Corbett Lighting 401-30 INSTALLATION INSTRUCTIONS

FIXTURE INSTALLATION

WARNING/CAUTION

· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.

· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH
HANDS AFTER USE.

· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE
PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

4

1

2

3

www.hvlgroup.com

Questions? We're here to help!

Contact us at [e-mail]

ITEM DESCRIPTION

PART NUMBER

1

CROSSBAR HDW-401-30

2

MOUNTING SCREW HDW-401-30

3

CHAIN CHN-401-30
4 CANOPY CPY-401-30-T
5

SCREW COLLAR

HDW-401-30

6

CANOPY CPY-401-30-B

7 SCREW COLLAR LOOP

HDW-401-30

8

1/4 NIPPLE

HDW-401-30

9

GROUND SCREW

HDW-401-30
10 WIRE NUT HDW-401-30
11

BULB

NOT INCLUDED

12 FIXTURE ASSEMBLY FAS-401-30

5

6

7

8

9

10

11

PHOENIX

401-30

INSTALLATION INSTRUCTIONS

12

R

1. Attach the CROSSBAR (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is designed to
be mounted on standard round or octagon junction box. The junction box must be securely mounted to the
structure of the building.

2. Assemble the fixture by threading the four stems in to the fixture and to canopy (4).

3. Open the end link on the CHAIN (3) and attach to the loop on the CANOPY (4). Hang the FIXTURE
ASSEMBLY (12) on the CHAIN (3) at your desired height, and remove excess CHAIN.

4. Feed the wire through the CHAIN (3) , SCREW COLLAR (5), CANOPY (6), SCREW COLLAR LOOP (7),
NIPPLE (8), and CROSSBAR (1), and screw the NIPPLE (8) onto the CROSSBAR (1).

5. Open the top link on the CHAIN (3),and Hang the FIXTURE ASSEMBLY(12) to the SCREW COLLAR LOOP (7).

6. Cut off excess wire, and strip the insulation off the end of the leads.

7. Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bar copper wire) or
the GROUND SCREW (9) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT"

WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

8. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener (WIRE NUT) (10). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

9. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires
same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS

COULD RESULT IN SERIOUS INJURY OR DEATH!

10. Push the wires back into the junction box. Lift up the CANOPY (6) up to the ceiling, and screw the SCREW
COLLAR LOOP (7) onto the SCREW COLLAR (5).

11. Screw the BULB (11) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 6 WATT TYPE G 16 1/2 LED

LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!

12. Restore power to the outlet at the breaker or fuse box.

R

INSTALLATION INSTRUCTIONS

1

2

3

4

PHOENIX

401-30

10

9

8

7

6

5

· DÉBRANCHEZ L'ALIMENTATION AVANT DE REMPLIR OU DE CÂBLER LE LUMINAIRE. LISEZ

COMPLÈTEMENT TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L'INSTALLATION

· POUR ÉVITER LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, LE LUMINAIRE DOIT ÊTRE INSTALLÉ

CONFORMÉMENT À TOUS LES CODES ÉLECTRIQUES/DE CONSTRUCTION NATIONAUX ET LOCAUX
APPLICABLES. L'INSTALLATION ET L'ENTRETIEN DE CET APPAREIL DOIVENT ÊTRE EFFECTUÉS PAR UN
ÉLECTRICIEN AGRÉÉ OU UN TECHNICIEN CERTIFIÉ FORMÉ EN USINE.

· CALIFORNIE PROP 65 : CET APPAREIL D'ÉCLAIRAGE CONTIENT DES PRODUITS CHIMIQUES CONNUS PAR

L'ÉTAT DE CALIFORNIE POUR PROVOQUER LE CANCER, DES MALADIES CONGÉNITALES ET/OU D'AUTRES
DOMMAGES À LA REPRODUCTION. LAVER LES MAINS APRÈS UTILISATION.

· RETIRER LE LUMINAIRE, LES PIÈCES ET LE(S) SAC(S) DE PIÈCES DU CARTON. AVANT DE JETER LE

CARTON, VÉRIFIEZ DOUBLE POUR VOUS ASSURER QUE TOUTES LES PIÈCES SONT TROUVÉES.
INSPECTER LE LUMINAIRE AVANT L'INSTALLATION POUR TOUT DOMMAGE AU LUMINAIRE.

· GRADATION : LE LUMINAIRE PEUT ÊTRE CONTRLÉ PAR UN DISPOSITIF DE GRADATION MURALE. UTILISER

UNIQUEMENT UN GRADATEUR TRIAC/ÉLECTRONIQUE. ASSUREZ-VOUS QUE LE CARTON EST MARQUÉ
POUR UNE UTILISATION AVEC UNE SOURCE DE LUMIÈRE FLUORESCENTE À INCANDESCENTE COMPACTE
UNIQUEMENT. CEUX-CI PEUVENT ÊTRE FOURNIS PAR VOTRE DISTRIBUTEUR ÉLECTRIQUE LOCAL,
CENTRE À DOMICILE OU MAGASIN DE QUINCAILLERIE.

· VEUILLEZ NETTOYER UNIQUEMENT AVEC UN CHIFFON DOUX ET SEC ! N'UTILISEZ PAS DE NETTOYANTS

FIXTURE INSTALLATION

ATTENTION PRUDENCE

1. Attach the CROSSBAR (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is designed to
be mounted on standard round or octagon junction box. The junction box must be securely mounted to the
structure of the building.

2. Assemble the fixture by threading the four stems in to the fixture and to canopy (4).

3. Open the end link on the CHAIN (3) and attach to the loop on the CANOPY (4). Hang the FIXTURE
ASSEMBLY (12) on the CHAIN (3) at your desired height, and remove excess CHAIN.

4. Feed the wire through the CHAIN (3) , SCREW COLLAR (5), CANOPY (6), SCREW COLLAR LOOP (7),
NIPPLE (8), and CROSSBAR (1), and screw the NIPPLE (8) onto the CROSSBAR (1).

11

ITEM DESCRIPTION

1
2
3

CROSSBAR HDW-401-30

MOUNTING SCREW HDW-401-30

CHAIN CHN-401-30
4 CANOPY CPY-401-30-T
5
6

SCREW COLLAR

CANOPY CPY-401-30-B
7 SCREW COLLAR LOOP
8
9

1/4 NIPPLE

GROUND SCREW

HDW-401-30

HDW-401-30
HDW-401-30

HDW-401-30
10 WIRE NUT HDW-401-30
11

BULB

NOT INCLUDED

12 FIXTURE ASSEMBLY FAS-401-30

www.hvlgroup.com

12

PART NUMBER

5. Open the top link on the CHAIN (3),and Hang the FIXTURE ASSEMBLY(12) to the SCREW COLLAR LOOP (7).

6. Cut off excess wire, and strip the insulation off the end of the leads.

7. Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bar copper wire) or

the GROUND SCREW (9) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT"

WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

8. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener (WIRE NUT) (10). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

9. Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires
same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS

COULD RESULT IN SERIOUS INJURY OR DEATH!

10. Push the wires back into the junction box. Lift up the CANOPY (6) up to the ceiling, and screw the SCREW
COLLAR LOOP (7) onto the SCREW COLLAR (5).

11. Screw the BULB (11) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 6 WATT TYPE G 16 1/2 LED

LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!

12. Restore power to the outlet at the breaker or fuse box.

Questions? We're here to help!

Contact us at [e-mail]