MIFARE Classic

• DESﬁre EV1

• FeliCa

• Low Frequency (125 kHz):

• HID Prox

• Magnetic Stripe

• NFC-enabled Mobile Phones

®

™

®

*Any retroﬁt or other ﬁeld modiﬁcation to a ﬁre rated opening can potentially impact the ﬁre rating of the opening, and Corbin Russwin, Inc. makes no representations or warranties concerning what such impact may be in any speciﬁc situation. When retroﬁtting any portion of an existing ﬁre rated opening, or specifying and installing a new ﬁre-rated opening, please consult with a code specialist or local code ofﬁcial (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.

3

CL33700 PWI/PIP Series Cylindrical Lock

4) Product Illustration

5

4

1

2

3

ITEM No. PART No. DESCRIPTION

1 784F565 FIN Outside Escutcheon Assembly, Mag Swipe

784F575 FIN Outside Escutcheon Assemby, Mag Swipe and Keypad

784585 FIN Outside Escutcheon Assemby, Mag Swipe, Keypad, HID 125kHz Prox, and 13.56 MHz Prox

784595 FIN Outside Escutcheon Assemby, Mag Swipe, HID 125kHz Prox, and 13.56 MHz Prox

784F605 FIN Outside Escutcheon Assemby, Mag Swipe, Keypad, HID 125kHz Prox, and 13.56 MHz Felica

784F615 FIN Outside Escutcheon Assemby, Mag Swipe, HID 125kHz Prox, and 13.56 MHz Felica

2

3

4 782F788 Mounting Plate Assembly

5 784F515 FIN Inside Escutcheon Assembly with Privacy Button

783F519 WiFi Controller Assembly

783F509 PoE Controller Assembly

795F368 Screw Pack

6

4

CL33700 PWI/PIP Series Cylindrical Lock

4) Product Illustration (Continued)

Tools Required:

• Phillips Screw Driver #2, #3

• Flat Blade Screw Driver (Standard size)

• 1/8” Security Allen Wrench (supplied

• 7/64” Allen Wrench (supplied)

• T20 Security torx driver (supplied)

4

2

3

1

1 783F918 CL33134 Cylindrical lock with ﬁxed core cylinder 1

783F928 CL33134 Cylindrical lock with removable core cylinder 1

2 784F118 Inside Spring Cassette - REX (D134) 1

784F128 Inside Spring Cassette - REX (D214) 1

3 682F268 Outside Spring Cassette (1-3/4” - 2” Door) 1

682F278 Outside Spring Cassette (2” - 2-1/4” Door) 1

4 783F619 DPS (Door Position Switch) Kit 1

For parts not listed, refer to CL3300 Parts and Service Manual

5

CL33700 PWI/PIP Series Cylindrical Lock

5) Installation Instructions

1. Verify Hand and Bevel of door:

Illustrations shown are as viewed from the outside or secure side of opening.

Left Hand

Hinges Left.

Open Inward.

“LH”

Left Hand

Reverse Bevel

Hinges Left.

Open Outward

“LHRB”

Right Hand Hinges Right. Open Inward.

“RH”

Right Hand

Reverse Bevel

Hinges Right.

Open Outward

“RHRB”

2. Prep door according to supplied Door Marker (FM302). For door manufacturer templates visit www.corbinrusswin.com and reference Template # T31077.

Inside of Door

Escutcheon Through Bolt Holes

Inside Mouthing Plate Holes

Controller Wire Hole

Wire Run Channel

Escutcheon Through Bolt Holes

Controller Wire Hole

Lockbody Through Bolt Holes

Outside of Door

Door

Position

Switch

Alignment Notches

Lock Body Prep

Latch Front

and Hole

Wood Door Preparation

6

Lock Body Through Bolt Holes

Alignment Notches

Lock Body Prep

CL33700 PWI/PIP Series Cylindrical Lock

5) Installation Instructions (Continued)

3. Install Latch Bolt:

Install using two #8 x 3/4” combination screws (Fig. 3).

Note: Make sure the beveled bolt is facing the strike.

4. Install Strike:

Install using two #12 x 1” combination screws (Fig. 4).

Optional Strike Box

Fig. 3

Centerline of Latch Front and Strike

Fig. 4

7

Corbin Russwin Access 700 CL33700 TCPWI1 Series, CL33700TCPIP1, Access 700 CL33700 TCPIP1 Series Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual