CORBERO CCML1970NFX Instruction Manual

REFRIGERATOR
INSTRUCTION MANUAL
MODEL: CCML1970NFX
INTRODUCTION
Before use
Please read these instructions and the Safety guidelines on page 1 carefully before using your new Fridge/Freezer. The Fridge/Freezer is for indoor, domestic use only.
No
Description
1
Lighting switch
2
Cooling room shelves
3
Light
4
Vegetable and fruit crisper
5
Vegetable and fruit crisper cover
6
Freezing drawers
7
Door balcony
INSTALLATION
Location
When selecting a position for your Fridge/Freezer you should make sure the floor is flat and firm, and the room is well ventilated with an average room temperature of between 16and 43℃. Avoid locating your Fridge/Freezer near a heat source, eg, cooker, boiler or radiator. Also avoid direct sunlight in out-buildings or sun lounges. If you are placing your Fridge/Freezer in an out-building such as a garage or annex ensure that the Fridge/Freezer is placed above the damp course, otherwise condensation will occur on the Fridge/Freezer cabinet. Never place the Fridge/Freezer in a wall recessed or into fitted cabinets or fumiture when your Fridge/Freezer is working, the grille at the back may become hot and the sides warm. It must therefore be installed so that the back of the Fridge/Freezer has at least 9cm(31/2”) of free space and the sides have 2cm(3/4”). Do not drape the Fridge/Freezer with any covering.
Leveling the Fridge/Freezer
If the Fridge/Freezer is not level, the door and magnetic seal alignment will be affected and may cause you Fridge/Freezer to work incorrectly. Once the Fridge/Freezer is placed in its final location, adjust the leveling feet at the front by turning them.
Cleaning before use
Wipe the inside of the Fridge/Freezer with a weak solution of bicarbonate of soda. Then rinse with warm water using a damp sponge or cloth. Wash the baskets and shelves in warm soapy water and dry completely before replacing in the Fridge/Freezer. The external parts of the Fridge/Freezer can be cleaned with wax polish.
Before plugging in YOU MUST
Check that you have a socket which is compatible with the plug supplied with the Fridge/Freezer. If not see the section called ELECTRICAL INFORMATION
Before switching on!
DO NOT SWITCH ON UNTIL FOUR HOURS AFTER MOVING THE FRIDGE/FREEZER. The coolant fluid needs time to settle. If the appliance is switched off at any time, wait 30 minutes before switching back on to allow the coolant fluid to settle.
Before filling your Fridge/Freezer
Before storing foods in your Fridge/Freezer, turn the Fridge/Freezer on and wait for 24 hours, to make sure it is working properly and to allow the Fridge/Freezer to fail to the correct temperature.
START Testing
1. Clean the parts of the refrigerator with lukewarm water containing a littleneutral detergent and with clear water, and wipe them dry.
Notes: Electric parts of the refrigerator can only be wiped by dry cloth.
2.Turn on electricity. The compressor begins to work.
3.Open the door 30 minutes later, if the temperature in the refrigerator decreased obviously, it shows that the refrigerator system works well. When the refrigerator operates for a period of time, the temperature controller will automatically set the temperature within limits it opens.
The display is located in the middle of the refrigerator door. Please refer to the below figure for the layout.
Introduction of the buttons
1Fridge: to set the refrigerator temperature 2Freezer: to set the freezer temperature 3Function: to choose functions of fast cooling, fast freezing, intelligence
and vacation 4 OK: to enter or to quit the existing function Function setting appliance connected to power at the first time When the appliance is connected to power at the first time, the display will be lit for 2 seconds before going normal and the appliance runs with intelligence function. display control
When the refrigerator door is closed and there is no button operation in 3 minutes, the display light goes off. When the display light is off, open the refrigerator door or click any button to light it up.
temperature setting
1) Click the “refrigerator” or “freezer” button and when it flickers in the symbol, temperatures can be set; each time when the button is clicked, the temperature changes accordingly (the display shows the temperature accordingly).
(Temperatures cannot be set under functions of fast cooling, fast freezing, intelligence and
vacation,)
2) Under temperature setting, if there is no button operation in 5 seconds, the button stops
flickering and the set temperature comes into effect.
3) Temperature cycle
Refrigerator: 2→3→4→5→6→7→8→OFF→2℃; Freezer: -24-23-22-21-20-19-18-17-16-24℃;
intelligence Under intelligence, it is 4 in the refrigerator and -18 in the freezer. Temperatures cannot be changed and you can click the temperature zone button to check the temperature.
1) To enter intelligence
Click “option” until it flickers and then click “OK” to enter this function.
2) To quit intelligence
Under intelligence, click “option” until it goes to intelligence, click “OK” to quit this function and
the light goes off. Temperatures of each chamber go back to the value beforeintelligence function.
fast cooling Under fast cooling, it is 2 in the refrigerator and the refrigerator temperature cannot be changed.
1)To enter fast cooling
Click “option” until it flickers in “fast cooling” and then click “OK” to enter this function.
2) To quit fast cooling
Under fast cooling, click “option” until it goes to “fast cooling” and then click “OK” to quit this
function. The light in fast cooling goes off and the refrigerator temperature goes back to the value before fast cooling.
fast freezing Under fast freezing, refrigerator temperature can be set but not for the freezer temperature.
1) To enter fast freezing
Click “option” until it flickers in “fast freezing” and then click “OK” to enter this function.
2) To quit fast cooling
Under fast freezing, click “option” until it goes to “fast freezing” and then click “OK” to quit this
function. The light in fast freezing goes off and the freezer temperature goes back to the value before fast freezing. When fast freezing time is up (26 hours), it quits automatically. When it goes to intelligence, fast freezing stops.
vacation Under vacation, it is 14 in the refrigerator and the temperatures in this chamber cannot be changed.
1) To enter vacation
Click “option” until it flickers in “fast freezing” and then click “OK” to enter this function.
2) To quite vacation
Under vacation, click “option” until it goes to “vacation” and then click “OK” to quit this function. The light in vacation goes off and the refrigerator temperature goes back to the value before vacation. Vacation quits under functions of intelligence and fast cooling.
power off memory With this design, the refrigerator can automatically keep all the setting in case of power off. When the unit is plugged in again, the refrigerator will run with the setting before power off.
Power-On Delay To prevent harm to the refrigerator in case of sudden power cut and power on, the unit does not start immediately if the power off time is less than 5 minutes.
Freezer over-temperature alarm (only in case of power on) When the freezer temperature is higher than 10at the first time connected to power, the symbol light of the freezer chamber goes on and the number representing temperature flickers. Press any button or wait for 5 seconds, flickering stops and it goes back to the temperature that was set.
Refrigerator door opening alarm When the refrigerator is open over 3 minutes, the buzzer will buzz. Close the door or press any button to stop the alarm, but for the latter, the alarm will go off again after 3 minutes.
Sensor fault alarm When it shows “E0”, “E1”, “E2” or other abnormal symbols, it means sensor faults and the refrigerator needs repair.
IN USE
Tips for keeping food perfect in the Fridge
Take extra care with meat and fish
Cooked meats should always be stored on a shelf above raw meats to avoid bacterial transfer. Keep raw meats on a plate which is large enough to collect juices and cover it with cling film or foil.
Leave space around food
This allows cold air to circulate around the Fridge, ensuring all parts of the Fridge are kept cool.
Wrap up food!
To prevent transfer of flavors and drying out, food should be separately packed or covered. Fruit and vegetables need not be wrapped.
Pre-cooked food should be cooled properly
Allow pre-cooked food to cool down before placing in the Fridge. This will help to stop the internal temperature of the Fridge from rising.
Shut the door!
To prevent cold air escaping, try to limit the number of times you open the door. When retuning from shopping, sort foods to be kept in your Fridge before opening the door. Only open the door to put food in or take it out.
Where to store your foods in the fridge
Cool area
This is where to store foods which will keep longer if they are kept cool. Milk, eggs, yogurt, fruitjuices, hard cheeses eg. Cheddar. Opened jars and bottles of salad dressings, sauces and jams. Fats, eg. Butter, margarine, low-fat speads, cooking fats and lard.
Coldest area: 2 to 5
This is where foods which must be cold to keep them safe should be kept:
·Raw and uncooked foods should always be wrapped.
·Pre-cooked chilled foods, eg. Ready meals, meat pies, soft cheeses.
·Pre-cooked meats eg. Ham,
·Prepared salads(including pre-packed mixed green salads, rice, potato salad etc).
·Desserts, eg. Fromage frais, home-prepared food and leftovers or cream cakes.
Salad bin
This is the most humid part of the Fridge. Vegetables, fruit, fresh salad items eg. Unwashed whole lettuce, whole tomatoes, radishes etc can be stored here. WE RECOMMEND THAT ALL PRODUCE KEPT IN THE SALAD BIN IS WRAPPED. NOTE:Always wrap and store raw meat, poultry and fish on the lowest shelf at the bottom of the fridge. This will stop them dripping onto, or touching other foods. Do not store inflammable gasses or liquids in the fridge.
Tips for shopping for frozen foods
Your Freezer is 4 star
When you are buying frozen food, look at the Storage Guidelines on the packaging. You will be able to store each item of frozen food for the period shown against the 4 star rating. This is usually the period stated as “Best, Before”, found on the front of the packaging.
Check the Fridge/Freezer temperature
Check the temperature of the frozen food cabinet in the shop where you buy your frozen foods. It should show a temperature lower than -18.
Choose packs carefully
Make sure the frozen food package is in perfect condition.
Purchase frozen food last
Always buy frozen products last on your shopping trip or visit to the supermarket.
Keep frozen foods together Try to keep frozen food together whilst shopping, and on the journey home as this will help to keep the food cooler.
Store food straight away
Don’t buy frozen food unless you can freeze it straight away. Special insulated bags can
be bought from most supermarkets and hardware shops. These keep frozen food cold for longer.
Thawing frozen food
For some foods, thawing before cooking is unnecessary. Vegetables and pasta can be added directly to boiling water or steam cooked. Frozen sauces and soups can be put into a saucepan and heated gently until thawed.
Freezing fresh foods, useful tips
Use quality food and handle it as little as possible. Freeze food in small quantities, it freezes faster, takes less time to thaw and enables you to eat it in the quantity you need.
Freezing fresh foods
First, estimate the amount of food you will be freezing. If you are freezing large amounts of fresh food, remember to turn the control dial to Max. This will lower the temperature in the Freezer (approx -30), freezing your food quicker and helping to keep the goodness in. However you should do this sparingly to conserve energy.
Preparations for freezing
Leave cooked food to cool completely. Chill food in a Fridge before freezing if possible. Consider how you want to cook the food before freezing it.
Don’t freeze food in metal containers as you may want to microwave it straight from the
Freezer. Use special Freezer bags available from supermarkets, Freezer film, polythene bags, plastic containers, aluminum foil for acidic foods(such as citrus fruits). Do not use thin cling film or glass. Do not use used food containers (unless cleaned thoroughly first). Exclude as much air from the container as possible. You could buy a special vacuum pump which sucks excessive air out of the packaging. Leave a small amount of “air space” when freezing liquids, to allow for expansion. You can use the space in the Freezer most efficiently if you freeze liquids(or solids with liquids, such as stew) in square blocks. This is known as “performing” Pour the liquid into a polythene bag which is inside a square sided container. Freeze it like this, then remove it from the container and seal the bag.
Defrosting
This appliance is designed as automatic defrosting ,no need to defrost by hand.
Recommended storage periods
For recommended food storage time, refer to the information given on your food packaging.
Cleaning inside the Fridge/Freezer
You should clean the Fridge/Freezer internally with a weak solution of bicarbonate of soda. Then rinse with warm water using a damp sponge or cloth and wipe dry. Wash the baskets in warm soapy water and ensure they are completely dry before replacing in the Fridge/Freezer.
Cleaning outside the Fridge/Freezer
Use standard non-abrasive detergent diluted in warm water to clean the Fridge/Freezer exterior. The grille of the condenser at the back of the Fridge/Freezer and the adjacent components can be vacuumed using a soft brush attachment. Do not use harsh cleaners, scouring pads or solvents to clean any part of the Fridge/Freezer
TROUBLESHOOTING AND MAINTENANCE
Trouble Shooting
Power cut
If the internal temperature of the Fridge/Freezer compartment is -18 or less when the
power returns, your food is safe. The food in your Fridge/Freezer will remain frozen for approx 16 hours with the door closed. Do not open the Fridge/Freezer door more than necessary.
The Fridge/Freezer is exceptionally cold
You may have accidentally set the refrigerator temperature to a higher position.
The Fridge/Freezer is exceptionally warm
The compressor may not be working. Set the refrigerator temperature to maximum setting and wait a few minutes. If there is no humming noise, it is not working. Contact the local store where your purchase was made.
The Fridge/Freezer is not working
Check it is plugged in and switched on. Check that the fuse in the plug has not blown. Plug in another appliance, such as a lamp, to see if the socket is working. The Fridge/Freezer should be placed in a well ventilated room with an ambient temperature of between 16and 32. Leave the Fridge/Freezer for 30 minutes.
Condensation appears on the outside of the Fridge/Freezer
This may be due to a change in the room temperature. Wipe off any residue of moisture. If the problem continues, contact the local store where your purchase was made.
GURGLING, WHOOSHING
These noises are caused by the circulation of the refrigerant liquid in the cooling system. It has become more pronounced since the introduction of CFC free gases. This is not a fault and will not affect the performance of your Fridge/Freezer.
HUMMING, PURRING OR PULSATING
This is the compressor motor working, as it pumps the refrigerant around the system.
Servicing
This product should be serviced by an authorized engineer and only genuine spare parts should be used. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact the local store where your purchase was made. When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells.
Lamp Replacement
LED light is used in this appliance, which with low energy consumption & long life. If anything abnormal, please contact after-sale service for help.
Reversing the Door Swing
一: Disassemble the refrigerator/freezer door
1. a Use a tool to remove the screw off the hinge cover, and then remove the latter.
Insert the communication line to the hole on the cabinet top.
b. Use a tool to remove the 4 screws off the upper hinge cover and then remove the latter. Pry up the door bush and small end cap cover on the door.
10
c.Insert the door bush and door communication line into the hole on the door and then put on the small end cap cover.
d Use a tool to remove the 2 screws as shows in the below figure to remove the hole cover on the cabinet top and get the cabinet communication line out of the hole. Pry up the small end cap cover on the door and get out the door bush and door communication line.
e Insert the door bush into the round hole on the door and then put on the small end cap cover.
Loading...
+ 30 hidden pages