Page 1
FIXTURE INSTALLATION
WARNING/CAUTION
· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS
COMPLETELY BEFORE STARTING INSTALLATION.
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.
· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH
HANDS AFTER USE.
· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE
CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE
PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE
TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
4
1
2
3
www.hvlgroup.com
Questions? We're here to help!
Contact us at CustomerService@hvlgroup.com
ITEM DESCRIPTION
PART NUMBER
1
MOUNTING STRAP HDW-401-12
2
MOUNTING SCREW HDW-401-12
3
CANOPY CPY-401-12
4 RS CAP CAP-401-12
5 BULB
NOT INCLUDED
6
FIXTURE ASSEMBLY FAS-401-12
5
PHOENIX
401-12
INSTALLATION INSTRUCTIONS
6
R
1. Attach the MOUNTING STRAP (1) to the junction box. (The green screw should face the floor) Place the
MOUNTING STRAP (1) at the junction box and fasten using the MOUNTING SCREW (2).
Adjust the nipple so they extend 3/16'' beyond the CANOPY (3).
2. Fasten the ground wire to the green or bare copper wire in the outlet box or the green screw on the MOUNTING
STRAP (1).
3. Fasten the white fixture lead to the white wire in the outlet box.Fasten the wires together with an approved
fastener (wire nut). Starting about 1" below the fastener, tightly wrap the connection with electrical tape so that
the connections seals the end of the fastener.
4. Connect the black fixture lead to the black wire in the outlet box.
5. Attach the CANOPY (3) to the MOUNTING STRAP (1) and secure it with the RS CAP (4).
6. Screw the BULB (5) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 40 WATT TYPE G 16 1/2
LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
7. Restore power to the outlet at the breaker or fuse box.
Page 2
www.hvlgroup.com
Questions? We're here to help!
Contact us at CustomerService@hvlgroup.com
ITEM DESCRIPTION
PART NUMBER
1
MOUNTING STRAP HDW-401-12
2
MOUNTING SCREW HDW-401-12
3
CANOPY CPY-401-12
4 RS CAP CAP-401-12
5 BULB
NOT INCLUDED
6
FIXTURE ASSEMBLY FAS-401-12
R
INSTALLATION INSTRUCTIONS
1
2
3
PHOENIX
401-12
· DÉBRANCHEZ L'ALIMENTATION AVANT DE REMPLIR OU DE CÂBLER LE LUMINAIRE. LISEZ
COMPLÈTEMENT TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L'INSTALLATION
· POUR ÉVITER LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, LE LUMINAIRE DOIT ÊTRE INSTALLÉ
CONFORMÉMENT À TOUS LES CODES ÉLECTRIQUES/DE CONSTRUCTION NATIONAUX ET LOCAUX
APPLICABLES. L'INSTALLATION ET L'ENTRETIEN DE CET APPAREIL DOIVENT ÊTRE EFFECTUÉS PAR UN
ÉLECTRICIEN AGRÉÉ OU UN TECHNICIEN CERTIFIÉ FORMÉ EN USINE.
· CALIFORNIE PROP 65 : CET APPAREIL D'ÉCLAIRAGE CONTIENT DES PRODUITS CHIMIQUES CONNUS PAR
L'ÉTAT DE CALIFORNIE POUR PROVOQUER LE CANCER, DES MALADIES CONGÉNITALES ET/OU D'AUTRES
DOMMAGES À LA REPRODUCTION. LAVER LES MAINS APRÈS UTILISATION.
· RETIRER LE LUMINAIRE, LES PIÈCES ET LE(S) SAC(S) DE PIÈCES DU CARTON. AVANT DE JETER LE
CARTON, VÉRIFIEZ DOUBLE POUR VOUS ASSURER QUE TOUTES LES PIÈCES SONT TROUVÉES.
INSPECTER LE LUMINAIRE AVANT L'INSTALLATION POUR TOUT DOMMAGE AU LUMINAIRE.
· GRADATION : LE LUMINAIRE PEUT ÊTRE CONTRLÉ PAR UN DISPOSITIF DE GRADATION MURALE. UTILISER
UNIQUEMENT UN GRADATEUR TRIAC/ÉLECTRONIQUE. ASSUREZ-VOUS QUE LE CARTON EST MARQUÉ
POUR UNE UTILISATION AVEC UNE SOURCE DE LUMIÈRE FLUORESCENTE À INCANDESCENTE COMPACTE
UNIQUEMENT. CEUX-CI PEUVENT ÊTRE FOURNIS PAR VOTRE DISTRIBUTEUR ÉLECTRIQUE LOCAL,
CENTRE À DOMICILE OU MAGASIN DE QUINCAILLERIE.
· VEUILLEZ NETTOYER UNIQUEMENT AVEC UN CHIFFON DOUX ET SEC ! N'UTILISEZ PAS DE NETTOYANTS
FIXTURE INSTALLATION
1. Attach the MOUNTING STRAP (1) to the junction box. (The green screw should face the floor) Place the
MOUNTING STRAP (1) at the junction box and fasten using the MOUNTING SCREW (2).
Adjust the nipple so they extend 3/16'' beyond the CANOPY (3).
ATTENTION PRUDENCE
6
5
4
2. Fasten the ground wire to the green or bare copper wire in the outlet box or the green screw on the MOUNTING
STRAP (1).
3. Fasten the white fixture lead to the white wire in the outlet box.Fasten the wires together with an approved
fastener (wire nut). Starting about 1" below the fastener, tightly wrap the connection with electrical tape so that
the connections seals the end of the fastener.
4. Connect the black fixture lead to the black wire in the outlet box.
5. Attach the CANOPY (3) to the MOUNTING STRAP (1) and secure it with the RS CAP (4).
6. Screw the BULB (5) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 40 WATT TYPE G 16 1/2
LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
7. Restore power to the outlet at the breaker or fuse box.
Loading...