Page 1
Green screw
L I
G
H T I N
R
G
FIXTURE PREPARATION
1. Remove the fixture, glass/metal parts and parts bag(s) from the carton.
NOTICE:
Before discarding the carton,
double check to make certain that all parts are found.
166-13 HARLOW LED ADA SCONCE INSTALLATION INSTRUCTIONS
WARNING
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
NOTICE
· The important safeguards and instructions outlined on this sheet cannot cover all possible
conditions and situations that may occur. It must be understood that common sense,
caution and care factors that cannot be built into any product. Caution and care must be
supplied by the person(s) installing, operating and caring of this lighting fixture.
· This fixture is design to be mounted on a correctly installed standard round or octagon box
or a through wiring box with a plaster frame. The box must be securely mounted to the
structure of the building. The crossbar and hardware supplied should be used.Directly
mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
FIXTURE INSTALLATION
1. Attach the mounting ring to the outlet box.
CAUTION
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH
ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
· INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR
CERTIFIED FACTORY TRAINED TECHNICIAN.
· If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.
DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.
In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common" lead
A GREEN or BARE COPPER wire is the "Ground". In older buildings it is always good practice to reconfirm the polarity of the wiring.
Page 1 of 2
Backplate
Outlet box
Mounting ring
Flat screw
Top glass
Bottom glass
Finial
End cap
Place top
glass here
Place bottom
glass here
Center stem
Stainless trim
Metal column
FIGURE-1
Silicon
Washer
LED DRIVER
Led Driver
Page 2
2. Fasten the white fixture lead to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut).
Starting about 1" below the fastener, tightly wrap the connection
with electrical tape so that the connections seals the end of the fastener.
WARNING
Make sure that there is no exposed wire or strands
that could cause a dangerous short circuit!
3. Connect the black fixture lead to the black wire in the outlet box.
Fasten the joined wires as in step 3.
4. Using the two (2) flat screws, fasten the fixture to the outlet box.
5. Attach the two (2) center stem and place the glass column
together with the stainless trim, place the end cap and screw
the finial to hold the glass column in place (See figure-1).
Page 2 of 2
NOTICE:
Must use a ELV Dimmer with LED's on this fixture.
*Lutron Maestro dimmer not compatible.
230812JP
LED
Driver
L
WHITE WIRE (NEUTRAL) FROM JUNCTION BOX
BLACK WIRE (HOT) FROM JUNCTION BOX
LED DRIVER'S (NEUTRAL) BLUE/WHITE
WIRE
LED DRIVER'S (HOT) BROWN/BLACK
WIRE
LED DRIVER'S BLACK (-) WIRE
LED DRIVER'S RED (+) WIRE
FIXTURE'S LED LAMP BLACK WIRE
FIXTURE'S LED LAMP RED WIRE
N
NOTE: THERMAL PASTE
SHOULD BE APPLIED
BETWEEN LED LIGHTS
AND HEATSINK
BLACK WIRE
RED WIRE
LED LIGHT(4pcs)
HEATSINK
Replacement LED Instruction
FIGURE-3
LED LAMP TO LED DRIVER
WIRE CONNECTION DETAILS
SEE ALSO DRIVER COLOR CODING
Loading...