Coral Industries 84K User Manual
84K-GP
Neo Angle Shower Enclosure
Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time)
1-877-723-7190 (Toll Free)
84K-GP 3/07
PARTS LIST
FRAME PACKAGE
K EY DESCRIPTION PART QTY
A SIDE PANEL 2
B DOOR PANEL / CORNER POST 1
C JAMB A310 2
D DRIP RAIL A710 1
E DRIP RAIL SWEEP VS91 1
F DRIP RAIL TAPE (I) HT52 1
HARDWARE BAG
G 8A X 3/8 TRUSS HEAD SCREW H470 6
H 8A X 3/4 FLAT HEAD SCREW H467 6
I 8A X 1 1/4 PAN HEAD SCREW H480 6
J ANCHOR H002 6
K DRIP RAIL PLUG HA28 1
L CLEAR CORNER BRACE * HB13 2
M 8A X 5/8 PAN HEAD SELF-DRILLING SCREW * H437 4
N PULL HANDLE KIT + HSAD 1
EXTERIOR PULL HANDLE HA31 1
INTERIOR PULL HANDLE HA32 1
6-32 X 1 1/4 PAN HEAD SCREW H485 2
Optional (I) Pre-Installed (+) May be Pre-Installed
*
TOOLS
NEEDED
1/8" Drill Bit
3/16" Drill Bit
(3/16" Masonry Bit for
Ceramic Tile)
Measuring Tape
Phillips Screw Driver
File
Drill
Level
China Marker
Caulking Compound
Before starting installation of your new enclosure, carefully read all instructions
and lay out parts to become familiar with their identity.
USE OF ANCHORS
Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure
to a fiberglass unit or wall surround with board reinforced mounting areas. Mounting holes in this case should be drilled with
an 1/8" drill bit.
Mounting this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes in
the tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors into
the holes making certain that ring on large end of anchor meets the surface of the tile.
CLEANING
Cleaning and care of your enclosure is important to its lasting beauty. A nonabrasive liquid cleaner is recommended.
Never use scouring powder or pads.
SEALING
The use of a caulking compound can assure a water-tight seal when applied along outside edge of the enclosure where metal
and bath meet. If desired, caulk inside of enclosure where jambs meet walls.
Do not try to cut the mirrors or glass used in this enclosure.
Tempered glass and mirrors will disintegrate if cut.
84K-GP 3/07
H470
G
TRUSS HEAD SCREW
HB13
L
CLEAR CORNER BRACE
H437
M
PAN HEAD SELFÂDRILLING SCREW
C
A310
JAMB
A
SIDE
PANEL
H
H467
FLAT
HEAD
SCREW
DOOR PANEL/
B
CORNER POST
N
PAN HEAD
SCREW
HT52
DRIP RAIL TAPE
F
DRIP RAIL VINYL
A710
DRIP RAIL
VS91
PULL
HANDLE
KIT +
H485
HA32
INTERIOR
HANDLE
D
E
HA31
EXTERIOR
HANDLE
K
HA28
DRIP RAIL PLUG
A
SIDE
PANEL
H480
PAN HEAD
SCREW
I
J
H002
ANCHOR
8A x 3/4 Flat Head Screw
H
(H467 - Used for attaching
Side Panel to Corner Post)
8A x 5/8 Pan Head Self-Drilling Screw
M
(H437 - Used for Corner Braces)
OUTSIDE OF SHOWER
8A x 1 1/4 Pan Head Screw
I
(H480 - Used for Jambs)
8A x 3/8 Truss Head Screw
G
(H470 - Used for Side Panels and
Drip Rail)
6-32 x 1 1/4 Pan Head Screw +
N
(H485 - Used for Pull Handle)
+ May be Pre-Installed
84K-GP 3/07
Loading...