FIXTURE PREPARATION
1. Remove the fixture and parts bag(s) from the carton.
NOTICE
· The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that
may occur. It must be understood that common sense, caution and care factors that cannot be built into any product. Caution
and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.
· This fixture is design to be mounted on a correctly installed standard round or octagon box or a through wiring box with a
plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be
used. Directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
FIXTURE INSTALLATION
CAUTION
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH
ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
· INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR
CERTIFIED FACTORY TRAINED TECHNICIAN.
· If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.
DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.
In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common" lead.
In older buildings it is always good practice to reconfirm the polarity of the wiring.
Page 1 of 4
L I
G
H T I N
R
G
213-42 2LTS CALLIGRAPHY PENDANT INSTALLATION INSTRUCTIONS
WARNING
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
1. Insert the aircraft cable into the cable grip post of the canopy. Push the tab down
on the cable grip and feed the aircraft cable. Repeat this step until you have
insert all aircraft cable. (Refer Figure-1)
NOTE:
Insure the height of aircraft cable and SVT wire would be sufficient as you
hang the fixture
2. Insert the SVT wire to bushing. (Refer Figure-1)
OUTLET BOX
FIGURE-1
3. To change the drop height based on your desired height, push the tab down on the grip post
either pull or push the aircraft cable. Repeat this to all aircraft cable until the fixture is level
and with the desired height. (Refer to Figure-4)
4. Adjust the SVT wire base on the desired height. Pull/push the SVT wire to the bushing and
leave 8" lead wire above the canopy and cut the excess wire. (Refer to Figure-4)
NIPPLE
HEX NUT
CROSS BAR
PUSH DOWN
(AIRCRAFT CABLE)
(CENTER LOCK UP)
(CABLE GRIP LOCK)
BUSHING
(SVT LEAD WIRE)
STRUCTURE OR BRACE
WHITE WIRE
WHITE WIRE
BLACK WIRE
BLACK WIRE
NOTICE:
Before discarding the carton,
double check to make certain that all parts are found.
MOUNTING
SCREW
Page 2 of 4
8. Thread the hex nut onto the nipple and the nipple into the crossbar.
Place the canopy over the nipple and against the ceiling. Adjust the nipple so
that 1/2" of threads extend beyond the canopy. (Refer to Figure 1)
ELECTRICAL TAPE
APPROVED FASTENER
(WIRE NUT)
Replacement LED Instruction
LED LIGHT
LED WIRE
LABEL FOR (-)
BLACK WIRE
LED GLASS
HEATSINK
WHITE WIRE
LED WIRE
LABEL FOR (+)
NOTE: THERMAL PAD
SHOULD BE PLACE
BETWEEN LED LIGHTS
AND HEATSINK
6. Fasten the white wire of the led light to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut). Starting about 1" below
the fastener, tightly wrap the connection with electrical tape so that the connections
seals the end of the fastener. (See Figure 2)
7. Connect the black wire of the led light to the black wire in the outlet box. Fasten the
joined wire as in step 6.
LED LIGHT TO OUTLET BOX
WIRE CONNECTION DETAILS
FIXTURE'S LED LIGHT BLACK WIRE
FIXTURE'S LED LIGHT WHITE WIRE
FIGURE-2
WHITE WIRE (NEUTRAL) FROM OUTLET BOX
BLACK WIRE (HOT) FROM OUTLET BOX
WARNING
Make sure that there is no exposed wire or strands that could
cause a dangerous short circuit!
NOTE:
LED light will be received assembled as in
Replacement LED Instruction
NOTE:
Need another person that will hold the fixture during
installation.
9. Using the center lock up, loosely fasten the fixture to the outlet box.
Adjust the orientation of the fixture. Refer to step 3 and 4 and Figure 4.
10. Once the required orientation met, tighten the center lock. Refer to Figure 1 & 4.
11. Restore power to circuit at breaker or fuse box.
5. Attach the crossbar to the outlet box using the mounting screws. (Refer Figure-1).
NOTICE:
This luminaire must be mounted or supported independently of an
outled box.
NOTICE:
Must use a incandescent dimmer with LED's on this fixture.
*Lutron Maestro dimmer not compatible.
FIXTURE A
LED GLASS
FIXTURE B
FIGURE-3
5/32" HOLE
HEATSINK
FROM FIXTURE A
PARAGON LED
LED GLASS
#6-32 BOLT
FROM FIXTURE B
3X LOCATION
#6-32 TAP
Page 3 of 4
SANBLAST GLASS
(OUTSIDE)
SHOWER GLASS
(INSIDE)
#6-32 BOLT(3PCS)
FIXTURE REASSEMBLY
2. Identify Fixture B, place the glass on the top of fixture. Refer to Figure-3.
NOTE:
Fixture should be reassemble prior to installation.
3. Attach Fixture B to Fixture A using the provided bolt. Use the appropriate tool in tightening the bolt. Refer to Figure-3
1. Identify Fixture A, Remove the protective cover on the LED Light on the bottom portion.
WASHER-2PCS
WASHER-2PCS
WASHER-2PCS
FIGURE- 4
PUSH DOWN
(AIRCRAFT CABLE)
(CENTER LOCK UP)
(CABLE GRIP LOCK)
BUSHING
(SVT LEAD WIRE)
Page 4 of 4
1112LLB
Loading...