Corbett Lighting 398-32 INSTALLATION INSTRUCTIONS

FIXTURE INSTALLATION

1. Slide crimp type cable clamp onto the safety cable. Feed the SAFETY CABLE (18) down through one of the
holes in the top of the outlet box. Loop the SAFETY CABLE over the approved support. Feed the SAFETY
CABLE (18) back through the top of the box and the cable clamp. Using the crimping tool, tightly crimp the
cable clamp to lock the SAFETY CABLE (18) in position.

2. Feed the wire through the STEM (8) and twist tightly onto the FIXTURE ASSEMBLY (9). Keep adding additional
stems until you desired hanging height is met.

3. Slide in CANOPY(5) onto the STEM (8), and thread the SWIVEL (6) onto the top end of the STEM (8).

4. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the
MOUNTING SCREWS (2).

This fixture is designed to be mounted on standard round or octagon junction box.

The junction box must be securely mounted to the structure of the building.

5. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire

5
8

".

6. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (4) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

7. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener ( WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

8. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same
as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD

RESULT IN SERIOUS INJURY OR DEATH!

9. Push the wires back into the junction box. Lift up the CANOPY (5) up to the ceiling, and secure with the

END

NUT

(7)

.

10. Insert the GLASS ROD (17) into the GLASS ROD HOLDER (14). MAKE SURE THE CODES MATCH.

(Reference image 1)

11. Adjust the orientation of SWIVEL (10) to facilitate the installation of GLASS BALL (16).

12. Screw the BULB (15) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 60 WATT LAMP. DO

NOT EXCEED THE RECOMMENDED WATTAGE!

CELESTIAL

398-32

INSTALLATION INSTRUCTIONS

www.hvlgroup.com

Questions? We're here to help!

Contact us at [e-mail]

WARNING/CAUTION

· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.

· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS

AFTER USE.

· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR

TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

4

5
6

7

8

1
2
3

9

10

11

12

13

15

16

17

14

18

R

CELESTIAL

398-32

INSTALLATION INSTRUCTIONS

www.hvlgroup.com

Questions? We're here to help!

Contact us at [e-mail]

27

28

29

Reference image 1

FIXTURE INSTALLATION

13. Tilt and rotate the GLASS BALL (16) so that the GLASS BALL HOLDER (13) into GLASS
BALL (16), hold GLASS BALL FITTER (12) against GLASS BALL (16) and secure with the
RING (11).

14. Adjust the position of SWIVEL (10) so that the GLASS BALL (16) placed in the GLASS
ROD HOLDER (14).

15. Restore power to the outlet at the breaker or fuse box.

ITEM DESCRIPTION

PART NUMBER

1

MOUNTING PLATE

HDW-398-32

2

MOUNTING SCREW

HDW-398-32

3

GROUND SCREW

HDW-398-32

4

WIRE NUT

HDW-398-32

5

CANOPY

CPY-398-32

6

SWIVEL

SWL-398-32-1

7

END NUT

HDW-398-32

8

STEM

STM-398-32-06, 12, 18

9

FIXTURE ASSEMBLY

FAS-398-32

10

SWIVEL

SWL-398-01-2

11

RING

RNG-398-01

12

GLASS BALL FITTER

FIT-398-01

13

GLASS BALL HOLDER

BLL-398-01

14

GLASS ROD HOLDER

ROD-398-01-H

15

BULB

NOT INCLUDED

16

GLASS BALL

GLS-398-01

17

GLASS ROD

ROD-398-01

18

SAFETY CABLE

CBL-398-32

R

FIXTURE INSTALLATION

1. Slide crimp type cable clamp onto the safety cable. Feed the SAFETY CABLE (18) down through one of the
holes in the top of the outlet box. Loop the SAFETY CABLE over the approved support. Feed the SAFETY
CABLE (18) back through the top of the box and the cable clamp. Using the crimping tool, tightly crimp the
cable clamp to lock the SAFETY CABLE (18) in position.

2. Feed the wire through the STEM (8) and twist tightly onto the FIXTURE ASSEMBLY (9). Keep adding additional
stems until you desired hanging height is met.

3. Slide in CANOPY(5) onto the STEM (8), and thread the SWIVEL (6) onto the top end of the STEM (8).

4. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the
MOUNTING SCREWS (2).

This fixture is designed to be mounted on standard round or octagon junction box.

The junction box must be securely mounted to the structure of the building.

5. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire

5
8

".

6. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (4) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

7. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener ( WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

8. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same
as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD

RESULT IN SERIOUS INJURY OR DEATH!

9. Push the wires back into the junction box. Lift up the CANOPY (5) up to the ceiling, and secure with the

END

NUT

(7)

.

10. Insert the GLASS ROD (17) into the GLASS ROD HOLDER (14). MAKE SURE THE CODES MATCH.

(Reference image 1)

11. Adjust the orientation of SWIVEL (10) to facilitate the installation of GLASS BALL (16).

12. Screw the BULB (15) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 60 WATT LAMP. DO

NOT EXCEED THE RECOMMENDED WATTAGE!

CELESTIAL

398-32

INSTALLATION INSTRUCTIONS

www.hvlgroup.com

Questions? We're here to help!

Contact us at [e-mail]

4

5
6

7

8

1
2
3

9

10

11

12

13

15

16

17

14

18

R

ATTENTION PRUDENCE

· DÉBRANCHEZ L'ALIMENTATION AVANT DE REMPLIR OU DE CÂBLER LE LUMINAIRE. LISEZ

COMPLÈTEMENT TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L'INSTALLATION

· POUR ÉVITER LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, LE LUMINAIRE DOIT ÊTRE INSTALLÉ

CONFORMÉMENT À TOUS LES CODES ÉLECTRIQUES/DE CONSTRUCTION NATIONAUX ET LOCAUX

APPLICABLES. L'INSTALLATION ET L'ENTRETIEN DE CET APPAREIL DOIVENT ÊTRE EFFECTUÉS PAR UN

ÉLECTRICIEN AGRÉÉ OU UN TECHNICIEN CERTIFIÉ FORMÉ EN USINE.

· CALIFORNIE PROP 65 : CET APPAREIL D'ÉCLAIRAGE CONTIENT DES PRODUITS CHIMIQUES CONNUS PAR

L'ÉTAT DE CALIFORNIE POUR PROVOQUER LE CANCER, DES MALADIES CONGÉNITALES ET/OU D'AUTRES
DOMMAGES À LA REPRODUCTION. LAVER LES MAINS APRÈS UTILISATION.

· RETIRER LE LUMINAIRE, LES PIÈCES ET LE(S) SAC(S) DE PIÈCES DU CARTON. AVANT DE JETER LE

CARTON, VÉRIFIEZ DOUBLE POUR VOUS ASSURER QUE TOUTES LES PIÈCES SONT TROUVÉES.
INSPECTER LE LUMINAIRE AVANT L'INSTALLATION POUR TOUT DOMMAGE AU LUMINAIRE.

· GRADATION : LE LUMINAIRE PEUT ÊTRE CONTRLÉ PAR UN DISPOSITIF DE GRADATION MURALE. UTILISER

UNIQUEMENT UN GRADATEUR TRIAC/ÉLECTRONIQUE. ASSUREZ-VOUS QUE LE CARTON EST MARQUÉ
POUR UNE UTILISATION AVEC UNE SOURCE DE LUMIÈRE FLUORESCENTE À INCANDESCENTE COMPACTE
UNIQUEMENT. CEUX-CI PEUVENT ÊTRE FOURNIS PAR VOTRE DISTRIBUTEUR ÉLECTRIQUE LOCAL,
CENTRE À DOMICILE OU MAGASIN DE QUINCAILLERIE.

· VEUILLEZ NETTOYER UNIQUEMENT AVEC UN CHIFFON DOUX ET SEC ! N'UTILISEZ PAS DE NETTOYANTS

CELESTIAL

398-32

INSTALLATION INSTRUCTIONS

www.hvlgroup.com

Questions? We're here to help!

Contact us at [e-mail]

27

28

29

Reference image 1

FIXTURE INSTALLATION

13. Tilt and rotate the GLASS BALL (16) so that the GLASS BALL HOLDER (13) into GLASS
BALL (16), hold GLASS BALL FITTER (12) against GLASS BALL (16) and secure with the
RING (11).

14. Adjust the position of SWIVEL (10) so that the GLASS BALL (16) placed in the GLASS
ROD HOLDER (14).

15. Restore power to the outlet at the breaker or fuse box.

ITEM DESCRIPTION

PART NUMBER

1

MOUNTING PLATE

HDW-398-32

2

MOUNTING SCREW

HDW-398-32

3

GROUND SCREW

HDW-398-32

4

WIRE NUT

HDW-398-32

5

CANOPY

CPY-398-32

6

SWIVEL

SWL-398-32

7

END NUT

HDW-398-32

8

STEM

STM-398-32-06, 12, 18

9

FIXTURE ASSEMBLY

FAS-398-32

10

SWIVEL

SWL-398-01

11

RING

RNG-398-01

12

GLASS BALL FITTER

FIT-398-01

13

GLASS BALL HOLDER

BLL-398-01

14

GLASS ROD HOLDER

ROD-398-01-H

15

BULB

NOT INCLUDED

16

GLASS BALL

GLS-398-01

17

GLASS ROD

ROD-398-01

18

SAFETY CABLE

CBL-398-32

R