7631 / 7131 - GP
(7641 / 7141 - GP)
Pivot Door
Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time)
1-877-723-7190 (Toll Free)
7631 / 7131-GP 9/06
PARTS LIST
FRAME PACKAGE
DESCRIPTIONKEY PART QTY
A SILL A263 1
B PIVOT JAMB A960 1
C STRIKE JAMB A961 1
D DRIP RAIL A710 / V667 1
E DRIP RAIL SWEEP
F MAGNETIC STRIP H170 1
G DRIP RAIL TAPE
I PIVOT DOOR SLIDE BLOCK
K PIVOT VINYL
HARDWARE BAG
H DRIP RAIL PLUG HA28 1
L PIVOT PLATE HA65 2
M PIVOT PIN
N NYLON WASHER HW81 1
O 8-32 X 1/2 HEX HEAD SCREW HP05 2
P 8A X 3/8 PAN HEAD SELF-DRILLING SCR H900 4
S 8A X 5/8 PAN HEAD SELF-DRILLING SCR H437 2
Q ANCHORS H002 6
R 8A X 1 1/4 FLAT HEAD SCREW H810 6
J PULL HANDLE KIT
EXTERIOR HANDLE HA31 1
INTERIOR HANDLE HA32 1
6-32 X 1 1/4 PAN HEAD SCREW H485 2
(I)
Optional
Pre-Installed
*
May be Pre-Installed
**
(I)
*
*
*
*
**
VS91 1
HT52 1
HPT3 2
V517 1
HPHD 2
HSAD 1
TOOLS
NEEDED
1/8" Drill Bit
3/16" Drill Bit
(3/16" Masonry Bit for
Ceramic Tile)
Pencil
Measuring Tape
Hacksaw
Phillips Screw Driver
Silicone Caulk
File
Drill
Level
Masking Tape
Hex Head Wrench
Before starting installation of your new enclosure, carefully read all instructions
and lay out parts to become familiar with their identity.
USE OF ANCHORS
Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure
to a fiberglass unit or wall surround with board reinforced mounting areas. Mounting holes in this case should be drilled with an
1/8" drill bit.
Mounting of this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes in
the tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors into
the holes making certain that ring on large end of anchor meets the surface of the tile.
CLEANING
Cleaning and care of your enclosure is important to its lasting beauty. We suggest using a nonabrasive liquid cleaner.
Never use scouring powder or pads.
SEALING
The use of a caulking compound can assure a water-tight seal when applied along outside edge of the enclosure where metal and
bath meet. If desired, caulk inside of enclosure where jambs meet walls.
Do not try to cut the mirrors or glass used in this enclosure.
Tempered glass and mirrors will disintegrate if cut.
7631 / 7131-GP 9/06
PAN HEAD SELF-
DRILLING SCREW
H900
P
HA65
L
PIVOT
PLATE
H437
PAN HEAD SELF-
S
DRILLING SCREW
V517
PIVOT VINYL
R
H810
FLAT
HEAD
SCREW
K
HPHD
PIVOT PIN
M
HP05
HEX HEAD
O
SCREW
I
HPT3
PIVOT DOOR
SLIDE BLOCK
PULL HANDLE KIT**
PAN HEAD
A710
DRIP
RAIL
D
HSAD
H485
SCREW
INTERIOR
HT52
DRIP
RAIL
TAPE
G
J
HA32
HANDLE
MAGNETIC
HA31
EXTERIOR
HANDLE
HA28
DRIP
RAIL
PLUG
H
H170
STRIP
F C
R
H810
FLAT
HEAD
SCREW
A961
STRIKE
JAMB
Q
H002
ANCHORS
B
A960
PIVOT JAMB
8A x 5/8 Pan Head Self-Drilling
S
Screw
(H437 - Used for Pivot Plates)
8-32 x 1/2 Hex Head Screw
O
(HP05 - Used for Pivot Door Slide
Block)
VS91
E
DRIP RAIL SWEEP
HW81
N
NYLON WASHER
OUTSIDE OF SHOWER
8A x 3/8 Pan Head Self-Drilling
P
Screw
(H900 - Used for Pivot Plates)
J
A263
A
SILL
** May be Pre-Installed
8A x 1 1/4 Flat Head Screw
R
(H810 - Used for Jambs)
6-32 x 1 1/4 Pan Head Screw
(H485 - Used for Pull Handle Kit)
7631 / 7131-GP 9/06