Corbero ZD19-4R5 User Manual

m Warnings for your safety

Warnings for your safety. Carefully read these instructions before installing and using the machine.

m This freezer is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product.

m Any electrical work required to install the appliance should be carried out by a qualified electrician or competent person.

m This appliance is heavy. Care should be taken when moving it.

m Make sure that the cable is not trapped underneath the appliance, nor touches the motor.

m Repairs carried out by inexperienced persons may cause injuries or serious malfunctioning. Refer to the nearest Authorized Dealer.

m Make sure the rear part of the appliance stands against a wall as there are working parts which heat up and should not be of easy access.

m Make sure that there is a continous and adequate ventilation as a failor to do so will result in component failure and possible food loss.

m The appliance should be left for at least 4 hours after installation before it is turned on ill order to allow the refrigerant to settle.

m This product must be serviced only by an authorized NETWORK SERVICE CENTRE, and only genuine SPARE PARTS must be employed.

m Before cleaning or reparing the appliance, make sure it is unplugged.

m It is dangerous to alter the specifications or modify this product in any way.

mThesedomesticrefrigerators are designed to be used specifically for the storage and conservation of food.

mDO NOT USE SHARP INSTRUMENTS to scrap off frost or ice. Frost may be removed by using a plastic scraper. (See defrosting instructions).

m Frozen food must not be re-frozen once it has been thawed out.

m Manufacturer’s storage recommendations should be strictly complied with.

m The lollies can cause frost burns if consumed right away from the freezer.

m Do not place carbonate or fizzy drinks in the freezer as these may explode.

m Whenever there is a need for discarding an old freezer make sure to:

m Take off the doors in order to prevent children trapped inside.

Have the gas from the cooling system recovered before making it to scrap iron.

Índex

Warnings for your safety	pag. 15
Installation	pag. 17
Changing the opening directions
of the doors and panelling	pag. 18 - 19
Regulation and Control	pag. 20
How to use your
Refrigerator-Freezer	pag. 21
Maintenance of your
Refrigerator-Freezer	pag. 22 - 23
Something not working	pag. 24 - 25
Normal noises when
functioning	pag. 26
Guarantee, Service
and Spare Parts	pag. 27
Tecnical Features	pag. 28

Installation

Positioning

•Place the refrigerator away from direct sunlight and heat sources.

•Maintain recommended ventilation - see Fig. 1.

•Make sure the refrigerator is accurately levelled turning the adjustable feet in order to avoid vibrations and noises Fig. 2.

•This is a built in design to be aligned with other furniture.

•The appliance should be only set up at a location whose ambient temperature corresponds to the climate classification, for which the appliance is designed.

•The climate classification can be found on the serial plate of the appliance.

•The following table shows which ambient tempera-

ture is correct for each climate classification:

Climate classification	for an ambient temperature of
SN	+ 10 to + 32°C
N	+ 16 to + 32°C
ST	+ 18 to + 38°C
T	+ 18 to + 43°C

•However, the manufacturer make sure the correct operation of the appliance from minimum temperature of 10°C to upper limit of each climatic class.

Cleaning the interior

•Do not use alcohol or any cleanig product containing alcohol because it can damage the cabinet.

•Before using the appliance for the first time wash the interior whith luke warm water and some neutral soap so as to remove the typical smell of a brandnew product and then dry thoroughly.

•Do not use detergents or abrasive powders as these will damage the finish.

•Remove security used for transportation.

wiring system are not grounded, have the appliance connected to a separate ground wire in accordance with existing safety regulations.

«THE MANUFACTURER DECLINES TO ACCEPT ANY LIABILITY IF THIS SAFETY RULE IS NOT OBSERVED».

Starting – up

•Plug the appliance into the mains.

•Turn to intermediate position the knobs of the «temperature regulators» «A» Fig. 5.

•Make sure the inner light «H» turns on when opening de door.

Fig. 1

Electrical connection

mBefore plugging the appliance into a socket make sure that the voltage and frequency shown on the rating plate correspond to your home supply.

mIt is essential that the appliance be connected to an efficient earth tap.

For this purpose the supply cable plug incorporates a Fig. 2 special earth contact. If the sockets of your domestic

Changing the opening direction of doors and Panelling

Changing the opening direction of the doors

If you wish to change the opening side of the doors proceed as follows:

1... Remove the handles of the doors, if they are side fixing by screws.

2... If your appliance carries a plinth, remove it pulling from it smoothly. Take off the small lid on the left (to let the lower hinge enter into it) and place it on the right side of the plinth.

3... Remove the lower hing taking care for the lower door not to fall off. You could have better access to the lower hinge by tilting the refrigerator.

4... Lift the lower door off the central hinge.

5... Remove the central hinge taking care for the upper door not to fall off and not to lose the plastic washer.

6... Take the upper door off the upper hing.

7... The upper hing must be removed, removing at Fig. 3 once, the plastic lid covering it.

8... All small plastic covers are useful now to cover new holes on the opposite side of the doors.

Changing the opening direction of doors and Panelling

If you refrigerator has top panel (fig. 4), you can manage in the same way from point 1 to point 6 and then:

7... Unscrew the axle of the upper hing (9 Fig. 4) and replace it at the opposite side (10 Fig. 4).

8... Remove the little lid put on the opposite side of the central hinge and use it to cover the new holes left

where the hinge was placed.

Fig. 4

For the remaining parts proceed the other way round.

Once finished make sure that all joints close perfectly well all around the door and chek that the internal light turns of when the fridge door closes.

How to panel the doors:

If your appliance is provided with metal strips for panelling and you wish to do so proceed as follows:

1... Remove one of the side strips.

2... Loosen the screws of the remaining strips.

3... Start putting on the panel where you took off the strip pushing it right up to the end.

4... Replace the strip on this side.

5... Tighten all screws

NOTE: The panel dimensions must be 2 mm. shorter than the doors. Maximun thickness of the panel is 4 mm.

+ 9 hidden pages