Page 1
L I
G
H T I N
R
G
FIXTURE PREPARATION
1. Remove the fixture, glass/metal prism, parts and parts bag(s) from the carton.
NOTICE:
· Before discarding the carton, double check to
make certain that all parts are found.
· Do not remove the tripod until after installation.
· Only handle/lift fixture by tripod or center stem.
CAUTION
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH
ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
· INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR
CERTIFIED FACTORY TRAINED TECHNICIAN.
· If an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached.
DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING.
In regular circumstances the BLACK wire will be the "Hot" lead and the WHITE wire will be the "Neutral" or "Common" lead
A GREEN or BARE COPPER wire is the "Ground". In older buildings it is always good practice to reconfirm the polarity of the wiring.
154-46 GRAFFITI MEDIUM PENDANT INSTALLATION INSTRUCTIONS
WARNING
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
NOTICE
· The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that
may occur. it must be understood that common sense, caution and care factors that cannot be built into any product.
Caution and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.
· This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box
with a plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied
should be used. directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
· This fixture is supplied with with a 4-pcs. stem. There is one 6" section, two 12" section and one 18" section.
This feature allows the fixture to be mounted with a stem up to 48" in length in 6" increments (See figure-2)
· This fixture is supplied with a swivel. By rotating the canopy the fixture may be mounted to angled ceiling.
Page 1 of 3
Canopy
Adjustable stem
Ceiling
Swivel
SAFETY CABLE
Structure or Brace
Outlet box
Cable clamp
FIGURE-1
Swivel Blocker
Small Hex Nut
Stud
Stud's Hex Nut
Heavy Duty Strap
Green Screw
Nipple
Ball Nut
FIXTURE INSTALLATION
1.
Attach the SAFETY CABLE to the building structure or brace (See figure-1)
.
WARNING
REFER TO THE ILLUSTRATION FOR CORRECT AND SAFE
INSTALLATION OF SAFETY CABLE. FAILURE TO FOLLOW
THIS INSTRUCTION COULD RESULT HARM/DAMAGE TO
THE FIXTURE, PROPERTY AND/OR PERSON(S)!
NOTICE:
THIS LUMINAIRE MUST BE MOUNTED OR
SUPPORTED INDEPENDENTLY OF AN OUTLET BOX.
Page 2
Page 2 of 3
ADJUSTABLE STEM
FIGURE-2
2. Determine the overall desired length of the fixture.
Assemble the adjustable stems one at a time onto
the fixture leads. Tape the end of the leads to a stiff wire
(coat hanger) to aid in pulling them through the stems.
Place the canopy onto the stem. Assemble the top stem
section, decorative breaker, fixture stem and swivel.
Place the swivel blocker over the nipple of the canopy
and thread the hex nuts onto them.
3. Attach the heavy duty strap to the outlet box.
(The green screw should face the floor).
Thread the studs into the heavy duty strap at the spacing
that matches the mounting holes in the canopy. Adjust
the screw so they extend 3/16'' beyond the canopy.
4. Cut off the excess ground and fixture wire 6'' beyond
the canopy. Strip
1
2
'' of insulation from the ends of the wire.
Twist the wire stands together.
5. Fasten the ground wire to the green or bare copper wire
in the outlet box or the green screw on the
heavy duty
strap
.
6.
Fasten the white fixture lead to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut).
Starting about 1" below the fastener, tightly wrap the connection
with electrical tape so that the connections seals the end of the
fastener.
7. Connect the black fixture lead to the black wire in the outlet box.
Fasten the joined wires as in step 6.
8. Attach the SAFETY CABLE to the building structure or brace (See figure-1).
WARNING
Never fasten the ground wire to the black
or "hot" wire! Failure to follow this instruction
could result in serious injury or death!
Approved fastener ( wire nut )
Electrical tape
WARNING
Make sure that there is no exposed wire or strands
that could cause a dangerous short circuit!
WARNING
REFER TO THE ILLUSTRATION FOR CORRECT AND SAFE
INSTALLATION OF SAFETY CABLE. FAILURE TO FOLLOW
THIS INSTRUCTION COULD RESULT HARM/DAMAGE TO
THE FIXTURE, PROPERTY AND/OR PERSON(S)!
9. Using the ball nuts, loosely fasten the fixture to the
heavy duty strap. Rotate and align the canopy as
necessary. Tighten the ball nuts.
10. Place the glass (See figure-3) using the special tool
supplied.
11. Once the fixture is installed, remove the tripod.
(Rotate the tail lock, that holds the tripod,
in a counterclockwise direction.)
12. Attach the tail lock at the bottom of the fixture
by rotating it clockwise.
13. Install the lamps (G9 lighting bulbs).
NOTE: This fixture is rated for 50 watts G9 lamp.
WARNING
DO NOT EXCEED RECOMMENDED WATTAGE!
14. Restore power to circuit at breaker or fuse box.
Page 3
Page 3 of 3
022613ID
Threaded cap
Glass
Socket cover
Adjustable stem
SPECIAL TOOL
Lamp
FIGURE-3
Safety cable
Tail Lock
Tripod
Loading...